1. Introduction
This manual provides detailed instructions for the operation and maintenance of the JIKONG 4.3-inch LCD display screen, model JK-4.3LCD-TTL-P. This display is designed for use with JIKONG BMS systems, including V19 versions such as PB1A16S10P, PB1A16S15P, PB2A16S15P, PB2A16S20P, and PB2A16S30P, offering a comprehensive communication and monitoring interface.


2. Product Features
- Wide Power Supply Range: Supports 9V to 36V DC input.
- Comprehensive Display: Shows battery total voltage, battery current, battery power, single series voltage, and individual cell voltages.
- Communication: TTL level supported with a default baud rate of 115200bps.
- Multilingual Support: Supports Chinese, English, Thai, and Vietnamese language switchover.
- Customization: Allows for display interface customization, including language, logo, and overall interface design.
- BMS Control: Features a key extension interface for controlling BMS startup and shutdown.
3. Specifications
3.1. General Parameters
| Parameter | Data |
|---|---|
| Display Category | TFT |
| Display Size | 4.3-inch |
| Resolution | 480*272 |
| Backlight Type/Brightness | LED/300nit |
| Viewing Angle L/R/U/D | 85°/85°/85°/85° |
| Accessory Type | Battery Accessories |
| Charger Included | No |
| Battery Included | No |
| High-concerned chemical | None |
| Certification | CE, FCC, RoHS |
3.2. Power Supply
| Parameter | Min | Max |
|---|---|---|
| Supply Voltage (with power reverse protection) | 9V | 36V |
| Power Dissipation | 1.32W (12V@110mA) | |
3.3. Environmental Parameters
| Parameter | Min | Max | Unit |
|---|---|---|---|
| Operating Temperature | -20 | +70 | °C |
| Storage Temperature | -30 | +80 | °C |
| Operating Humidity | 10% | 90% | RH |
3.4. Product Dimensions

4. Setup & Installation
4.1. External Interfaces
The display features two main interfaces:
- User Interface: Used for power supply and serial port signal connection. It utilizes a HY2.0mm-6P vertical stick socket.
- Key Extension Interface: Used to control the BMS startup and shutdown. It uses an A1254WF-6A vertical sticker socket.

4.2. Pin Definition
The display end interface adopts a HY2.0 mm-6P vertical mount connector. Refer to the table below for pin definitions:
| Number | Name | Definition | Number | Name | Definition |
|---|---|---|---|---|---|
| 1 | K- | Activation signal negative electrode | 4 | TTL-RX | UART RX, 5V |
| 2 | K+ | Activation signal positive electrode | 5 | TTL-TX | UART TX, 5V |
| 3 | GND | Negative terminal | 6 | VCC | Display power output |
4.3. Cable Diagram
The standard cable length provided is 0.5 meters. Custom lengths may be available upon request.

5. Operation
5.1. APP Operation Instructions
To configure the display via the JiKong BMS APP:
- Open the JiKong BMS APP on your device.
- Navigate to the "Parameter Setting" page.
- Change the "Serial port 3 protocol" setting to "015-JK BMS PBxx SERIES LCD Protocol V1.0".
5.2. Display Interface Operation
The display offers several interfaces for monitoring and configuration:
5.2.1. Battery Interface
This interface shows real-time data for the battery string, including:
- Current voltage (Vtg)
- Current (Cur)
- Battery capacity (Bat-Capacity in Ah)
- Remaining capacity (Rem-Capacity in Ah)
- Maximum and minimum cell voltages (Max.Cell, Min.Cell)
- Temperature (Temp)
- Power (Pwr in kW)
- Alarm status
- Charge (CHG) and Discharge (DCH) status
- Number of online battery packs (Packs)

5.2.2. Battery Pack Interface
In parallel mode, you can select individual battery packs to view their specific parameters. This interface can display up to 16 battery packs and shows:
- Battery pack design capacity
- Remaining capacity
- Charging and discharging status of each battery pack
- Voltage of each individual cell

5.2.3. Protocol Selection Interface
This interface allows you to select the appropriate communication protocols for your BMS system. You can choose between various RS485 and CAN protocols to ensure proper communication.

5.3. Multilingual Setting Demonstration
The following video demonstrates how to change the language settings on the display and navigate through the various interfaces.
6. Maintenance
To ensure optimal performance and longevity of your JIKONG 4.3-inch LCD display:
- Keep the screen clean using a soft, dry cloth. Avoid abrasive cleaners or solvents.
- Ensure proper ventilation around the display to prevent overheating.
- Avoid exposing the display to extreme temperatures or humidity outside the specified operating ranges.
- Regularly check cable connections for secure fit.
7. Troubleshooting
If you encounter issues with your display, consider the following basic troubleshooting steps:
- No Display/Power: Check the power supply voltage (9-36V) and ensure all connections are secure.
- Incorrect Data: Verify that the correct communication protocol is selected in the APP settings.
- Unresponsive Screen: Ensure the key extension interface is correctly connected and functioning, if applicable for control.
- Language Issues: Refer to the operation section for changing language settings.
For persistent issues, consult the official JIKONG support resources or the detailed user manual PDF.
8. User Tips
- When setting up, double-check the pin definitions and cable connections to avoid damage.
- Utilize the multilingual feature to set the display to your preferred language for easier monitoring.
- Familiarize yourself with the different display interfaces (Battery and Battery Pack) to quickly access relevant information about your battery system.
9. Warranty & Support
For warranty information, technical support, or service inquiries, please contact JIKONG customer service or refer to the official product documentation provided at the time of purchase. Keep your purchase receipt as proof of purchase.
A detailed user manual in PDF format is available for further reference: View User Manual (PDF)