1. Introduction
This manual provides detailed instructions for the Estardyn 2.25-inch TFT LCD module, featuring the ST7789 driver IC and a 76*284 resolution full-view SPI color screen. It covers specifications, setup, operation, maintenance, and troubleshooting to ensure optimal use of the module.
2. Specifications
The Estardyn 2.25-inch TFT LCD module is designed for various embedded applications requiring a compact color display. Key specifications are detailed below:
| Parameter | Value |
|---|---|
| Display Size | 2.25 inch |
| Resolution | 76*284 |
| Driver IC | ST7789 |
| Interface Type | 4-wire SPI |
| Display Color | Colorful |
| Power Supply | 2.8V ~ 3.3V |
| Operating Temperature | -20°C ~ 70°C |
| Linking Method | COG (Chip On Glass) |
| Module Size (PCB) | 21.08mm (W) * 73.15mm (H) |
| Display Active Area (A.A.) | 14.797mm (W) * 55.295mm (H) |
| Viewing Direction | 12 o'clock |
For detailed dimensions and pin definitions, refer to the diagrams below:


3. Setup
Before connecting the LCD module, ensure your microcontroller or development board supports 3.3V logic levels and has available SPI communication pins.
3.1 Pin Definitions
The module features an 8-pin interface. Refer to Figure 1 for the pinout. The functions are as follows:
- GND: Ground connection.
- VCC: Power supply input (2.8V - 3.3V).
- SCL: SPI Clock input.
- SDA: SPI Data input/output.
- RST: Reset pin (active low).
- DC: Data/Command selection pin (High for Data, Low for Command).
- CS: Chip Select pin (active low).
- BL: Backlight control pin (typically connected to VCC for always-on backlight, or a PWM pin for brightness control).
3.2 Connection Steps
- Power Supply: Connect the GND pin to your system's ground and the VCC pin to a stable 2.8V-3.3V power source.
- SPI Interface: Connect SCL, SDA, RST, DC, and CS pins to the corresponding SPI pins on your microcontroller. Ensure correct mapping (e.g., SCL to SCK, SDA to MOSI, etc., depending on your microcontroller's SPI configuration).
- Backlight: Connect the BL pin. For continuous backlight, connect it directly to VCC. For brightness control, connect it to a PWM-capable pin on your microcontroller.
- Verify Connections: Double-check all wiring to prevent damage to the module or your development board.
4. Operating Instructions
Operating the ST7789 LCD module typically involves using a microcontroller and a suitable display library.
4.1 Software Setup
- Microcontroller Selection: Choose a microcontroller (e.g., Arduino, ESP32, Raspberry Pi Pico) that can communicate via SPI.
- Library Installation: Install an appropriate graphics library for the ST7789 driver. Popular choices include Adafruit GFX Library and its ST7789 specific driver, or similar libraries for other platforms.
- Initialization: In your code, initialize the display with the correct resolution (76x284) and pin assignments for CS, DC, RST, and BL.
- Display Orientation: The ST7789 driver supports various display orientations. Adjust the rotation settings in your library to match your application's needs. The default viewing direction is 12 o'clock.
4.2 Basic Display Operations
- Clear Screen: Use the library's function to clear the display to a specific color (e.g., black or white).
- Draw Primitives: Utilize functions to draw pixels, lines, rectangles, circles, etc.
- Text Display: Load fonts and use text drawing functions to display characters and strings.
- Image Display: Convert images to a compatible format (e.g., bitmap arrays) and use image drawing functions to display them on the screen.
- Update Display: Some libraries require an explicit `display()` or `update()` call to push the buffered graphics data to the LCD.
5. Maintenance
Proper care and maintenance will extend the lifespan of your LCD module.
- Handling: Always handle the module by its edges. Avoid touching the display surface or the flexible printed circuit (FPC) connector.
- Cleaning: Use a soft, lint-free cloth, slightly dampened with distilled water or an LCD-safe cleaning solution, to gently wipe the display surface. Do not use abrasive cleaners or solvents.
- Storage: Store the module in an anti-static bag in a cool, dry place, away from direct sunlight and extreme temperatures.
- Environmental Conditions: Operate the module within the specified temperature range of -20°C to 70°C. Avoid high humidity and corrosive environments.
- Static Electricity: Take precautions against electrostatic discharge (ESD) when handling the module, as it can damage sensitive electronic components.
6. Troubleshooting
If you encounter issues with your LCD module, refer to the following troubleshooting steps:
- No Display/Blank Screen:
- Check power connections (VCC and GND) and ensure the power supply is within the 2.8V-3.3V range.
- Verify the backlight (BL) pin connection. If connected to VCC, ensure VCC is present. If controlled by PWM, check the PWM signal.
- Confirm all SPI connections (SCL, SDA, CS, DC, RST) are correct and secure.
- Ensure the display initialization code is executed correctly and without errors.
- Incorrect Colors/Garbled Display:
- Check the SDA (MOSI) and SCL (SCK) connections for continuity and correct wiring.
- Verify that the correct ST7789 driver library is being used and that it's configured for the 76x284 resolution.
- Ensure the data format (e.g., RGB565) used in your code matches the display's expectation.
- Display Not Responding:
- Check the RST (Reset) pin. Ensure it's toggled correctly during initialization (typically pulled low then high).
- Verify the CS (Chip Select) and DC (Data/Command) pins are being controlled correctly by your software.
- Ensure the SPI clock speed is compatible with both your microcontroller and the ST7789 driver.
- Flickering Display:
- Check power supply stability. Add decoupling capacitors near the VCC pin if necessary.
- Ensure your code is not updating the display too frequently or inefficiently.
7. User Tips
Here are some tips to enhance your experience with the Estardyn 2.25-inch TFT LCD module:
- Use Reliable Libraries: Opt for well-maintained and documented libraries (e.g., Adafruit GFX) for easier development and better compatibility.
- Start Simple: Begin with basic display functions like clearing the screen and drawing simple shapes to confirm functionality before moving to complex graphics.
- Power Supply Stability: A stable 3.3V power supply is crucial for optimal display performance and to prevent issues like flickering or instability.
- ESD Protection: Always use anti-static precautions when handling the module to prevent damage from electrostatic discharge.
- Code Optimization: For animations or fast updates, optimize your code to minimize data transfer over SPI and reduce screen tearing.
8. Warranty and Support
For specific warranty terms and conditions, please refer to the seller's policy at the time of purchase. In case of technical issues or questions not covered in this manual, please contact the Estardyn Official Store directly for support.