JIKONG JK-B2A24S30P

Contents

JIKONG JK-B2A24S30P Smart BMS User Manual

Model: JK-B2A24S30P | Brand: JIKONG

1. Introduction

The JIKONG JK-B2A24S30P Smart Battery Management System (BMS) is a sophisticated protection board designed for large-capacity series lithium battery packs. It integrates essential functions such as voltage acquisition, high-current active balancing, overcharge, over-discharge, overcurrent, over-temperature protection, coulomb metering, Bluetooth communication, and optional GPS remote capabilities.

This BMS is compatible with various battery chemistries, including Li-ion, LiFePO4, and LTO, supporting configurations from 8S to 24S with a continuous discharge current of 300A.

A key feature is its energy transfer active balancing technology, which provides a continuous 2A balance current. This technology significantly enhances battery consistency, extends battery range, and delays battery aging by efficiently transferring energy from higher-voltage cells to lower-voltage cells.

The system includes a mobile application (APP) compatible with Android and iOS, allowing users to monitor battery status, modify parameters, and control charge/discharge switches via Bluetooth. Its compact size, ease of operation, and comprehensive functionality make it suitable for a wide range of applications, including small sightseeing vehicles, mobility scooters, shared cars, high-power energy storage systems, base station backup power, and solar power stations.

JIKONG JK-B2A24S30P Smart BMS with key features highlighted
Figure 1.1: JIKONG JK-B2A24S30P Smart BMS overview, highlighting support for Li-ion/LiFePO4/LTO, active balance current 2A, built-in Bluetooth, and 8S-24S 300A capabilities.

2. Specifications

The following tables detail the general and default parameters for the JK-B2A24S30P Smart BMS.

2.1 General Parameters

ParameterValueUnit
Supply Voltage20-100V
Operating Power Consumption<1200mW
Operating Temperature-30-70°C
Maximum Number of Collection Strings24String
Maximum Balancing Current2A
Maximum Charging Current300A
Maximum Discharge Current300A
Maximum Instantaneous Current600A
Maximum Internal Loop Resistance0.21mΩ
Protective Plate Size (L*W*H)208*120.7*15.6mm
Finished Weight675g
CertificationCE, FCC, RoHS-
Balance FunctionActive Balanced BMS-
Hardware or SmartSMART BMS-
Charge and Discharge PortCommon Port BMS-
TypeLIFEPO4 Battery BMS-
Protection FunctionsOvercharge, Over Discharge, Overcurrent, Short Circuit-

2.2 Default Parameters by Battery Type

ParameterLi-ion (Ternary)LiFePO4LTOUnit
Balancing Initial Voltage332V
Maximum Balancing Current222A
Unit Overcharge Voltage4.23.62.7V
Single Overcharge Protection Recovery4.183.552.65V
Monomer Undervoltage Protection2.822.61.8V
Single Undervoltage Protection Recovery2.852.651.85V
Automatic Shutdown Voltage2.82.51.7V
SOC-0% Voltage2.92.61.85V
SOC-100% Voltage4.183.52.65V
Trigger Balancing Differential Pressure0.010.010.01V
Charging Overcurrent Protection Delay303030S
Charging Overcurrent Protection Release Time606060S
Discharge Overcurrent Protection Delay300300300S
Discharge Overcurrent Protection Release606060S
Short-circuit Protection Delay150015001500µS
Short Circuit Protection Release Time606060S
Charging Overtemperature Protection707070°C
Charging Overtemperature Restore606060°C
Discharge Overtemperature Protection707070°C
Discharge Overtemperature Recovery606060°C
Charging Low Temperature Protection-20-20-20°C
Charging Low Temperature Restore-10-10-10°C
MOS Overtemperature Protection100100100°C
MOS Overtemperature Recovery808080°C
Device Address000-
Product model, balance method, current, battery strings, type, interface, size
Figure 2.1: Key specifications of the JK-B2A24S30P BMS, including product model, balance method, balance current, charge/discharge current, battery strings, battery type, interface, and size.
Dimensions of the JK-B2A24S30P BMS
Figure 2.2: Detailed dimensions of the JK-B2A24S30P BMS, showing length, width, and thickness.

3. Packing List

Upon receiving your JIKONG JK-B2A24S30P Smart BMS, please verify that all the following components are included in the package:

  • BMS Unit (JK-B2A24S30P) x 1
  • NTC Temperature Sensor (long 400mm) x 1
  • Balance Wires (750mm) x 1 set
  • Switch (500mm) x 1
  • Packing Box x 1
  • M6 Screws x 6
Packing list for JIKONG JK-B2A24S30P BMS
Figure 3.1: Visual representation of the components included in the JK-B2A24S30P BMS package.

4. Installation and Device Activation

The JK-B2A24S-30P series protection board is suitable for 7-24 series lithium battery packs. The specific wiring method varies depending on the number of cells in your battery pack. Always ensure correct connections before powering on the BMS.

4.1 Pre-Installation Checks

Before starting the protection board, carefully check the following:

  • Verify that the balance cables are properly connected to each cell.
  • Ensure that the P- (load/charger negative) and B- (battery negative) connections are correct.
  • Confirm that the protection board is securely fixed to the battery pack.

Incorrect connections can lead to abnormal operation or severe damage to the BMS and battery.

4.2 Interface Definition

The BMS features various interfaces for connection. Refer to the following table for detailed pin definitions:

CouplerInterface NamePin No.NameDefinition
P1 (HY2.0-15P)Balance & Acquisition Interface1B-Total negative battery
2B1The first battery positive
.........
14B13The thirteenth battery positive
15B14The fourteenth battery positive
P2 (HY2.0-11P)Balance & Acquisition Interface1B15The fifteenth battery positive
.........
9B23The twenty-third battery positive
P3 (HY2.0-4P)Power & B2410B24The twenty-fourth battery positive (Total battery positive)
11B+Protection board power supply, connected to the battery B+
P3 (HY2.0-4P)Temperature Interface1T1AFirst temperature sensor pin A
2T1BFirst temperature sensor pin B
3T2ASecond temperature sensor pin A
4T2BSecond temperature sensor pin B
P4 (HY2.0-4P)4 External Temperature Interface (Optional)1T3AThird temperature sensor pin A
2T3BThird temperature sensor pin B
3T4AFourth temperature sensor pin A
4T4BFourth temperature sensor pin B
P5 (A1254WF-4A)Communication Interface (Optional)1RS485_BNegative terminal of RS485 signal
2RS485_APositive terminal of RS485 signal
3CAN_HPositive terminal of CAN signal
4CAN_LNegative terminal of CAN signal
P6 (A1254WF-2A)Buzzer Interface (Optional)1VCCBuzzer power supply positive
2GNDBuzzer power negative
P7 (1.25T-4PWT)GPS Interface1VGPSPower output, voltage close to B+
2TXUART_TX, 3.3V
P8 (A1254WF-6A)Display Interface3RXUART_RX, 3.3V
4GNDPower/signal ground
1VCCDisplay power output
2ADisplay RS485 signal positive
3BDisplay RS485 signal negative
4GNDNegative terminal
P9 (A1254WF-3A)Parallel Interface (Optional)1GNDSignal ground
2P-ENParallel module enable signal, output low level to turn on parallel module
3P-statusParallel module status signal
P10 (A1254WF-5A)ACC Interface (Optional)1ACC+ACC Positive
2ACC-ACC Negative
3NCNot connected (Empty)
4C_Detect+Charger output 12V positive
5C_Detect-Charger output 12V negative
Top view of JIKONG JK-B2A24S30P BMS showing connectors
Figure 4.1: Top view of the BMS, illustrating the layout of the main connectors and terminals.
Bottom view of JIKONG JK-B2A24S30P BMS showing balance ports
Figure 4.2: Bottom view of the BMS, showing the balance wire connection ports (B0-B24).
Detailed view of JIKONG JK-B2A24S30P BMS with balance wire connections
Figure 4.3: Detailed view of the BMS, emphasizing the balance wire connection points and their labeling.

4.3 Wiring Diagram

The following diagram illustrates the typical wiring for the JK-B2A24S-30P BMS in a 24S configuration. Ensure all connections are made accurately according to the diagram and the interface definitions.

Wiring diagram for JIKONG JK-B2A24S-30P BMS
Figure 4.4: Wiring diagram for the JK-B2A24S-30P-24S BMS, showing connections for load, charger, temperature sensors, and balance wires.

4.4 Device Activation

The protection board does not have a physical power-on control switch. It is designed for charging activation mode. After the battery assembly is completed, the BMS will activate when a charger is connected, provided the charger voltage is approximately 2V higher than the battery voltage.

Alternatively, the BMS can be activated via an optional key switch or display screen. If you have these optional accessories, simply connect them to the display interface and press the button to activate the BMS.

5. Operation and Functions

The JIKONG JK-B2A24S30P BMS offers a wide array of functions to ensure optimal battery performance and safety. These functions are managed and monitored primarily through the mobile APP.

5.1 Functional Characteristics

  • LED Bluetooth status indicator
  • APP Bluetooth remote operation
  • Battery capacity calculation
  • High precision voltage acquisition (±3mV)
  • High precision current acquisition
  • Support information screen display
  • Accurate time logging
  • Support RS485 (Optional)
  • Support CAN (Optional)
  • Support parallel function (Optional)
  • Support alarm function
  • Support heating function (Optional)
  • Support GPS communication (Optional)
  • Charge overcurrent protection
  • Charge overvoltage protection
  • Charge over temperature protection
  • Low temperature protection during charge
  • Discharge overcurrent protection
  • Discharge undervoltage protection
  • Discharge over temperature protection
  • ACC detection function
  • Short circuit protection
Functional characteristics of JIKONG JK-B2A24S30P BMS
Figure 5.1: Checklist of functional characteristics, including various protections and communication features.

5.2 Detailed Function Descriptions

5.2.1 Active Equalization

The BMS employs active balancing to transfer energy from high-voltage cells to low-voltage cells, ensuring cell consistency. Users can set the balance trigger pressure difference (mV) via the APP. Balancing automatically activates when the voltage difference between any two cells exceeds the set value and deactivates when it falls below. The default balance current is 2A. It is recommended that the balance current not exceed 0.2C of the battery capacity. If not needed, the balancing function can be turned off in the APP.

Active Balancing (Lossless Balancing) diagram
Figure 5.2: Diagram illustrating the active balancing process, where energy is transferred to achieve voltage balance with minimal energy loss.

5.2.2 GPS and Display Interface (Optional)

The BMS reserves interfaces for optional GPS modules for battery location tracking and display screens for convenient monitoring of battery information. Users can select these options based on their needs.

Rich interface options for JIKONG JK-B2A24S30P BMS
Figure 5.3: Overview of the rich interface options available, including CAN, RS485, Bluetooth, NTC, Soft Switch, SOC Indicator, Key Switch, and Active Equalizer.

5.2.3 Heating Function (Optional)

For low-temperature environments, an optional heating function can be used to warm the battery via a resistance heater or heating film, preventing reduced battery activity. The designed heating current is 10A. It is recommended to use a normally closed temperature switch (45-65°C) in series with the heating circuit as a secondary protection.

5.2.4 Alarm Function

The BMS supports an optional alarm function that provides alerts for safety risks such as overtemperature, overcharge, and overdischarge.

5.2.5 Battery Parallel Function (Optional)

This function allows for parallel connection of battery packs, suitable for energy storage applications. It requires synchronous use with parallel modules and disabling the 'charging current limiting' function in the APP.

5.2.6 ACC Detection Function

The ACC detection function enables discharge. It can be activated by applying a voltage between 20-100V across ACC+ and ACC-, or by directly short-circuiting them. A charger detection function is also available via C_detect+ and C_detect- interfaces.

5.2.7 Overvoltage Protection and Recovery

The BMS includes standard charge overvoltage protection. Users can set the single overcharge protection voltage and recovery voltage in the APP. If any cell exceeds the set overvoltage during charging, the BMS will stop charging. Charging resumes when all cell voltages fall below the recovery voltage.

5.2.8 Undervoltage Protection and Recovery

Standard discharge undervoltage protection is provided. Users can set the battery undervoltage protection voltage, recovery voltage, and automatic shutdown voltage in the APP. If any cell falls below the protection voltage during discharge, the BMS stops discharging. Discharge resumes when all cell voltages rise above the recovery voltage. The BMS will automatically shut down if any cell voltage drops below the automatic shutdown voltage.

5.2.9 Overcurrent Protection and Recovery (Charge/Discharge)

The BMS features standard charge and discharge overcurrent protection. Users can set continuous current, delay times, and release times in the APP. If the current exceeds the set value for the specified delay, protection activates. Operation resumes after the release time. The maximum continuous discharge current should not exceed 300A.

5.2.10 Overtemperature Protection and Recovery

Standard charge and discharge overtemperature protection is included. Users can set protection and recovery temperatures in the APP. If the temperature exceeds the set value, the BMS will stop the respective operation (charging or discharging). Operation resumes when the temperature falls below the recovery threshold.

5.2.11 Low Temperature Protection and Recovery

Standard charging low temperature protection is provided. Users can set protection and recovery temperatures in the APP. If the temperature falls below the set value, charging stops. Charging resumes when the temperature rises above the recovery threshold. For extremely cold areas, the optional heating function is recommended.

5.2.12 Short Circuit Protection and Recovery

The BMS is equipped with standard short circuit protection. While the trigger current is fixed, users can adjust the short circuit protection delay (µs) and recovery time (S) in the APP. If a short circuit occurs, the BMS will protect the battery and resume operation after the recovery time.

5.2.13 Emergency Switch

The emergency switch function allows the BMS to enable charge and discharge for 30 minutes in case of issues like overtemperature, overdischarge, overcharge, or cell string drops. This provides a temporary operational window to prevent critical situations.

5.2.14 Intelligent Sleep

The intelligent sleep function, configurable in the APP, reduces the BMS's power consumption during standby (charging/discharging current less than 1A for 26 consecutive hours). The BMS can be reactivated by pressing a button or connecting a charger.

5.2.15 Communication Function (Optional)

The BMS supports optional CAN and RS485 communication. Users can configure the address and communication protocol via the APP according to their specific requirements. Refer to the JIKONG Protection Board communication protocol document for details.

5.3 APP Operation Instructions

The JIKONG mobile APP allows for comprehensive monitoring and control of your BMS. To install the APP, scan the QR code below with your mobile device. Android Version 7 or higher is required.

QR code for JIKONG mobile APP download
Figure 5.4: Scan this QR code to download the JIKONG mobile APP.

Once installed, connect to the BMS via Bluetooth to access real-time data, adjust parameters, and manage functions. The APP provides a multi-screen display for clear data visualization.

JIKONG Smart BMS APP interface screenshots
Figure 5.5: Screenshots of the JIKONG Smart BMS APP interface, showing various data displays and control options for mobile, PC software, and LCD.

6. Maintenance

To ensure the longevity and optimal performance of your JIKONG Smart BMS and battery pack, follow these maintenance guidelines:

  • Regular Checks: Periodically inspect all wiring connections for tightness and signs of wear or corrosion. Ensure the BMS is securely mounted.
  • Temperature Management: Operate the BMS within its specified operating temperature range (-30°C to 70°C). If operating in extremely cold environments, consider utilizing the optional heating function to protect the battery cells.
  • Parameter Configuration: Regularly review and adjust BMS parameters via the mobile APP to match your battery's specific needs and usage patterns. Ensure protection thresholds (overcharge, undervoltage, overcurrent, overtemperature) are set appropriately.
  • Software Updates: Keep the mobile APP updated to the latest version to benefit from new features, improvements, and bug fixes.
  • Cleanliness: Keep the BMS unit clean and free from dust and debris to ensure proper heat dissipation. The fully aluminum alloy shell provides superior heat dissipation, but airflow should not be obstructed.
Fully aluminum alloy shell and heat dissipation effect
Figure 6.1: The BMS features a fully aluminum alloy shell for superior heat dissipation, crucial for maintaining performance and longevity.

7. Troubleshooting

This section provides guidance on common issues and how to address them. For complex problems, refer to the full PDF manual or contact customer support.

  • BMS Not Activating: Ensure all balance wires and main power connections (P-, B-) are correctly and securely connected. Verify that the charger voltage is at least 2V higher than the battery voltage for charging activation. If using optional key/display activation, ensure they are properly connected and the button is pressed.
  • Battery Imbalance: Check the active equalization settings in the APP. Ensure the balance trigger differential pressure is set correctly and the balancing function is enabled. Verify that the balance current is sufficient for your battery capacity (recommended <0.2C).
  • Over-Protection Triggered (Overcharge, Overdischarge, Overcurrent, Overtemperature): Review the protection parameters in the APP. Ensure they are set appropriately for your battery type and usage. Check for external factors causing the condition (e.g., faulty charger, excessive load, high ambient temperature).
  • Short Circuit Protection Triggered: If this occurs upon initial connection, check all wiring for actual short circuits. If no physical short circuit is present, the issue might be due to high inrush current from the load or charger. Adjust the short circuit protection delay time in the APP to a slightly higher value.
  • Low Temperature Issues: If the battery performance is reduced in cold weather, ensure the low temperature charging protection is not active. Consider enabling the optional heating function if available, or operating the battery in a warmer environment.
  • Communication Problems (Bluetooth/RS485/CAN): Ensure the Bluetooth connection is stable. For RS485/CAN, verify wiring, address settings, and communication protocol in the APP.
  • Emergency Situation: In critical situations (e.g., unexpected shutdown, severe imbalance), activate the emergency switch function via the APP to temporarily enable charge/discharge for 30 minutes, allowing for safe operation or relocation.

8. Warranty and Support

8.1 Service Commitment

JIKONG provides a comprehensive warranty for the JK-B2A24S30P Smart BMS. The warranty covers quality issues not caused by human factors, including functional failures and component defects, for a period of three years from the date of receipt of the goods. Our service commitment includes free repair or replacement, depending on the product's repairability evaluation results.

JIKONG Service Commitment details
Figure 8.1: JIKONG's service commitment, outlining warranty scope and after-sales process.

8.2 After-Sales Process

  1. Customer Application: Submit applications through official after-sales channels (email/online customer service), providing order numbers, fault descriptions, and evidence (photos/videos).
  2. Return of Goods: The customer is responsible for the international logistics cost of sending the product back to China and providing the waybill number for tracking purposes.
  3. Packaging Requirements: Ensure that product accessories are complete and the packaging is intact to avoid transportation damage.
  4. Detection and Processing: After receiving the product, our quality department will complete the inspection and inform the repair/replacement plan within 5-7 working days. Responsibility definition: Non-human damage: Free repair/replacement, and bear the return international logistics costs.
  5. Return and Tracking: After the repair/replacement of the product passes the quality inspection, it will be sent back to the customer through logistics, and full logistics tracking information will be provided throughout the process.

8.3 Additional Support

For a more detailed and comprehensive guide, including advanced parameter settings and specific communication protocols, please refer to the official PDF user manual: JIKONG JK-B2A24S-30P User Manual (PDF).

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.