JIKONG JK BMS B2A24S20P / JK-B2A20S20P

Contents

JIKONG JK BMS Active Balancing Protection Board User Manual

Models: JK BMS B2A24S20P / JK-B2A20S20P

1. Product Overview

The JIKONG Lithium Battery Intelligent Protection Board (BMS) is a sophisticated management system designed for large-capacity series lithium battery packs. It integrates essential functions such as voltage acquisition, high-current active balancing, overcharge, over-discharge, overcurrent, over-temperature protection, coulomb metering, Bluetooth communication, and optional GPS remote capabilities.

This BMS is suitable for various lithium battery types, including LiFePO4 and ternary lithium batteries, and is widely applicable in battery packs for small sightseeing vehicles, mobility scooters, shared cars, high-power energy storage systems, base station backup power supplies, and solar power stations.

The protection board utilizes energy transfer active balancing technology, achieving a continuous balance current of 1A or 2A. This technology ensures battery consistency, extends battery range, and delays battery aging. A dedicated mobile application (APP) for Android and iOS allows users to monitor battery status, modify parameters, and control charge/discharge switches via Bluetooth.

Front view of JIKONG JK BMS
Figure 1.1: Front view of the JIKONG JK BMS

2. Specifications

2.1. General Specifications

Attribute Value
Brand NameJIKONG
TypeLiFePO4 Battery BMS
Usage ScenarioPower BMS
Balance FunctionActive Balanced BMS
Handware or SmartSMART BMS
Charge and Discharge PortCommon Port BMS
CertificationCE, FCC, RoHS
High-concerned chemicalNone
FunctionOvercharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection

2.2. Model-Specific Parameters

The JIKONG BMS is available in 150A and 200A versions. Key parameters are detailed below:

Parameter 150A Model (JK-BxAxxS-15P) 200A Model (JK-BxAxxS-20P) Unit
Supply Voltage20-10020-100V
Operating Power Consumption<800<800mW
Operating Temperature-30-70-30-70°C
Max. Collection Strings2424String
Max. Balancing Current1A / 2A2AA
Max. Charging Current150200A
Max. Discharge Current150200A
Max. Instantaneous Current300350A
Max. Internal Loop Resistance0.650.5mΩ
Protective Plate Size (L*W*H)162*102*20.4162*102*20.4mm
Finished Weight430430g

2.3. Product Dimensions

JIKONG JK BMS Dimensions Diagram
Figure 2.1: JIKONG JK BMS Dimensions (162mm x 102mm x 20.4mm)

2.4. Default Parameters

Default parameters vary based on battery chemistry (Li-Ion, LiFePO4, LTO). These can be adjusted via the APP.

Parameter Li-Ion (Default) LiFePO4 (Default) LTO (Default) Unit
Balancing Initial Voltage332V
Max. Balancing Current1A / 2A1A / 2A1A / 2AA
Unit Overcharge Voltage4.23.62.7V
Single Overcharge Protection Recovery4.183.552.65V
Monomer Undervoltage Protection2.822.61.8V
Single Undervoltage Protection Recovery2.852.651.85V
Automatic Shutdown Voltage2.82.51.7V
SOC-0% Voltage2.92.61.85V
SOC-100% Voltage4.183.52.65V
Trigger Balancing Differential Pressure0.010.010.01V
Charging Overcurrent Protection Delay303030S
Charge Overcurrent Protection Release Time606060S
Discharge Overcurrent Protection Delay300300300S
Discharge Overcurrent Protection Release Time606060S
Short-circuit Protection Delay150015001500µS
Short-circuit Protection Release Time606060S
Charging Overtemperature Protection707070°C
Charge Overtemperature Restore Temperature606060°C
Discharge Overtemperature Protection707070°C
Discharge Overtemperature Recovery606060°C
Charging Low Temperature Protection-20-20-20°C
Charge Low Temperature Restore Temperature-10-10-10°C
MOS Overtemperature Protection100100100°C
MOS Overtemperature Recovery808080°C
Device Address000/
Discharge Precharge Time000S

3. Setup and Installation

3.1. Unpacking and Inspection

Upon receiving your JIKONG JK BMS, carefully inspect the packaging for any signs of impact or damage. Handle the protection board gently and avoid inverting it. Ensure all components listed in the packing list are present:

  • BMS Unit x1
  • NTC (400mm) x1
  • Balance Wires (750mm) x1
  • Switch (500mm) x1
  • Packing Box x1
JIKONG JK BMS Package Contents
Figure 3.1: Package Contents

3.2. Interface Definition

The BMS features various interfaces for connection and communication:

JIKONG JK BMS Interface Layout
Figure 3.2: BMS Interface Layout (CAN/RS485, GPS, Display, Heating ports)

Detailed pin definitions for the connectors are provided below. Ensure correct wiring to prevent damage.

P1 XH-15AW Connector (Balance and Acquisition Interface)

Pin Number Name Definition
1B-Total negative battery
2B1The first battery positive
3B2The second battery positive
.........
14B13The thirteenth battery positive
15B14The fourteenth battery positive

P2 XH-11AW Connector (Balance and Acquisition Interface)

Pin Number Name Definition
1B15The fifteenth battery positive
.........
7B21The twenty-first battery positive
8B22The twenty-second battery positive
9B23The twenty-third battery positive
10B24The twenty-fourth battery positive, Total battery positive
11B+Protection board power supply, connected to the battery

P3 XH-4AW Connector (Temperature Interface)

Pin Number Name Definition
1T1AFirst temperature sensor pin A
2T1BFirst temperature sensor pin B
3T2ASecond temperature sensor pin A
4T2BSecond temperature sensor pin B

P4 A1254WF-3A Connector (Communication Interface)

Pin Number Name Definition
1DNCAN_L/RS485-B signal negative
2DPCAN_H/RS485-A signal positive
3GNDSignal ground

P5 1.25T-4PWT Connector (GPS Interface)

Pin Number Name Definition
1VGPSPower output, the voltage is close to B+
2TXUART_TX, 3.3V
3RXUART_RX, 3.3V
4GNDPower/signal ground

P6 A1254WF-6A Connector (Display Interface)

Pin Number Name Definition
1VCCDisplay power output
2AThe display RS485 signal is positive
3BDisplay RS485 signal negative
4GNDNegative terminal

P7 A1254WF-7A Connector (Heating Interface)

Pin Number Name Definition
5K+Activate the positive signal
6K-Activation signal negative electrode
1HT-Heater element negative electrode
6CD+Charge indication input positive terminal
7CD-Charge indication input negative terminal

D1 Bluetooth Connection Indicator: When Bluetooth is connected to the protection board, the indicator is steady on. When the connection is disconnected, the indicator blinks.

P- Terminal: Connect to external load or negative terminal of charger.

B- Terminal: Connect to the negative battery terminal.

3.3. Wiring Diagram

The JIKONG JK BMS is compatible with 7-24 series lithium battery packs. The specific wiring method depends on the number of cells in your battery pack. A general wiring diagram for a 24S configuration is shown below. Always ensure correct polarity and connections.

JIKONG JK BMS 24S Wiring Diagram
Figure 3.3: JK-BxAxxS-15P/20P-24S Wiring Diagram

4. Operating Instructions

4.1. APP Installation and Device Activation

To utilize the full features of your JIKONG JK BMS, install the mobile APP. The APP supports Android (version 7 minimum required) and iOS operating systems. Search for "JIKONG SMART BMS" in your app store or scan the QR code provided in the product documentation (if available) to download.

JIKONG JK BMS Mobile App Interface
Figure 4.1: Mobile APP Interface for JIKONG SMART BMS

Device Activation: Before powering on the protection board, double-check that the balance cables are properly connected and that the P- and B- terminals are correctly wired. Ensure the protection board is securely fixed to the battery pack. The BMS does not have a physical power-on switch. It is designed for charging activation mode, meaning it will activate when a charger (with voltage 2V higher than battery voltage) is connected after battery assembly. For models with a display screen and button, activation can also be achieved by inserting the display cable and pressing the button.

4.2. Functional Characteristics

The JIKONG JK BMS offers a wide range of functions for optimal battery management:

  • LED Bluetooth status indicator
  • APP Bluetooth remote operation
  • Battery capacity calculation
  • High precision voltage acquisition (±3mV)
  • High precision current acquisition
  • Support information screen display
  • Accurate time logging
  • Support RS485/CAN (one of two, optional)
  • Support heating function (optional)
  • Support GPS communication (optional)
  • Discharge precharge function
  • Charge overcurrent protection
  • Charge overvoltage protection
  • Charge over temperature protection
  • Low temperature protection during charge
  • Discharge overcurrent protection
  • Discharge undervoltage protection
  • Discharge over temperature protection
  • Short circuit protection
JIKONG JK BMS Functional Characteristics
Figure 4.2: Overview of BMS Functional Characteristics

4.3. Detailed Function Descriptions

4.3.1. Active Equalization

The BMS employs active equalization to transfer energy from high-voltage cells to low-voltage cells, ensuring battery consistency. Before using this function, set basic battery parameters (battery type, cell count, capacity, trigger differential pressure, voltage/current calibration) in the APP. The default balance current is 1A/2A, adjustable via the APP. It is recommended that the balance current does not exceed 0.2C of the battery capacity. The balancing function can be enabled or disabled via the APP.

Active Balancing Principle Diagram
Figure 4.3: Active Balancing (Lossless Balancing) Principle

4.3.2. GPS and Display Interface

The BMS includes a reserved GPS port for optional GPS modules, allowing for battery location tracking. It also features a display interface for connecting an external display screen (available from JIKONG) to view battery information.

4.3.3. Heating Function (Optional)

For low-temperature environments, an optional heating function can be used with a resistance heater or heating film to warm the battery, preventing reduced activity and ensuring proper charging/discharging. The designed heating current is 4A. Users can control this function via the APP. It is recommended to install a temperature control switch (45°C to 65°C normally closed) in series as a secondary safety measure.

4.3.4. Charge Overvoltage Protection and Recovery

The BMS provides standard charge overvoltage protection. Users can set the single cell overcharge protection voltage and recovery voltage in the APP. If any cell exceeds the set voltage during charging, the BMS will stop charging. Charging resumes when all cells fall below the recovery voltage.

4.3.5. Discharge Undervoltage Protection and Recovery

Standard discharge undervoltage protection is included. Users can set the undervoltage protection voltage, recovery voltage, and automatic shutdown voltage in the APP. If any cell drops below the set undervoltage protection voltage during discharge, the BMS will trigger protection and stop discharging. Discharge resumes when all cells are above the recovery voltage. If any cell drops below the automatic shutdown voltage, the BMS will shut down to protect the battery.

4.3.6. Charge Overcurrent Protection and Recovery

The BMS features standard charge overcurrent protection. Users can set the continuous charging current, overcurrent delay, and recovery time in the APP. If the charging current exceeds the set limit for the specified delay, the BMS will stop charging. Charging resumes after the recovery time.

4.3.7. Discharge Overcurrent Protection and Recovery

Standard discharge overcurrent protection is provided. Users can set the continuous discharge current, overcurrent delay, and recovery time in the APP. If the discharge current exceeds the set limit for the specified delay, the BMS will stop discharging. Discharge resumes after the recovery time. (Note: Maximum continuous discharge current cannot exceed the nominal current of 150A/200A).

4.3.8. Overtemperature Protection and Recovery

The BMS includes standard charge and discharge overtemperature protection. Users can set protection and recovery temperatures for both charging and discharging in the APP. If the battery temperature exceeds the set limit, the BMS will stop the respective operation (charging or discharging). The operation resumes when the temperature falls below the recovery threshold.

4.3.9. Low Temperature Protection and Recovery

Standard charging low temperature protection is included. Users can set the charging low temperature protection and recovery temperatures in the APP. If the battery temperature drops below the set limit, the BMS will stop charging. Charging resumes when the temperature rises above the recovery threshold. For extremely cold areas, the optional heating function is recommended.

4.3.10. Short Circuit Protection and Recovery

The BMS is equipped with standard short circuit protection. While the trigger current is fixed, users can adjust the short circuit protection delay (µS) and recovery time (S) in the APP. If a short circuit occurs, the BMS will trigger protection. If the protection triggers upon initial connection of a charger or load, increasing the delay time may resolve it, especially if large capacitors in the load cause high inrush currents.

4.3.11. Discharge Precharge Function

The BMS includes a standard discharge precharge function with a default time of 5 seconds. Users can enable or disable this function via the APP. Setting the precharge time to 0 disables the function.

4.3.12. Emergency Switch

A standard emergency switch function is available. If issues like over-temperature, over-discharge, overcharge, or cell string drops occur during normal use, activating the emergency switch in the APP's BMS control page will enable charge and discharge for 30 minutes, providing emergency operational time. The BMS will continue to operate for this period even if a single cell reaches automatic shutdown voltage.

4.3.13. Intelligent Sleep

The BMS features an intelligent sleep function, which can be enabled or disabled via the APP. Its purpose is to put the protection board into a low-power state when idle (charging/discharging current less than 1A for 26 consecutive hours) to reduce self-consumption. The BMS can be reactivated by pressing a button (if equipped) or connecting a charger.

4.3.14. Communication Function

The BMS supports optional CAN/RS485 communication. Users can select CAN or RS485 via the APP's BMS control page. The address and communication protocol can be configured according to specific requirements. Refer to the JIKONG Protection Board communication protocol document for details.

5. Maintenance

Regular maintenance helps ensure the longevity and optimal performance of your JIKONG JK BMS:

  • Visual Inspection: Periodically check all wiring and connections for signs of wear, corrosion, or loose contacts. Ensure the BMS is securely mounted.
  • Software Monitoring: Use the JIKONG mobile APP to regularly monitor battery parameters, cell voltages, temperatures, and protection statuses. This helps identify potential issues early.
  • Parameter Review: Occasionally review the BMS parameters in the APP to ensure they are still appropriate for your battery pack's condition and usage patterns.
  • Firmware Updates: Check with JIKONG for any available firmware updates for your BMS model, which may offer improved performance or new features.
  • Cleaning: Keep the BMS unit clean and free from dust and debris to ensure proper heat dissipation. Use a soft, dry cloth for cleaning.

6. Troubleshooting

The JIKONG JK BMS is designed with multiple protection features. If the system stops functioning or exhibits abnormal behavior, check the following:

  • Protection Triggered: If the BMS stops charging or discharging, check the APP for any active protection alerts (e.g., overvoltage, undervoltage, overcurrent, overtemperature, short circuit). Address the root cause of the protection.
  • Wiring Issues: Verify all balance wires, main power cables (P- and B-), and communication cables are correctly and securely connected. Loose connections can cause erratic behavior or prevent activation.
  • Activation Failure: If the BMS does not activate after initial connection, ensure the charger voltage is at least 2V higher than the battery voltage. For models with a button, try pressing it after connecting the display.
  • APP Connectivity: If the APP cannot connect via Bluetooth, ensure Bluetooth is enabled on your device and the BMS is powered on. Try restarting the APP or the BMS.
  • Parameter Settings: Incorrect parameter settings can lead to unexpected behavior. Review your settings in the APP, especially those related to voltage, current, and temperature limits, and ensure they match your battery specifications.
  • Short Circuit Protection: If short circuit protection triggers frequently, especially upon connecting a load or charger, consider increasing the short circuit protection delay in the APP settings. Ensure there are no actual short circuits in your wiring.

For persistent issues not resolved by these steps, contact JIKONG technical support.

7. User Tips

No specific user tips from reviews or Q&A were provided for this product. However, general best practices for BMS usage include:

  • Always ensure all connections are tight and properly insulated to prevent short circuits and ensure reliable operation.
  • Regularly monitor your battery pack's health via the mobile APP, paying close attention to individual cell voltages and temperatures.
  • When configuring parameters, always refer to your battery cell manufacturer's specifications to avoid setting values that could damage your battery.
  • For systems operating in extreme temperatures, consider utilizing the optional heating function to maintain optimal battery performance and lifespan.

8. Warranty and Support

For warranty information, technical support, or service inquiries, please contact JIKONG directly or the authorized reseller from whom you purchased the product. Keep your proof of purchase for warranty claims.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.