Flipsky 75100 V2.0

Contents

Flipsky 75100 V2.0 ESC User Manual

Electronic Speed Controller for E-Skateboards, Scooters, and Ebikes

1. Introduction

The Flipsky 75100 V2.0 ESC (Electronic Speed Controller) is a high-performance, versatile speed controller designed for various electric vehicles, including e-skateboards, scooters, and ebikes. Based on the VESC platform, it offers advanced control features such as BLDC and FOC (Field-Oriented Control) modes, regenerative braking, and extensive programmability. This manual provides essential information for the safe and effective installation, operation, and maintenance of your Flipsky 75100 V2.0 ESC.

Flipsky 75100 V2.0 ESC unit with power and motor wires
Figure 1: Flipsky 75100 V2.0 ESC

Description: A black rectangular electronic speed controller with thick red and black power wires extending from one end, and three thick black motor wires from the other. Various smaller multi-colored wires and connectors are visible on the top surface.

2. Safety Information

WARNING: Improper use or installation of this product can lead to serious injury or death. Always exercise extreme caution when working with high-voltage and high-current electrical systems.

  • Always disconnect the battery before making any connections or disconnections.
  • Ensure all connections are secure and properly insulated to prevent short circuits.
  • Do not operate the ESC beyond its specified voltage and current limits.
  • Keep the ESC away from water, moisture, and extreme temperatures.
  • Professional installation is highly recommended for users unfamiliar with electronic speed controllers.
  • Always wear appropriate safety gear when testing or operating your electric vehicle.

3. Package Contents

Your Flipsky 75100 V2.0 ESC package typically includes the following items:

  • Flipsky 75100 V2.0 ESC Unit
  • USB Cable (color may vary)
  • Various connection wires and harnesses (e.g., Hall sensor wires, PPM cable, CAN bus cable)
  • Power Switch (either a button switch or a key switch, depending on the variant purchased)
Flipsky 75100 V2.0 ESC with included accessories, including a button switch
Figure 2: Typical Package Contents (with Button Switch variant shown)

Description: The Flipsky 75100 V2.0 ESC unit is shown alongside a USB cable, a round button power switch, and several bundles of multi-colored wires with various connectors. A small instruction sheet is also visible.

4. Specifications

Feature Specification
Dimensions (LxWxH) 103mm x 58mm x 24mm
Voltage Range 14-84V (4-20S LiPo)
Continuous Current 100A
Peak Current 250A
Firmware 5.02 (upgradeable; phase filter off for 5.03+)
BEC Output 5V@1.5A
Control Modes DC, BLDC, FOC (sinusoidal)
Control Interface Ports USB, CAN, UART
Supported Sensors ABI, HALL, AS5047, AS5048A
Input Set Support PPM, ADC, NRF, UART
Wire Size 12AWG
Programmable Yes
Regenerative Capacity Yes
Material Metal (Aluminum PCB)
Dimensions of the Flipsky 75100 V2.0 ESC
Figure 3: ESC Dimensions

Description: A perspective view of the ESC with blue lines indicating its dimensions: length 103mm, width 58mm, and height 18.5mm.

5. Setup and Installation

Careful wiring is crucial for the proper function and safety of your ESC. Refer to the detailed wiring diagram below and follow the steps for connection.

5.1 Wiring Diagram

Detailed wiring diagram for Flipsky 75100 V2.0 ESC
Figure 4: Detailed Wiring Diagram

Description: A comprehensive diagram showing the Flipsky 75100 V2.0 ESC and all its connection points. It illustrates connections for the motor, battery, USB, PPM, CAN+POWER, SWD, COMM, UART2, HALL sensors, and POWER SWITCH. Specific pinouts for each port are detailed. An important note advises pressing connector latches before unplugging. A smaller diagram shows how to connect a master ESC to a slave ESC via CAN bus.

5.2 Connection Steps

  1. Motor Connection: Connect the three thick motor phase wires from your motor to the corresponding outputs on the ESC. Ensure a secure connection.
  2. Battery Connection: Connect the main battery positive (red) and negative (black) wires to the designated battery terminals on the ESC. Pay close attention to polarity.
  3. Hall Sensor Connection (Port 7): If your motor uses Hall sensors for position feedback, connect the Hall sensor cable from your motor to the HALL port (7) on the ESC. The pinout is typically GND, TEMP, HALL1, HALL2, HALL3, GND, 5V.
  4. Power Switch Connection (Port 8): Connect the provided power switch (button or key type) to the POWER SWITCH port (8). The pinout includes GND, IGNITE, and BAT+.
  5. PPM Connection (Port 2): For remote control input, connect your receiver's PPM signal to the PPM port (2). The pinout is SERVO, 5V, GND.
  6. UART Connection (Port 6): For serial communication with external modules (e.g., Bluetooth module, display), connect to the UART2 port (6). Pinout: TX2, RX2, GND, 3.3V.
  7. CAN Bus Connection (Port 3): For connecting multiple ESCs in a master-slave configuration, use the CAN+POWER port (3). Pinout: GND, CANH, CANL, 5V, PWR.ON.
  8. USB Connection (Port 1): Use the provided USB cable to connect the ESC to your computer for configuration and firmware updates via the VESC Tool software.
  9. ADC Connection (Port 5): For analog input devices, connect to the ADC port (5). Pinout: ADC15, ADC2, TX/SCL, RX/SDA, ADC1, GND, 3.3V, 5V.
  10. SWD Connection (Port 4): This port is typically used for debugging and advanced development.

Important: When disconnecting any JST PH2.0 connectors, always press the small latch on the side of the connector before pulling to avoid damaging the wires or the connector itself.

6. Operation

6.1 Powering On/Off

Once all connections are securely made, turn on your electric vehicle using the connected power switch. The ESC's LED indicators (Blue, Red/Green) will provide status feedback.

6.2 Configuration with VESC Tool

The Flipsky 75100 V2.0 ESC is highly configurable using the official VESC Tool software. Connect the ESC to your computer via the USB port and launch the VESC Tool. Follow the software's instructions for motor detection, input setup (PPM, UART, etc.), and fine-tuning parameters for optimal performance.

  • Motor Detection: Essential for the ESC to learn your motor's electrical characteristics.
  • Input Setup: Configure your remote control (PPM) or other input devices.
  • Firmware Updates: Regularly check for and install the latest firmware for improved performance and features. Note that for firmware 5.03 or newer, the phase filter needs to be turned off during configuration.
  • Control Modes: Experiment with BLDC (Block Commutation) and FOC (Field-Oriented Control) modes to find the best balance of efficiency and smoothness for your application. FOC generally offers smoother and quieter operation.

7. Maintenance

  • Keep Clean and Dry: Ensure the ESC is kept free from dust, dirt, and moisture. Avoid operating in wet conditions unless the ESC is housed in a waterproof enclosure.
  • Inspect Connections: Periodically check all wiring connections for looseness, corrosion, or damage. Secure any loose connections.
  • Heat Management: Ensure adequate airflow around the ESC, especially during high-power operation, to prevent overheating. The aluminum PCB aids in heat dissipation, but proper mounting is still important.
  • Firmware: Keep the ESC firmware updated to benefit from the latest improvements and bug fixes.

8. Troubleshooting

  • No Power: Check battery connections, power switch functionality, and ensure the battery is charged.
  • Motor Not Spinning: Verify motor phase wire connections, Hall sensor connections (if used), and ensure motor detection has been successfully completed in VESC Tool. Check for error codes in VESC Tool.
  • Intermittent Operation: Inspect all signal and power connections for looseness or damage. Check for interference with control signals.
  • Overheating: Reduce load, improve ventilation, or check motor and battery parameters in VESC Tool.
  • ESC Not Connecting to VESC Tool: Ensure the USB cable is functional and properly connected. Try a different USB port or cable. Verify correct drivers are installed on your computer.
  • LED Indicators: Observe the Blue and Red/Green LEDs for diagnostic information. Refer to VESC documentation for specific LED patterns and their meanings.

For more detailed troubleshooting, consult the official VESC documentation and community forums.

9. User Tips

No specific user tips were available from reviews or Q&A for this product at the time of manual creation. However, general tips for VESC-based ESCs include:

  • Always perform a motor detection and input calibration in VESC Tool after any changes to your motor, battery, or remote control.
  • Start with conservative settings in VESC Tool and gradually increase parameters as you become familiar with the ESC's performance.
  • Consider using a Bluetooth module for convenient wireless monitoring and configuration via a mobile app.

10. Warranty and Support

For warranty information and technical support, please contact your retailer or the manufacturer directly. Keep your proof of purchase for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.