JIKONG JK BMS B2A20S20P

Contents

JIKONG JK BMS B2A20S20P/B2A24S20P Smart Active Balance Battery Management System User Manual

For Li-ion, LiFePO4, and LTO Battery Packs

1. Introduction

The JIKONG JK BMS (Battery Management System) is an intelligent protection board designed for large capacity series lithium battery packs. It features voltage acquisition, high current active balancing, overcharge, over-discharge, overcurrent, over-temperature protection, coulomb meter, Bluetooth communication, and optional GPS remote functions. This BMS is suitable for LiFePO4, ternary lithium, and LTO battery types.

It utilizes energy transfer active balancing technology with independent intellectual property rights, achieving a maximum continuous balance current of 1A/2A. This technology ensures battery consistency, improves battery range, and delays battery aging. The BMS is compact, easy to operate, and full-featured, making it ideal for various applications including small sightseeing vehicles, mobility scooters, shared cars, high-power energy storage, base station backup power supplies, and solar power stations.

A mobile APP is available for Android and iOS operating systems, allowing users to connect via Bluetooth to monitor battery status, modify working parameters, and control charge/discharge switches.

Functional Characteristics

  • LED Bluetooth status indicator
  • APP Bluetooth remote operation
  • Battery capacity calculation
  • High precision voltage acquisition (±3mV)
  • High precision current acquisition
  • Support information screen display
  • Accurate time logging
  • Support RS485/CAN (one of two)
  • Support heating function
  • Support GPS communication
  • Discharge precharge function
  • Charge overcurrent protection
  • Charge overvoltage protection
  • Charge over temperature protection
  • Low temperature protection during charge
  • Discharge overcurrent protection
  • Discharge undervoltage protection
  • Discharge over temperature protection
  • Short circuit protection
Diagram showing functional characteristics of JIKONG BMS

Figure 1: Functional Characteristics Overview

2. Package Contents

Upon opening the package, please verify that all items are present and undamaged. The standard package includes:

  • BMS Unit (x1)
  • NTC Temperature Sensor (400mm) (x1)
  • Balance Wires (750mm) (x1)
  • Switch (500mm) (x1)
  • Packing Box (x1)
Image showing the contents of the JIKONG BMS package: BMS unit, NTC temperature sensor, balance wires, switch, and packing box.

Figure 2: Package Contents

Video 1: Product Unboxing and Initial Overview

3. Specifications

3.1. General Parameters (200A Protection Board)

ParameterValueUnit
Supply Voltage20-100V
Operating Power Consumption<800mW
Operating Temperature-30 to 70°C
Max. Collection Strings24Strings
Max. Balancing Current2A
Max. Charging Current200A
Max. Discharge Current200A
Max. Instantaneous Current350A
Max. Internal Loop Resistance0.5mΩ
Protection Board Size (L*W*H)162*102*20.4mm
Finished Weight430g

3.2. Default Parameters

ParameterLi-ion (Default)LiFePO4 (Default)LTO (Default)Unit
Balancing Initial Voltage332V
Max. Balancing Current1 (or 2)1 (or 2)1 (or 2)A
Unit Overcharge Voltage4.23.62.7V
Single Overcharge Protection Recovery4.183.552.65V
Monomer Undervoltage Protection2.822.61.8V
Single Undervoltage Protection Recovery2.852.651.85V
Automatic Shutdown Voltage2.82.51.7V
SOC-0% Voltage2.92.61.85V
SOC-100% Voltage4.183.52.65V
Trigger Balancing Differential Pressure0.010.010.01V
Charging Overcurrent Protection Delay3030S
Charge Overcurrent Protection Release Time6060S
Discharge Overcurrent Protection Delay300300300S
Discharge Overcurrent Protection Release Time606060S
Short-circuit Protection Delay150015001500uS
Short-circuit Protection Release Time606060S
Charging Overtemperature Protection707070°C
Charge Overtemperature Restore Temperature606060°C
Discharge Overtemperature Protection707070°C
Discharge Overtemperature Recovery606060°C
Charging Low Temperature Protection-20-20-20°C
Charge Low Temperature Restore Temperature-10-10-10°C
MOS Overtemperature Protection100100100°C
MOS Overtemperature Protection Recovery808080°C
Device Address000/
Discharge Precharge Time000S
Dimensions of the JIKONG BMS unit

Figure 3: BMS Dimensions (162mm x 102mm x 20.4mm)

4. Setup and Installation

4.1. Pre-installation Checks

  • Handle the packaging box and the protection board gently. Avoid dropping or inverting.
  • Before unpacking, check if the package is intact and free from impact marks or damage.
  • Ensure the balance cable is properly connected and that the P- and B- terminals are correctly connected.
  • Verify that the protection board is securely fixed to the battery core.

4.2. Wiring Diagram

The JK-BxAxxS-15P/20P series protection board is suitable for 7-24 series lithium battery packs. The wiring method varies depending on the number of cells in your battery pack. A general wiring diagram is provided below. For specific configurations, refer to the detailed wiring instructions in the official PDF manual.

Wiring diagram for JIKONG BMS BxAxxS-15P/20P-24S

Figure 4: General Wiring Diagram for JK-BxAxxS-15P/20P-24S

4.3. Interface Definition

The BMS features various interfaces for communication and control:

Diagram showing rich interfaces of JIKONG BMS

Figure 5: BMS Interfaces (CAN, RS485, BT, NTC, Soft Switch, SOC Indicator, Key Switch, Active Equalizer)

P1 (XH-15AW) - Balance and Acquisition Interface:

Pin No.NameDescription
1B-Total negative battery
2-24B1-B23Positive terminal of battery cells 1 to 23

P2 (XH-11AW) - Additional Balance Interface (for higher cell counts):

Pin No.NameDescription
1-7B15-B21Positive terminal of battery cells 15 to 21 (for 20S/24S models)

P3 (XH-4AW) - Temperature Interface:

Pin No.NameDescription
1T1AFirst temperature sensor pin A
2T1BFirst temperature sensor pin B
3T2ASecond temperature sensor pin A
4T2BSecond temperature sensor pin B

P4 (A1254WF-3A) - Communication Interface:

Pin No.NameDescription
1DNCAN_L/RS485-B signal negative
2DPCAN_H/RS485-A signal positive
3GNDSignal ground

P5 (1.25T-4PWT) - GPS Interface:

Pin No.NameDescription
1VGPSPower output, voltage close to B+
2TXUART TX, 3.3V
3RXUART RX, 3.3V
4GNDPower/signal ground

P6 (A1254WF-6A) - Display Interface:

Pin No.NameDescription
1VCCDisplay power output
2ADisplay RS485 signal positive
3BDisplay RS485 signal negative
4GNDNegative terminal

P7 (A1254WT-7A) - Heating Interface:

Pin No.NameDescription
1-5HT-Heater element negative electrode
6CD+Charge indication input positive terminal
7CD-Charge indication input negative terminal

D1 - Bluetooth Connection Indicator: When Bluetooth is connected to the protection board, the indicator is steady on. When the connection is disconnected, the indicator blinks.

P- Terminal: Connect to external load or negative terminal of charger.

B- Terminal: Connect to the negative battery terminal.

5. Operation

5.1. APP Installation

The mobile APP for the JIKONG BMS can be obtained by scanning the QR code below. An Android Version 7 minimum is required for the Android APP.

QR code for JIKONG BMS APP download

Figure 6: APP Download QR Code

For detailed instructions, please refer to the User Manual (PDF).

5.2. Device Activation

Before powering on the protection board, double-check all wiring, especially the balance cable connections and P-/B- terminals. Ensure the BMS is securely mounted to the battery. Incorrect connections can lead to abnormal operation or damage.

The protection board does not have a physical power-on switch. It is designed for charging activation mode. To activate, connect a charger with a voltage 2V higher than the battery voltage to the battery pack. The BMS will power on automatically.

Alternatively, if you have an optional display screen and button, you can activate the BMS by connecting the cable to the display interface and pressing the button.

5.3. Parameter Setting

All parameters, such as overcharge/undervoltage protection thresholds, balancing current, and temperature limits, can be configured via the mobile APP. Refer to the "Instructions for Setting Protection Board Parameters" in the full user manual for detailed guidance.

Video 2: APP Interface and Parameter Adjustment Demonstration

5.4. Active Equalization

The BMS employs active equalization to transfer energy from higher voltage cells to lower voltage cells, maintaining battery consistency. Before using this function, set the battery type and basic parameters (number of cells, battery capacity, trigger equalization differential pressure, voltage calibration, current calibration) in the APP. The default balance current is 1A/2A, adjustable based on battery capacity (recommended not to exceed 0.2C of battery capacity). The balancing function can be turned off via the BMS control page in the APP if not needed.

5.5. Heating Function (Optional)

If equipped with the optional heating function, the BMS can heat the battery at low temperatures using a resistance heater or heating film. This prevents reduced battery activity and ensures proper charging/discharging. The designed heating current is 4A. Users can control this function via the APP. It is recommended to install a temperature control switch (45°C to 65°C normally closed type) in series with the heating circuit for secondary protection against thermal runaway.

5.6. Discharge Precharge Function

The BMS includes a discharge precharge function with a default time of 5 seconds. This can be enabled or disabled as needed. Setting the precharge time to 0 disables the function.

5.7. Intelligent Sleep

The intelligent sleep function is standard. It closes the protection board when in standby (charging/discharging current less than 1A for 26 consecutive hours) to reduce energy consumption. To reactivate, press the button (if equipped) or connect a charger.

6. Protection Features

The JIKONG BMS provides comprehensive protection for your battery pack:

  • Charge Overvoltage Protection: Prevents overcharging of individual cells. The BMS will stop charging if any cell exceeds the set overvoltage threshold and resume when all cells are below the recovery voltage.
  • Discharge Undervoltage Protection: Prevents over-discharging. The BMS will stop discharging if any cell falls below the set undervoltage threshold and resume when all cells are above the recovery voltage. An automatic shutdown voltage is also set for critical low voltage.
  • Charge Overcurrent Protection: Protects against excessive charging current. Charging will be stopped if the current exceeds the set limit for a specified delay and resume after the release time.
  • Discharge Overcurrent Protection: Protects against excessive discharging current. Discharging will be stopped if the current exceeds the set limit for a specified delay and resume after the release time. (Note: Max continuous discharge current should not exceed 150A/200A nominal current).
  • Over Temperature Protection: Protects against high temperatures during charge and discharge. The BMS will stop operation if the temperature exceeds the set limit and resume when it falls below the recovery temperature.
  • Low Temperature Protection: Protects against low temperatures during charge. Charging will be stopped if the temperature falls below the set limit and resume when it rises above the recovery temperature.
  • Short Circuit Protection: Automatically triggers upon short circuit events. The delay and recovery time can be adjusted via the APP. If a short circuit occurs during initial connection of a charger or load, increasing the delay time may resolve it due to peak current spikes.
  • Emergency Switch: In case of critical issues like over-temperature, over-discharge, over-charge, or cell imbalance, activating the emergency switch in the APP will force the BMS to operate for 30 minutes, providing an emergency usage window even if individual cells reach automatic shutdown voltage.

7. Maintenance

  • Regularly check all wiring connections for tightness and corrosion.
  • Keep the BMS unit clean and free from dust and moisture.
  • Monitor battery cell voltages and temperatures via the APP to ensure optimal performance.
  • If the optional heating function is installed, periodically check the heating element and temperature control switch.
  • Refer to the APP for any diagnostic information or error codes.

8. Troubleshooting

  • BMS not powering on: Ensure all connections are correct, especially balance cables and P-/B- terminals. Activate by connecting a charger (voltage 2V higher than battery) or using the optional activation button/display.
  • Battery imbalance: Verify active equalization is enabled in the APP and parameters are set correctly. Check individual cell voltages for significant discrepancies.
  • Protection triggered (e.g., overvoltage, overcurrent): Check the corresponding parameters in the APP. Ensure the battery pack is within safe operating limits. For short circuits, check external wiring for faults.
  • APP connection issues: Ensure Bluetooth is enabled on your mobile device and the BMS. Try restarting the APP and the BMS. Verify the APP version is compatible (Android 7 minimum).
  • Heating not working (optional): Check the heating function is enabled in the APP. Inspect the heating element and temperature control switch for faults.

9. User Tips

  • Initial Setup: Always double-check all wiring before applying power to prevent damage. Pay close attention to the balance wire order.
  • APP Customization: Take advantage of the APP's parameter settings to fine-tune the BMS to your specific battery chemistry and usage patterns.
  • Cold Weather Operation: If operating in cold environments, consider using the optional heating function to maintain battery performance and longevity.
  • Monitoring: Regularly monitor your battery's health through the APP, paying attention to cell voltages and temperatures, to catch potential issues early.
  • Firmware Updates: Check the official JIKONG website or APP for any available firmware updates to ensure optimal performance and access to new features.

10. Warranty and Support

10.1. Service Commitment

JIKONG provides a 3-year warranty from the date of receipt of the goods. This warranty covers global warranty services for quality issues not caused by human factors (including functional failures, component defects, etc.).

Service Form: Support free repair or replacement, depending on the product's repairability evaluation results.

10.2. After-Sales Process

  1. Customer Application: Customers submit applications through official after-sales channels (email/online customer service), providing order numbers, fault descriptions, and evidence (photos/videos).
  2. Return of Goods: The customer pays for the international logistics cost of sending the product back to China.
  3. Packaging Requirements: Ensure that the product accessories are complete and the packaging is intact to avoid transportation damage.
  4. Detection and Processing: After receiving the product, our quality department will complete the inspection and inform the repair/replacement plan within 5-7 working days. Responsibility definition: Non-human damage: Free repair/replacement.

For further assistance or to view the full user manual, please visit the official JIKONG website or refer to the provided PDF document: JIKONG Lithium Battery Active Balance Protection Board Maintenance Manual (PDF).

Image detailing JIKONG's service commitment and after-sales process

Figure 7: Service Commitment and After-Sales Process

Certifications for JIKONG products including CE, FCC, RoHS

Figure 8: Product Certifications (CE, FCC, RoHS)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.