JIKONG JK-BxAxxS-15P/20P

Contents

JIKONG JK BMS Lithium Battery Active Balancing Protection Board User Manual

Model: JK-BxAxxS-15P/20P

Brand: JIKONG

1. Introduction

The JIKONG JK BMS (Battery Management System) is an intelligent protection board designed for large capacity series lithium battery packs. It integrates advanced features such as voltage acquisition, high current active balancing, and comprehensive protection mechanisms.

This BMS is compatible with various lithium battery types, including Li-ion, LiFePO4, and LTO (Lithium Titanate Oxide) batteries, making it suitable for a wide range of applications from small sightseeing vehicles to high-power energy storage systems.

Key features include:

  • Support for Li-ion/LiFePO4/LTO battery types
  • Built-in Bluetooth for APP monitoring and control
  • Active Balance Current up to 1A or 2A (model dependent)
  • Supports 8S-24S series battery configurations
  • Continuous charging/discharging current up to 150A or 200A (model dependent)
  • Comprehensive protection functions: Overcharge, Over-discharge, Overcurrent, Overtemperature, Low Temperature, and Short Circuit protection.
  • Optional GPS and display interfaces
  • Heating function for low-temperature environments

The protection board utilizes energy transfer active balancing technology with independent intellectual property rights, ensuring maximum battery consistency, extended battery range, and delayed battery aging.

A mobile APP is available for both Android and iOS operating systems, allowing users to connect via Bluetooth to monitor battery status, modify parameters, and control charge/discharge switches.

2. Package Contents

Upon unpacking, please verify that all components are present and in good condition. The package should contain the following items:

  • 1 x JIKONG JK BMS Unit
  • 1 x NTC Temperature Sensor (400mm length)
  • 1 set x Balance Wires (750mm length)
  • 1 x Switch (500mm length)
  • 1 x Packing Box
JIKONG JK BMS package contents including the BMS unit, NTC temperature sensor, balance wires, switch, and packing box.
Figure 2.1: Package Contents. Includes the BMS unit, NTC temperature sensor, balance wires, switch, and packing box.

The BMS unit itself features a robust aluminum alloy casing for superior heat dissipation.

Exploded view of the JIKONG JK BMS showing internal components and aluminum casing for heat dissipation.
Figure 2.2: Exploded view of the BMS, highlighting the aluminum alloy shell and internal components designed for efficient heat dissipation.

3. Specifications

The JIKONG JK BMS is available in different configurations, primarily distinguished by their continuous current rating and cell count support. The following tables detail the general and default parameters.

3.1. General Parameters (150A Protection Board)

ParameterValueUnit
Supply Voltage20-100V
Operating Power Consumption<800mW
Operating Temperature-30 to 70°C
Max. Number of Collection Strings24Strings
Max. Balancing Current1A or 2AA
Max. Charging Current150A
Max. Discharge Current150A
Max. Instantaneous Current300A
Max. Internal Loop Resistance0.65mΩ
Protective Plate Size (L×W×H)162×102×20.4mm
Finished Weight430g

3.2. General Parameters (200A Protection Board)

ParameterValueUnit
Supply Voltage20-100V
Operating Power Consumption<800mW
Operating Temperature-30 to 70°C
Max. Number of Collection Strings24Strings
Max. Balancing Current2A
Max. Charging Current200A
Max. Discharge Current200A
Max. Instantaneous Current350A
Max. Internal Loop Resistance0.5mΩ
Protective Plate Size (L×W×H)162×102×20.4mm
Finished Weight430g

3.3. Default Parameters

The following table outlines the default parameter settings for various battery types. These can be adjusted via the APP.

ParameterLi-ion (Default)LiFePO4 (Default)LTO (Default)Unit
Balancing Initial Voltage332V
Max. Balancing Current1 or 21 or 21 or 2A
Unit Overcharge Voltage4.23.62.7V
Single Overcharge Protection Recovery4.183.552.65V
Monomer Undervoltage Protection2.822.61.8V
Single Undervoltage Protection Recovery2.852.651.85V
Automatic Shutdown Voltage2.82.51.7V
SOC-0% Voltage2.92.61.85V
SOC-100% Voltage4.183.52.65V
Trigger Balancing Differential Pressure0.010.010.01V
Charging Overcurrent Protection Delay303030S
Charge Overcurrent Release Time606060S
Discharge Overcurrent Protection Delay300300300S
Discharge Overcurrent Release Time606060S
Short-circuit Protection Delay150015001500µS
Short Circuit Release Time606060S
Charging Overtemperature Protection707070°C
Charge Overtemperature Restore Temperature606060°C
Discharge Overtemperature Protection707070°C
Discharge Overtemperature Recovery606060°C
Charging Low Temperature Protection-20-20-20°C
Charge Low Temperature Restore Temperature-10-10-10°C
MOS Overtemperature Protection100100100°C
MOS Overtemperature Protection Recovery808080°C
Device Address000/
Discharge Precharge Time000S
Dimensions of the JIKONG JK BMS unit: 162mm length, 102mm width, 20.4mm height.
Figure 3.1: Product Dimensions (162mm x 102mm x 20.4mm).

4. Installation and Wiring

4.1. Unpacking and Precautions

Handle the packaging and the protection board gently. Avoid dropping or inverting the unit. Before opening, inspect the package for any signs of impact or damage. Ensure the protection board is securely fixed to the battery core before powering on.

4.2. Wiring Diagram

The JIKONG JK BMS supports 7-24 series lithium battery packs. The wiring method varies depending on the number of cells in your battery pack. Always ensure that the balance cables are correctly connected and that the P- and B- terminals are properly wired.

Wiring diagram for JIKONG JK BMS supporting 8S-24S series batteries, showing connections for P-, B-, and balance wires.
Figure 4.1: General Wiring Diagram for 8S-24S Series Batteries. This diagram illustrates the connections for the BMS, including P- (load/charger negative), B- (battery negative), and the balance wires (B1 to B24).
Diagram showing the rich interface of the JIKONG JK BMS, including CAN, RS485, BT, NTC, Soft Switch, SOC Indicator, Key Switch, and Active Equalizer ports.
Figure 4.2: Rich Interface Diagram. The BMS offers multiple communication and control interfaces such as CAN, RS485, Bluetooth (BT), NTC temperature sensor, soft switch, SOC indicator, key switch, and active equalizer.

4.3. Connector Pin Definitions

The following tables detail the pin definitions for the various connectors on the JIKONG JK BMS.

P1 (XH-15AW) - Balance and Acquisition Interface

Pin No.NameDescription
1B-Total negative battery
2B1The first battery positive
.........
14B13The thirteenth battery positive
15B14The fourteenth battery positive

P2 (XH-11AW) - Balance and Acquisition Interface (Extended)

Pin No.NameDescription
1B15The fifteenth battery positive
.........
7B21The twenty-first battery positive
8B22The twenty-second battery positive
9B23The twenty-third battery positive
10B24The twenty-fourth battery positive (Total battery positive)
11B+Protection board power supply, connected to the battery

P3 (XH-4AW) - Temperature Interface

Pin No.NameDescription
1T1AFirst temperature sensor pin A
2T1BFirst temperature sensor pin B
3T2ASecond temperature sensor pin A
4T2BSecond temperature sensor pin B

P4 (A1254WF-3A) - Communication Interface

Pin No.NameDescription
1DNCAN_L/RS485-B signal negative
2DPCAN_H/RS485-A signal positive
3GNDSignal ground

P5 (1.25T-4PWT) - GPS Interface

Pin No.NameDescription
1VGPSPower output, voltage close to B+
2TXUART TX, 3.3V
3RXUART RX, 3.3V
4GNDPower/signal ground

P6 (A1254WF-6A) - Display Interface

Pin No.NameDescription
1VCCDisplay power output
2ADisplay RS485 signal positive
3BDisplay RS485 signal negative
4GNDNegative terminal

P7 (A1254WF-7A) - Heating Interface

Pin No.NameDescription
5K+Activate the positive signal
6K-Activation signal negative electrode
1-4HT-Heater element negative electrode
6CD+Charge indication input positive terminal
7CD-Charge indication input negative terminal

4.4. Bluetooth Connection Indicator (D1)

The Bluetooth connection indicator (D1) on the BMS unit will be steady on when connected to the protection board and will blink when disconnected.

5. Operation

5.1. APP Installation

The JIKONG BMS features a mobile application for both Android (version 7 minimum required) and iOS devices. To install the APP, scan the QR code below:

QR code for JIKONG BMS mobile APP download.
Figure 5.1: Scan this QR code to download the JIKONG BMS mobile APP.

The APP allows for comprehensive monitoring and control of your BMS. It displays real-time data such as cell voltages, temperatures, current, and various protection statuses. You can also modify parameters and control functions like charge/discharge switches.

Screenshots of the JIKONG BMS mobile APP and PC software interface, showing data monitoring and control options.
Figure 5.2: Multi-screen display and data connection. The JIKONG Smart BMS APP supports iOS/Android/HarmonyOS, providing real-time data and control options. PC software and an optional LCD display are also available.

5.2. Device Activation

Before powering on the protection board, double-check that all balance cables are correctly connected and that the P- and B- terminals are properly wired. Ensure the protection board is securely fixed to the battery cells. Failure to do so may result in abnormal operation or severe damage.

The BMS does not have a power-on control switch. It is designed for charging activation. After the battery assembly is complete, connect a charger (with a voltage 2V higher than the battery voltage) to activate the protection board. Alternatively, if you have an optional display screen and button, you can activate the BMS by inserting the cable into the display interface and pressing the button.

5.3. Parameter Settings

All parameters, including protection thresholds and balancing settings, can be configured through the mobile APP. Refer to the 'Parameter Setting' section within the APP for detailed instructions on adjusting these values. For initial parameter changes, an authorization password may be required.

Video 5.1: Demonstration of JIKONG BMS APP usage, including unboxing, connecting to the APP, viewing real-time data, and adjusting parameters. The video shows how to download the APP, connect via Bluetooth, and navigate through the interface to monitor cell voltages and modify settings like charge/discharge switches and balance functions.

6. Advanced Features and Protections

The JIKONG JK BMS offers a comprehensive suite of features to ensure the safety and longevity of your battery pack.

List of functional characteristics of the JIKONG JK BMS, including LED Bluetooth status, APP remote operation, battery capacity calculation, high precision voltage/current acquisition, information screen display, accurate time logging, RS485/CAN support, heating function, GPS communication, discharge precharge, and various charge/discharge protections.
Figure 6.1: Functional Characteristics. The BMS provides LED Bluetooth status indication, APP remote operation, battery capacity calculation, high precision voltage and current acquisition, information screen display, accurate time logging, support for RS485/CAN, heating function, GPS communication, discharge precharge function, and comprehensive charge/discharge protection features.

6.1. Active Equalization

The BMS employs active balancing technology to transfer energy from higher voltage cells to lower voltage cells, ensuring uniform cell voltage across the battery pack. This process maximizes battery consistency, extends battery life, and improves overall performance. The balancing current can be set via the APP, with a default of 1A or 2A depending on the model. It is recommended that the balance current does not exceed 0.2C of the battery capacity.

Diagram illustrating active balancing, showing energy transfer between battery cells to achieve voltage balance.
Figure 6.2: Active Balancing (Lossless Balancing). This diagram visually represents how active balancing works by transferring energy from cells with higher voltage to those with lower voltage, ensuring minimal energy loss and achieving voltage balance.

6.2. Heating Function

For low-temperature environments, the BMS supports an optional heating function. This uses a resistance heater or heating film to warm the battery, preventing reduced activity and ensuring proper charge/discharge performance. The heating current is 4A. Users can switch this function on/off via the APP based on ambient temperature. It is recommended to install a temperature control switch (45°C to 65°C normally closed type) in series with the heating circuit as a secondary safety measure.6.3. Overvoltage Protection and Recovery

The BMS includes standard charge overvoltage protection. If any cell's voltage exceeds the set overvoltage protection threshold during charging, the BMS will halt charging. Charging will resume once all cell voltages drop below the recovery threshold, preventing cell damage from overcharging.

6.4. Undervoltage Protection and Recovery

Standard discharge undervoltage protection is provided. If any cell's voltage falls below the set undervoltage protection threshold during discharge, the BMS will cut off discharge to protect the cells from over-discharge damage. Discharge will resume once all cell voltages rise above the recovery threshold. If a cell's voltage drops below the automatic shutdown voltage, the BMS will shut down completely.

6.5. Overcurrent Protection and Recovery

The BMS features standard charge and discharge overcurrent protection. If the charging or discharging current exceeds the set continuous current for a specified delay, the BMS will activate protection. It will recover after a set release time. Note that the maximum continuous discharge current should not exceed the nominal current of 150A/200A.

6.6. Overtemperature and Low Temperature Protection

The BMS includes standard charge and discharge overtemperature protection, as well as charge low temperature protection. Users can set the temperature thresholds and recovery values via the APP. If temperatures exceed or fall below these thresholds, the BMS will activate protection and recover once temperatures return to safe operating ranges. For extremely cold areas, using the heating function is recommended to protect battery cells.6.7. Short Circuit Protection and Recovery

Standard short circuit protection is built-in. The BMS will automatically trigger short circuit protection if a short is detected. Users can adjust the short circuit protection delay and recovery time via the APP. If a short circuit occurs during initial connection of a charger or load, increasing the delay time may resolve the issue, especially with loads that have large capacitance and high instantaneous startup currents.6.8. Discharge Precharge Function

The BMS includes a discharge precharge function with a default time of 5 seconds. This can be enabled or disabled as needed. Setting the precharge time to 0 disables the function.6.9. Emergency Switch

In case of issues like over-temperature, over-discharge, or over-charge during normal use, activating the emergency switch via the APP's BMS control page will enable charge and discharge for 30 minutes. This provides a temporary operational window, even if a single cell voltage reaches the automatic shutdown level, preventing critical failures in situations like being stranded on the road.6.10. Intelligent Sleep

The intelligent sleep function is standard. When the BMS is in standby (charging and discharging current less than 1A for 26 consecutive hours), it will enter sleep mode to reduce its own energy consumption. To reactivate, press the physical button or connect a charger.6.11. Communication Functions (CAN/RS485/GPS)

The BMS supports optional CAN and RS485 communication. Users can select between CAN or RS485 for multiplexed ports on the APP's BMS control page. The BMS also reserves a GPS port for connecting a GPS device, allowing for battery location tracking.

7. Application Scenarios

The JIKONG JK BMS is suitable for a wide range of applications involving power lithium batteries, storage lithium batteries, and outdoor batteries. Common applications include:

  • E-bikes
  • Electric Tricycles
  • Low Speed Quads
  • Forklifts
  • Cleaning Cars
  • Tourist Cars
  • Industrial Drones
  • Scooters
  • RV Energy Storage
  • General Lithium Battery Packs
  • Power Banks
  • Storage Batteries
Various application scenarios for the JIKONG JK BMS, including e-bikes, electric tricycles, forklifts, industrial drones, RV energy storage, and power banks.
Figure 7.1: Wide Application Scenarios. The JIKONG BMS is suitable for power lithium batteries, storage lithium batteries, outdoor batteries, and other major application scenarios.

8. User Tips

Based on common user inquiries, here are some tips for optimal use:

  • Battery Configuration: When connecting to a battery bank, especially with multiple rows of cells (e.g., 3 rows of 15 cells for a 48V 300Ah system), ensure you follow the specific wiring diagram for your total series cell count (S-count). The BMS supports 7S-24S configurations. Refer to the 'Product Adaptation Guide' in Section 3.3 and the detailed wiring diagram in Section 4.2.
  • APP Password: The default password for the APP is typically "1234". You can change this within the APP settings.
  • Parameter Modification: For the first time modifying parameters in the APP, you will need to enter an authorization password.
  • Balance Function: If you need to adjust the balance current, ensure it does not exceed 0.2C of your battery capacity to prevent excessive stress on the cells.

9. Troubleshooting

This section provides general guidance for common issues. For detailed diagnostics, refer to the APP's real-time status and alarm logs.

9.1. BMS Not Activating

  • Check Wiring: Ensure all balance cables, P-, and B- connections are correct and secure.
  • Secure Mounting: Verify the BMS is firmly fixed to the battery pack.
  • Charging Activation: If the BMS does not have a physical power switch, connect a charger with a voltage 2V higher than the battery pack voltage to activate it.
  • Button/Display Activation: If equipped with an optional display and button, ensure the cable is inserted and press the button to activate.

9.2. Frequent Protection Triggers

  • Overcurrent Protection: If short circuit protection triggers upon initial connection of a charger or load, consider increasing the short circuit protection delay in the APP. This can compensate for high instantaneous currents from large capacitive loads.
  • Temperature Protection: If overtemperature or low temperature protections are frequently triggered, check the ambient operating conditions. For low temperatures, consider using the optional heating function. Ensure NTC sensors are correctly placed.
  • Voltage Protection: If overvoltage or undervoltage protections are frequent, verify cell balance and battery health. Adjust protection thresholds in the APP if necessary, ensuring they are within safe limits for your battery chemistry.

9.3. APP Connection Issues

  • Bluetooth: Ensure Bluetooth is enabled on your mobile device and the BMS. The D1 indicator should be steady on when connected.
  • APP Version: Make sure you have the latest version of the JIKONG BMS APP installed.
  • Compatibility: Verify your mobile device's operating system meets the minimum requirements (Android 7+).

10. Maintenance

Regular maintenance helps ensure the longevity and optimal performance of your JIKONG JK BMS.

  • Visual Inspection: Periodically inspect the BMS and its connections for any signs of physical damage, corrosion, or loose wiring.
  • Cleanliness: Keep the BMS unit clean and free from dust and debris to ensure proper heat dissipation.
  • Firmware Updates: Check the JIKONG website or APP for any available firmware updates to ensure your BMS has the latest features and bug fixes.
  • Parameter Review: Periodically review your APP parameter settings to ensure they are still appropriate for your battery pack's condition and usage patterns.
  • Temperature Monitoring: Regularly monitor battery and BMS temperatures, especially during charging and discharging, to ensure they remain within safe operating limits.

11. Warranty and Support

11.1. Service Commitment

JIKONG provides a 3-year warranty from the date of receipt of the goods. The warranty covers quality issues not caused by human factors (including functional failures, component defects, etc.).

After-Sales Process:

  1. Customer Application: Submit applications through official after-sales channels (email/online customer service), providing order numbers, fault descriptions, and evidence (photos/videos).
  2. Return of Goods: The customer is responsible for the international logistics cost of sending the product back to China and providing the waybill number for tracking purposes.
  3. Packaging Requirements: Ensure that the product accessories are complete and the packaging is intact to avoid transportation damage.
  4. Detection and Processing: After receiving the product, our quality department will complete the inspection and inform the repair/replacement plan within 5-7 working days. Responsibility definition: Non-human damage: Free repair/replacement, and the seller bears the return international logistics costs.
  5. Return and Tracking: After the repair/replacement passes the quality inspection, it will be sent back to the customer through logistics, and full logistics tracking information will be provided throughout the process. Time commitment: The return logistics cycle is controlled within 7-15 working days (may fluctuate due to customs clearance and other factors). Cross-border compliance: Customers need to cooperate in providing necessary customs declaration documents (such as original purchase vouchers, repair statements) to avoid customs clearance delays.

11.2. Additional Support

For further assistance, please refer to the official JIKONG website or contact their customer service. You can also find additional instructional videos and detailed communication protocol documents there.

A user manual in PDF format is available for download: JIKONG BMS User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.