XTOOL InPlus IP919

Contents

XTOOL InPlus IP919 Smart Diagnostic Tool User Manual

Comprehensive guide for setup, operation, and maintenance.

1. Introduction

The XTOOL InPlus IP919 Diagnostic Tool is designed to interface with a vehicle's Electronic Control Unit (ECU) to retrieve diagnostic trouble codes (DTCs), access data stream information, and command active tests (bi-directional control tests). It supports diagnostics for various vehicle control systems including engine, transmission, anti-lock brake system (ABS), SRS (Airbag) system, chassis, and body. The tool can graph up to eight live data parameters simultaneously and includes ECU information and diagnostic topology mapping.

Equipped with a 2.2GHz+1.8GHz Octa-core processor, 8GB RAM, 128GB storage, and a 10.1-inch touchscreen, the IP919 offers swift operation and seamless multitasking. It features a collapsible kickstand, built-in speaker and microphone, a rear camera, and a 6400mAh 7.2V battery for extended use.

The IP919 supports full system diagnostics, full OBD II functions, activation tests, coding, vehicle-specific functions, FCA AutoAuth, ADAS calibration, ECU configurations, VAG guided functions, PMI, and 51 special functions.

1.1 Diagnostic Topology Mapping Advantages

  • Systematic Troubleshooting: Provides a clear overview of ECU interrelationships.
  • Enhanced Accuracy: Helps identify root causes of problems.
  • Increased Efficiency: Streamlines workflow.
  • Cost Savings: Reduces labor costs.
  • Integration with Advanced Diagnostic Tools: Enhances effectiveness when used with OBD systems.

2. Safety Information

For your safety, the safety of others, and to prevent damage to devices and vehicles, it is crucial to read and understand all safety instructions presented in this manual before operating or coming into contact with the device.

2.1 General Safety Instructions

  • Read and Understand: Ensure all operators and individuals in the vicinity of the device have read and understood these safety instructions.
  • Proper Use: Only use the device as described in this manual. Always adhere to safety messages and test procedures provided by the vehicle or equipment manufacturer.
  • Knowledge and Skill: Automotive technicians must be knowledgeable about the system being tested and familiar with proper service methods and test procedures.
  • Acceptable Testing Practices: Perform tests in a manner that ensures your safety, the safety of others, and prevents damage to the device and the vehicle.

2.2 Specific Responsibilities

  • Refer to Manufacturer Guidelines: Always consult and follow safety messages and applicable test procedures from the vehicle or equipment manufacturer.
  • Use Appropriate Tools and Techniques: Use correct tools and techniques for each specific task, considering the variety of test applications and product variations.
  • Anticipate Safety Requirements: Be prepared to handle unforeseen circumstances safely, as this manual cannot cover every potential situation.

2.3 Safety Messages

Safety messages are included to prevent personal injury and equipment damage. Each message begins with a signal word indicating the hazard level:

Danger

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury to the operator or to bystanders.

Warning

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury to the operator or to bystanders.

2.4 Safety Instructions for Operation

  • When the engine is running: Ensure the service area is well ventilated or connect a building exhaust removal system to the engine exhaust to prevent carbon monoxide poisoning.
  • Safe Environment: Always perform automotive testing in a safe environment.
  • Eye Protection: Wear safety eye protection that meets ANSI standards.
  • Avoid Hazards: Keep clothing, hair, hands, tools, and test equipment away from all moving or hot engine parts.
  • Ventilation: Operate the vehicle in a well-ventilated work area to avoid inhaling poisonous exhaust gases.
  • Transmission and Brakes: Put the transmission in PARK (for automatic) or NEUTRAL (for manual) and ensure the parking brake is engaged.
  • Wheel Blocks: Place blocks in front of the drive wheels and never leave the vehicle unattended while testing.
  • Ignition System Caution: Be extra cautious around the ignition coil, distributor cap, ignition wires, and spark plugs, as these components generate hazardous voltages.
  • Fire Extinguisher: Keep a fire extinguisher suitable for gasoline, chemical, and electrical fires nearby.
  • Test Equipment Connections: Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
  • Clean Equipment: Keep the test equipment dry, clean, and free from oil, water, or grease. Use a mild detergent on a clean cloth to clean the outside as necessary.
  • No Driving While Testing: Do not drive the vehicle and operate the test equipment simultaneously to avoid distractions.
  • Service Manual Reference: Refer to the service manual for the vehicle being serviced and adhere to all diagnostic procedures and precautions.
  • Battery Check: Ensure the vehicle battery is fully charged and the connection to the vehicle DLC is clean and secure.
  • Avoid Electromagnetic Interference: Do not place the test device on the vehicle's distributor, as strong electromagnetic interference can damage the device.

3. Setup

3.1 What's Included

The XTOOL InPlus IP919 package includes the following components:

XTOOL IP919 Package Contents
Image: XTOOL IP919 Package Contents, showing the tablet, VCI WiFi connector, various cables (Type C to A, Type C to B, Type C to C, Type C to PD-12V Charging Cable, DB15 Main Cable, Cigar Lighter Cable), adapters (US, EU, UK), and vehicle-specific connectors (KIA-20, Mazda-17R, Nissan-14, GM/Daewoo-12, Suzuki-3, Fiat-3, OBD II-16, Toyota-17, Audi-4, Mitsubishi-12+16, Universal-3, Citroen-2, BENZ-38, BENZ-14, HONDA-3, BMW-20, HYUNDAI/Kia-10).
Package Contents
ItemQuantity
IP919 Android Tablet1
VCI WiFi Connector1
Type-C to Type-A Data Cable1
Type-C to Type-B Data Cable1
Type-C to Type-C Charger Cable1
Type-C to PD-12V Charging Cable1
PD Supply Charging Adapter US1
Charger Adapter EU1
Charger Adapter UK1
Cigar Lighter Cable1
DB15 Main Cable1
OBDII-16 Connector1
HONDA-3 Connector1
BMW-20 Connector1
BENZ-14 Connector1
BENZ-38 Connector1
TOYOTA-17 Connector1
MAZDA-17R Connector1
KIA-20 Connector1
HYUNDAI/KIA-10 Connector1
NISSAN-14 Connector1
GM/DAEWOO-12 Connector1
UNIVERSAL-3 Connector1
SUZUKI-3 Connector1
FIAT-3 Connector1
CITROEN-2 Connector1
AUDI-4 Connector1
MITSUBISHI-12+16 Connector1
Wireless Charger Dock1
Color Carton1
Packing List1
Quick Start Guide1
Tool Case1

3.2 Physical Components

3.2.1 XTOOL IP919 Tablet

XTOOL IP919 Tablet and VCI Box
Image: Front view of the XTOOL IP919 tablet displaying a diagnostic screen with a topology map, alongside the VCI box.

The tablet features a 10.1-inch touch screen. Key ports and features include:

  • Type-C Port: For data transfer and charging.
  • Reset Hole: For device reset.
  • Power Button: To turn the device on/off.
  • Microphone: For audio input.
  • Charging Contact: For use with the charging dock.
  • Camera: Rear-facing 8MP camera.
  • Nameplate: Device identification.
  • Speaker: For audio output.

3.2.2 VCI Box

XTOOL IP919 VCI Box
Image: The XTOOL IP919 VCI Box, a wireless communication interface for vehicle diagnostics.

The VCI Box communicates wirelessly with the Diagnostic Tool via WiFi, offering faster transmission speeds, longer communication distances, and higher data capacity compared to Bluetooth. This enables more efficient and stable diagnostics.

Main ports of the VCI Box:

  • Screen: Displays status information.
  • DB15 Port: For main cable connection.
  • Nameplate: Device identification.
  • USB Type-B Port: For connection.
  • DC Port: For power input.

3.2.3 Charging Dock

The charging dock powers the tablet. Place the tablet on the dock to charge. The indicator light shows charging status: red for low battery, blue during charging, and green when fully charged.

3.3 Power Sources

The XTOOL IP919 Diagnostic Tool can receive power from three sources:

  • Internal Battery Pack: A rechargeable 7.2V 6400mAh Li-ion battery providing approximately 3.5 hours of continuous operation when fully charged.
  • AC Power Supply: Connect the AC power supply to a standard AC outlet and plug the output cable into the DC power supply input jack on the tablet or use the charging dock.
  • Charging Dock: Provides power and charges the internal battery.

3.4 Initial Setup

3.4.1 Turning On

Press and hold the power button on the top right of the device for approximately five seconds. The tool will automatically power on if the internal battery has sufficient charge or if connected to an AC power supply. If the battery is completely drained, charge it for more than 6 hours before attempting to turn it on.

3.4.2 Turning Off

Press and hold the power button for more than three seconds. The tool will automatically power off.

IMPORTANT:

Before turning off, terminate all vehicle communications. Forcing a shutdown during communication could cause issues with the ECM. Never disconnect the DBD-15 main cable while the Diagnostic Tool is actively communicating with the vehicle ECM.

3.4.3 Emergency Shutdown

If the Diagnostic Tool is unresponsive or exhibits erratic operation, press and hold the power button for five seconds until it turns off. This procedure should only be used in emergencies.

IMPORTANT:

Using emergency shutdown while communicating with the vehicle ECM may lead to ECM problems on some vehicles.

3.5 Language Settings

XTOOL IP919 Language Settings
Image: Steps to set the language on the XTOOL IP919, showing activation, switching language in settings, and updating the app.

To change the language of the Android tablet, go to 'Settings' > 'Language'. The IP919 supports 22 languages including English, Arabic, French, Polish, Portuguese, Russian, Danish, German, Greek, Spanish, Finnish, Hungarian, Italian, Japanese, Korean, Dutch, Norwegian, Swedish, Thai, Turkish, Vietnamese, and Traditional Chinese. After changing the language, re-download the model software in the corresponding language. Update the APP to the latest version via 'Diagnosis APP' > 'Setting' > 'APP'.

3.6 Wi-Fi Connection

The Diagnostic Tool can connect to 2.4 GHz or 5.0 GHz Wi-Fi networks. Swipe up the hidden bottom toolbar, click Home > Network & Internet > Switch on Wi-Fi connection > Click Wi-Fi icon to view available networks > Select your network and input the password.

If home Wi-Fi is unavailable or not functioning well, you can connect to a mobile phone hotspot:

  • For iOS users: Go to Settings > Turn on cellular network > Personal Hotspot > Switch on 'Allow Others to Join' and 'Maximize Compatibility'.
  • For Android users: Go to Settings > Wireless & networks > Tethering & portable hotspot > Portable WLAN hotspot > Switch on hotspot > Configure WLAN hotspot > Encryption Type > WPA2 PSK. Ensure 'Max connections allowed' has user left for the Diagnostic Tool.

NOTE:

Wi-Fi connection is not necessary for diagnostics with most vehicle brands. However, for certain brands like Peugeot, which require access to an online server during diagnostics, it is essential to connect to Wi-Fi.

3.7 Product Activation

Follow these steps to activate your device:

  1. Select a language for the operating system.
  2. Connect to an available Wi-Fi network. (You can use the 'TRAIL' button to try it out before activation, but activation is recommended for online software updates.)
  3. Click 'Register' to enter the activation page.
  4. Fill in your email and create a password.
  5. A pop-up window showing 'Login successful' indicates the first boot setup is complete.
  6. Click 'Start now' to enter the diagnostic system.

Once 'Login successful' is displayed, the Diagnostic Tool is registered and activated. The device will remember your account information for future logins.

NOTE:

If you cannot register or see the activation screen, contact support@xtoolonline.com.

3.8 Vehicle Connection

XTOOL IP919 Vehicle Connection Diagram
Image: Diagram illustrating the connection of the XTOOL IP919 tablet and VCI box to a vehicle's OBD-II port.

To connect the Diagnostic Tool to a vehicle:

  1. Press and hold the Power button to turn on the tablet.
  2. Select the App language and start the activation process.
  3. Follow the on-screen hints to complete the activation.
  4. Connect the DB15 connector of the main cable to the VCI box.
  5. Plug the OBDII-16 connector of the main cable into the vehicle's DLC port.
  6. When the VCI box powers on, the tablet will automatically search for it and establish a WiFi connection.
  7. Your tablet is now ready for diagnostics.

NOTE:

For models using DOIP (Diagnostic Over Internet Protocol), ensure a wired connection to the vehicle for reliable communication.

4. Operating Instructions

4.1 Diagnostic Screen Layout

XTOOL IP919 Diagnostic Screen Layout
Image: The XTOOL IP919 diagnostic screen showing main functions: Diagnostic, Special Function, Report, Updates, More, Remote Control, Settings, XTOOL, and Auto Scan.

When the Diagnostic Tool is turned on, the diagnostic program starts automatically, displaying the diagnostic screen. A hidden toolbar at the bottom of the tablet can be revealed by swiping up from the bottom of the screen for 3 seconds.

4.1.1 Diagnostic Screen Icons

  • Auto Scan: Automatically detects and decodes the VIN, then comprehensively scans all available vehicle electronic control modules for diagnostics.
  • Diagnostic: Accesses the diagnostic menu, allowing Auto VIN detection, manual vehicle information input (make, model, year, configurations), DEMO program access, and OBD-II tests.
  • Special Function: Covers commonly performed maintenance services for DIYers and professionals.
  • Report: Includes functions for diagnostic reports, data playback, and data viewing.
  • Updates: Allows downloading diagnostic software programs individually or in batch.
  • More: Provides access to user account setup, workshop profile, subscription period, firmware information, endoscope feature, and user manual in PDF format.
  • Settings: Customizes language, units, USB mode, OS settings, volume, brightness, and displays device information (App version, OS version, Serial Number, VCI number).
  • Remote Control: Launches TeamViewer for remote assistance.
  • XTOOL: Provides contact information for support.

4.2 Main Screen Layout

Swiping up from the bottom of the touchscreen reveals a hidden toolbar. The home button on this toolbar brings up the main Android tablet screen, allowing switching between horizontal and vertical views. Icons on the main screen include:

  • Calendar: Displays calendar in day, week, and month views.
  • Contacts: Manages contact information; add new contacts or import from VCF files.
  • Clock: Sets alarms, timers, stopwatch, and accesses the clock.
  • Email: Creates new email accounts for sending emails or sharing reports.
  • Music: Adds songs, playlists, albums, artists.
  • Sound Recorder: Records voice messages.
  • Calculator: Opens the calculator.
  • Files: Manages documents, reports, files, and folders.
  • Adobe Acrobat: Manages PDF files and accesses Dropbox accounts.
  • Quick Support: Enables remote control by tech support for troubleshooting.
  • Gallery: Views screenshots and screen recordings.
  • Camera: Activates the rear camera to take pictures.
  • Endoscope: Used with an endoscope for visual inspection in narrow areas.
  • Browser: Accesses the XTOOL website and searches for information.

4.3 Data Transfer

4.3.1 Connect to USB Type-C Port for Data Transfer

  1. Connect the Diagnostic Tool to a PC using a Type-C cable.
  2. Swipe down from the upper right or upper left corner of the Diagnostic Tool to bring up the drop-down menu. Click on 'Android System. USB file transfer turned on'.
  3. Change the option from 'No data transfer' to 'File Transfer'.
  4. On the PC, click on 'IP919' to access and manage files in the internal memory.

4.3.2 Share CSV File via Bluetooth

To share a CSV file to an Android tablet or phone:

  1. Swipe up the hidden toolbar and click the home icon to go to the main Android tablet screen.
  2. Click 'File' > 'Local' > 'Home' > 'Diagnosis' > 'CSV_records'.
  3. Press and hold the CSV file to activate the selection box, tick the box.
  4. Click 'More' at the bottom left > 'Share' > 'Bluetooth' > Select the device to share with.

NOTE:

Files cannot be shared to iOS devices from an Android tablet.

4.4 Color Correction Mode

To set the Diagnostic Tool to red-green color blindness correction mode:

  1. Swipe up from the bottom of the screen to bring up the hidden menu.
  2. Click the home button to switch to the main screen of the Android tablet.
  3. Navigate to Settings > Accessibility.
  4. Scroll down to 'Color correction' and toggle 'Use color correction' to the on position.

4.5 Diagnosing Vehicles

To ensure proper communication and diagnostics, the vehicle must be correctly identified. The vehicle identification sequence is menu-driven.

4.5.1 Vehicle Identification

Follow these steps to establish communication:

  1. Follow Screen Prompts: Use menu-driven prompts to enter necessary vehicle information.
  2. Options for Vehicle Identification:
    • VIN (Vehicle Identification Number)
    • Manufacture area > Model > Year
    • Other specific criteria as required by the Diagnostic Tool

4.5.2 Auto Scan

Click 'Auto Scan' on the diagnostic screen. The tool will scan and decode the VIN for automatic vehicle identification.

IMPORTANT:

If Auto Scan fails, try 'Manual Selection' to input vehicle make, model, and year manually. Auto Scan may not be compatible with all vehicles.

4.5.3 Diagnostic Menu

Click the 'Diagnostic' icon to bring up the vehicle selection menu. Here you can find 'Auto Scan' and 'Manual Input' options. 'Manual Input' allows you to enter the 17-digit VIN manually.

NOTE:

If Auto Scan and Manual Input fail, try 'Automatic Detection' or 'Manual Selection'.

4.5.4 Automatic Detection

Click 'Diagnostic' > Select region > Select vehicle brand > Select 'Automatic Detection' to automatically detect and identify the vehicle.

NOTE:

Automatic Detection may not function with all vehicle models. If unsuccessful, choose 'Manual Selection'.

4.5.5 Manual Selection

If other methods fail, 'Manual Selection' is the most reliable option. Click 'Diagnostic' > Select region > Select vehicle brand > Select 'Manual Selection' > Select model year > Model Name, and follow further selections to reach 'Automatic Scan' and 'System Selection'.

4.5.6 CAN Fast Scan

For vehicles using the CAN protocol post-2005, scanning all available vehicle systems is much faster.

4.5.7 System Selection

After identifying potential problem areas, select an individual vehicle module for targeted diagnostics.

4.5.8 Diagnostics Overview

Once the vehicle is identified, the Diagnostic Tool can access electronic control systems to retrieve DTCs, PID data, freeze frame, ECU information, and perform actuation tests, resets, relearns, matchings, adaptations, and initializations.

4.6 OBD-II Functions

XTOOL IP919 ECU Programming and Coding
Image: XTOOL IP919 screen showing ECU Programming and Coding options, including replacing blank modules, repairing ECUs, upgrading software, and reprogramming operations. Also shows ECU Coding features like parameter adjustment, advanced customization, activating hidden functions, and performance enhancement.

This section covers OBD-II concepts, protocols, and test functions. To access, go to Diagnostic > Region Selection > OBD-II.

OBD-II functions allow checking for emissions-related DTCs, identifying the cause of a Malfunction Indicator Lamp (MIL), and checking monitor status before emissions testing.

IMPORTANT:

Generic OBD-II/EOBD data are not included in the engine system diagnostic data.

4.6.1 OBD-II Protocols

The tool supports 5 global OBD communication protocols:

  • J1850PWM
  • J1850VPW
  • ISO 9141-2
  • ISO 14230-4
  • ISO 15765-4 (CAN)

4.6.2 Basic Operations

To access generic OBD-II/EOBD data:

  1. Click 'Diagnostic' on the main diagnostic screen.
  2. Select the region where the vehicle manufacturer originated.
  3. Click the 'OBD-II' icon beside the DEMO.

4.6.3 10 Modes of OBD-II

  • Mode $01 – I/M Readiness
  • Mode $02 – Read Freeze Frame
  • Mode $03 – Read Trouble Code
  • Mode $04 – Clear Trouble Code
  • Mode $05 – O₂S Monitoring Test
  • Mode $06 – On-Board Monitor Test
  • Mode $07 – Read Trouble Code
  • Mode $08 – Component Test
  • Mode $09 – Vehicle Information
  • Mode $0A – Read Trouble Code

4.6.4 Read Trouble Code

Displays current emission-related DTCs, including Stored Codes (Generic and Manufacturer-Specific), Pending Codes, and Permanent Codes.

DTC Structure:

A typical OBD-II code (e.g., P0782) indicates:

  • First Character: Letter (P=Powertrain, C=Chassis, B=Body, U=Network Communication).
  • Second Character: Numeric digit (0=Standard SAE, 1=Manufacturer-Specific).
  • Third Character: Subsystem (0=Fuel/Air Metering/Auxiliary Emissions, 1=Fuel/Air Metering Injection, 2=Fuel/Air Metering (Injection), 3=Ignition/Misfires, 4=Auxiliary Emissions, 5=Vehicle Speed/Idle Control/Auxiliary Inputs, 6=Computer Output Circuit, 7-8=Transmission).
  • Fourth and Fifth Characters: Two-digit numbers (0-99) identifying the specific malfunction.

4.6.5 Clear Trouble Code (Mode $04)

Erases all emission-related diagnostic data, including DTCs, freeze frame data, and test results, from the ECM. A confirmation screen appears to prevent accidental data loss.

4.6.6 Live Data (Mode $01)

Views current emission-related data from the ECM. Displays parameter descriptions and corresponding values with units or states.

4.6.7 Read Freeze Frame (Mode $02)

Displays a snapshot of critical parameter values at the moment a DTC is set. This data typically corresponds to the last DTC that occurred, but for emissions-critical DTCs, the highest priority DTC's freeze frame is retained.

4.6.8 I/M Readiness (Smog Check)

Checks the readiness of the monitoring system. Useful before emissions certification testing. Offers two choices: 'Monitor status since DTCs cleared' and 'Monitor status this driving cycle'.

4.6.9 O₂S Monitoring Test (Mode $05)

Opens a menu of tests to check the integrity of oxygen sensors (O₂S). Displays pertinent O₂S parameters for the selected test.

4.6.10 On-Board Monitor Test (Mode $06)

Views results of On-Board Monitor (OBM) tests, useful after vehicle servicing or ECM memory erasure. Displays test results for monitored systems.

4.6.11 Component Test (Mode $08)

Enables bidirectional control of the ECM to test components like EVAP leakage. Useful for determining if the ECM responds to commands.

4.6.12 Read Vehicle Information (Mode $09)

Requests and displays vehicle-specific information such as VIN, calibration identification, and calibration verification number (CVN).

IMPORTANT:

Not all vehicles support all service modes; available menu selections will vary.

4.7 Special Functions

XTOOL IP919 51+ Reset Functions
Image: Grid of icons representing 51+ reset functions including ABS Bleeding, EPB Reset, SAS Reset, Oil Reset, BMS Reset, Injector Coding, Throttle Reset, D-P-F Regeneration, Gearbox Match, Suspension, SRS Reset, Seat Calibration, Headlight, Stop/Start Reset, Airbag Reset, A/C Relearn, TPMS Reset, Coolant Bleeding, Power Balance, Crank Sensor Relearn, Adblue Reset, Write VIN, Tire Size Reset, Clutch Adaption, Control Unit Reset, ADAS, and more.

The IP919 offers 51+ hot services, including:

  • Oil Reset: Resets the engine oil life system after an oil change.
  • EPB Reset: Resets the electronic parking brake system after brake pad replacement.
  • EPS Adaptation: Calibrates the steering angle sensor (SAS) after replacement or repair.
  • BMS Reset: Resets the Battery Management System after battery replacement.
  • Injector Adaptation: Writes the identification code of new fuel injectors into the ECU.
  • DPF Regen: Manages Diesel Particulate Filter regeneration.
  • GPF Regen: Manages Gasoline Particulate Filter regeneration.
  • TPMS Reset: Performs learning, matching, and resetting functions for tire pressure sensors.
  • ABS Bleeding: Bleeds the brake system to restore ABS brake sensitivity.
  • Power Balance: Shuts down individual injectors to determine cylinder malfunctions.
  • Seat Calibration: Matches or configures seats with memory function.
  • EEPROM: Reads and writes data into EEPROM (requires adapter).
  • Language Change: Changes the system language of the instrument cluster.
  • Transport Mode: Deactivates or disables transport mode for vehicles.
  • Control Unit Reset: Resets ECU software after faults.
  • Throttle Adaptation: Resets throttle actuators and learned values to default.
  • Rain/Light Sensor: Resets the sensor after replacement.
  • AFR Adaptation: Resets or relearns air/fuel ratio parameters.
  • HV Battery: Checks individual battery pack voltage.
  • Gearbox Adaptation: Completes self-learning of the gearbox.
  • Speed Limit: Removes speed limits for imported vehicles.
  • CPS Reset: Performs tooth learning for the vehicle.
  • Clutch Adaption: Resets the clutch after replacement.
  • Stop/Start Reset: Opens or closes the automatic Start/Stop function.
  • FRM Reset: Resets the Footwell Room Module.
  • EGR Relearn: Learns the EGR valve after cleaning or replacement.
  • A/C Relearn: Performs AC system relearn.
  • Headlight: Initializes the adaptive headlight system.
  • ABS/ESP Adaptation: Resets the acceleration sensor.
  • Windows Initialization: Recovers ECU initial memory for power windows.
  • Sunroof Initialization: Recovers ECU initial memory for sunroof.
  • Turbo Relearn: Calibrates newly installed turbo components.
  • Water Pump Actuation: Activates the electric water pump.
  • Suspension Adaptation: Adjusts vehicle body height sensor.
  • Airbag Reset: Resets the airbag system and clears crash data.
  • Tire Size Reset: Resets tire size after replacement or upgrade.
  • Instrument Cluster: Adjusts mileage displayed.
  • ECU Configurations: Queries and activates hidden functions.
  • ADAS: Recalibrates the ADAS system after module/sensor replacement.
  • Adblue Reset: Lifts vehicle restrictions due to insufficient diesel urea.
  • Nox Reset: Resets the system after oxygen sensor/catalyst replacement.
  • Write VIN: Writes VIN to ECUs after replacement.
  • Odometer Read: Queries vehicle mileage information.
  • IMMO Reset: Resets or reprograms the Immobilizer System for key matching.
  • Coolant System Functions: Drains and refills coolant.
  • EVAP Test: Tests fuel evaporative emissions control systems for leaks.
  • Cam Sensor Adaptation: Calibrates engine control unit to camshaft position.
  • Glow Plug Reset: Restores glow plug system to initial state.
  • TCM Service Reset: Resets transmission fluid counter or maintenance reminder.
  • Fuel Pump Priming: Ensures normal operation of the fuel pump.

4.8 ECU Coding & Programming

XTOOL IP919 ECU Online Coding & Offline Coding
Image: XTOOL IP919 screen showing ECU Online Coding & Offline Coding features, including module replacement matching, personalized settings (unlocking features like DRLs, power-folding mirrors), and fault repair (ECU initialization and re-matching).

The IP919 offers online and offline ECU coding for component matching, ECU replacement, retrofit & modification. It helps bypass gateways to access data for coding (e.g., VW, Audi, Skoda, Benz, BMW, Mitsubishi). It supports reflashing modules, reprogramming second-hand or blank ECUs, and flashing hidden functions for vehicle personalization. This is a solution for ECU tuning needs, allowing programming or flashing ECUs after module replacement. Currently available for BMW, Audi, Skoda, and Benz.

NOTE:

After replacing control units, actuators, or parts, coding is necessary for the ECU to recognize them. Read and record original module information before coding.

4.8.1 Flash Hidden Functions (ECU Configurations)

Customize functions to change or add features unique to high-end vehicles, such as disabling seat belt alarms or turning off daytime running lights.

4.8.2 PMI (Programmable Machine Interface) Functions

When replacing or initializing, the PMI function allows copying data from the original module to a new unit for module replacement (for Ford, Lincoln, Mazda). This function is displayed only for these specific models.

4.9 VAG Guided Function & BMW Test Plan

XTOOL IP919 VAG & BMW Guided Function
Image: XTOOL IP919 screen showing VAG & BMW Guided Function steps (Start, Step 1, Step 2, OK!) for engine control unit identification, along with FCA Vehicle Access login screen and 8-in-1 real-time data graph.

The IP919 provides step-by-step repair guidance to prevent damage from incorrect operations. It offers diagnostic steps based on vehicle fault DTCs, including module testing, functional testing, wiring diagrams, and component location maps. This simplifies troubleshooting for beginners and DIYers. Specifically designed for BMW, VW, Audi, Skoda, Seat, Bentley, and Man LD cars.

4.10 FCA AutoAuth

For 2018 and later FCA vehicles with a Secure Gateway Module, register with AutoAuth to enable the IP919 to communicate with the FCA Authentication System. This bypasses the need for a bypass cable to perform diagnostics and bi-directional controls on Dodge, Jeep, Chrysler, etc. Some vehicles may require unlocking the gateway for other special functions.

4.11 Built-in CAN FD & DoIP New Protocol

The IP919 supports CAN FD Protocol for GM and Chevrolet cars 2020 and newer, eliminating the need for an extra adapter. It works with newer vehicles like Chevrolet Onix, Tracker, Suburban, Buick, Cadillac Escalade, GMC Yukon, Daewoo, Alpheon, Pontiac, Hummer. It also supports DoIP for BMW E/F/G Chassis, Jaguar, Land Rover, Volvo, etc.

4.12 All Cars Lifetime Free Use Full System Diagnostic

The IP919 scans all available electronic systems of cars to troubleshoot issues. The Diagnostics application links to the vehicle's electronic control system for reading/clearing codes, viewing ECU info, live data, active tests, and special functions for all systems (Drive, Chassis, Body, Electrical). The number of systems scanned depends on the vehicle's configuration.

4.13 Topology Map

XTOOL IP919 Topology Map Diagnostic
Image: XTOOL IP919 screen showing a Topology Map Diagnostic with full systems scan, displaying interconnected modules like Engine, SRS, TPMS, Chassis, BMS, EPB. Also shows examples of bi-directional tests for Window, Wiper, Headlight, Mirror, Radiator Fan, Compression, Injector Buzz, and Sunroof.

The IP919 displays vehicle modules with a color-coded topology communication structure network, showing current module status. This Smart Topology Module Mapping allows direct viewing of communication structures, clicking to check fault codes, and accessing systems, making it easy to identify and locate faults in the vehicle's electrical system.

4.14 Bi-Directional Control & Actuation Test

XTOOL IP919 Bi-Directional Controls
Image: XTOOL IP919 screen demonstrating Bi-Directional Controls with an 'Actuation Test' interface, showing commands being sent and received to various vehicle components like window, air conditioner, headlights, mirror, wiper, sunroof. It highlights troubleshooting capabilities for pinpointing faulty components.

With 4000+ actuation tests, the IP919 can command components (e.g., doors, windows, ABS pump, A/C clutch, cooling fan, fuel pump, injectors, EVAP purge solenoid, wipers, horns, roof) to switch on/off. This helps quickly determine if an issue is with wiring, a relay, or the component itself, saving troubleshooting time. Examples include Fuel Injector Balance, Fuel Pump Enable, EVAP Tests, ACC Lane Keeping Assist System control, and Oil Pressure Control Test.

NOTE:

Compatibility varies by VIN; not universal for all vehicles.

4.15 Key Programming Function (IMMO Reset)

XTOOL IP919 Key Programming Capability
Image: XTOOL IP919 screen showing Key Programming capabilities, including Add New Keys, All Keys Lost, Remote Relearn, and IMMO Reset. A note indicates that key programming is not supported for all vehicles and to check compatibility.

The IMMO Reset function can disable lost vehicle keys and program replacement key fobs. It supports programming new key fobs, reading PIN codes, checking the number of keys, generating keys, adding keys, and handling all keys lost scenarios. This function ensures the immobilizer control system identifies and authorizes remote control keys.

NOTE:

Not all cars support key programming. Check compatibility with the seller before purchase.

4.16 Pre & Post Scan Reporting

XTOOL IP919 Pre & Post Scan Report
Image: XTOOL IP919 screen showing a 'Pre-Scan Report' and 'Post-Scan Report' interface, demonstrating how to conduct a comprehensive pre-scan to identify issues and a post-scan to confirm repairs and validate vehicle performance.

The IP919 offers Pre & Post Scan functions. A pre-scan identifies potential issues before repairs, detecting DTCs and system faults. A post-scan confirms repairs are resolved, clears DTCs, and validates vehicle performance. This provides clear comparisons of vehicle conditions before and after repairs, helping avoid unnecessary fees and ensuring safe driving.

4.17 Live Data Visualization & Export (8-in-1)

XTOOL IP919 Live Data Visualization & Export
Image: XTOOL IP919 screen showing Live Data Visualization & Export, with a graph displaying up to 8 live data PIDs simultaneously. Options for Data Record & View, Export Data as CSV File, and Data Playback are highlighted.

The IP919 provides powerful data graphing capabilities, showing up to 8 individual graphs merged on one screen for comparison. You can customize specific PIDs and merge graphs for up to 8 data PIDs. Data streams can be exported as CSV files for storage and comparison over time. Diagnostic reports can be generated, printed, or shared.

4.17.1 PID Data List

Click the live data function to display a list of PID names and real-time values. You can choose from four viewing modes: List, Column, Graph, and 2D-Graph.

4.17.2 Individual PID Data Graphing

Click the 'custom' icon to view graphing for individual PID data and select the desired format.

4.17.3 Set Maximum & Minimum Value Alarms

Click the alarm icon to set maximum and minimum value alarms for individual PID data. The diagnostic tool will display colors to indicate if PID data exceeds or falls below these values.

4.17.4 Zoom In & Zoom Out & View In Full Screen

Click the magnifier icon to zoom in on the x-axis (up to 3 times) and the magnifier icon to zoom in on the y-axis (up to 3 times). Clicking again returns to original size (X1).

4.17.5 Custom Up to 8 PID Data

Tick boxes for up to 8 PID data points and click 'Custom' to display a custom list of real-time PID data. 'Cancel Selected' allows re-selection, and 'Custom' proceeds to display the custom screen.

4.17.6 Data Recording & Playback

Click 'Record' to start recording PID data for later review via the 'Report' function. Click 'Pause' to pause the retrieving process.

4.17.7 Export Data as CSV & Data View

When recording, the 'save' button blinks. Click it again to save the recorded data stream. After collecting data, click the back icon to rename the CSV file. 'PREVIEW' allows reviewing the generated CSV file. To view exported CSV files, go to Main Diagnostic Screen > Report > Data View.

4.18 Health Report Generate and Share

Generate a full system Diagnostic Report with one click. Reports can be emailed or printed. Customize your name, address, and other information on the report. Upgraded v2.0 Diagnostic Report features include selecting content, revising names, adding logos/customer info/attachments, saving/sharing via email, and highlighting critical systems for readability.

4.19 AI-Assisted Diagnostics

XTOOL IP919 AI-Assisted Diagnostics
Image: XTOOL IP919 screen showing AI-Assisted Diagnostics features, including analyzing fault codes, analyzing diagnostic reports, and maintenance service guidance for DIYers, mechanics, and beginners.

The newly added AI reply function provides fast and accurate answers to inquiries, supports multiple languages, and generates repair suggestions for car repair shops. It helps free users from inefficient and repetitive work, focusing on high-value customers and differentiated services. Functions include analyzing fault codes, diagnostic reports, and maintenance service guidance.

5. Maintenance

5.1 Software Updates

XTOOL IP919 3 Years Update Via WiFi
Image: XTOOL IP919 screen showing a device with an arrow pointing upwards, indicating '3-Years Update Via WiFi'. Text highlights improved device performance through enhanced compatibility, better user experience, and software improvements.

The IP919 comes with 3 years of free software updates, offering new features, bug corrections, and wider vehicle coverage. Updates can be performed via Wi-Fi or a mobile hotspot. If a 'Network abnormal' prompt appears, try another Wi-Fi network or contact support.

Two update options:

  1. Update All Software Programs: Click 'Update All' at the bottom right of the update menu.
  2. Update Individual Software Program: Click the arrow icon next to the specific program. If interrupted, click the icon again.

5.1.1 Delete Software Program

To free up memory, delete rarely used software programs by going to 'Diagnostic' > Select Region > Press and hold the vehicle maker icon for 5 seconds > Click 'Delete'.

IMPORTANT:

Do not delete software programs close to the subscription expiration date. Re-download deleted programs before expiration to ensure access.

5.2 Storage Management

You can clear the cache and check remaining memory by navigating to Settings > Storage Management.

5.3 Cleaning Equipment

Keep the test equipment dry, clean, and free from oil, water, or grease. Use a mild detergent on a clean cloth to clean the outside of the equipment as necessary.

6. Troubleshooting

6.1 FAQs

Here are answers to common questions:

Q1. I haven't found I/M readiness in the menu.
A: Enter Diagnostic > Select America/Europe/Asia > Click the 'OBD-II' icon > Auto Scan/Select OBD-II Protocol > I/M Readiness.
Q2. Unable to find live sensor data as the generic OBD2 scanner, like short-term/long-term fuel trim.
A: Enter Diagnostic > Select America/Europe/Asia > Click the 'OBD-II' icon > Auto Scan/Select OBD-II Protocol > Live Data > LTFT, STFT or similar term.
Q3. Unable to find the misfire data for my Ford/Dodge/Chrysler/Jeep cars?
A: Select Diagnostic > America/Europe/Asia > OBD-II > Auto Scan or Select OBD-II Protocol > On Board Monitor Test > Select 'Misfire Cylinder Data' or similar term.
Q4. How to export live data as CSV files?
A: To generate CSV files: Live data > custom > Choose live data > Record > Save > Preview. To find CSV files: Report > CSV View > Choose the saved live data.
Q5. I cannot charge the battery now. I plugged in the cord, it's not charging. The battery is almost dead, only about 10% left.
A: 1. Try using the original charging cable or OBD test cable to charge for more than six hours (preferably with a stable 12V power supply). 2. Hold down the shutdown button for 15 seconds and observe if the device turns on normally (without charging cable). 3. Connect to a computer via USB to see if it's recognized. 4. If issues persist, contact support@xtoolonline.com with a video of the charging issue.
Q6. Can scanner tune up car?
A: No, the IP919 Diagnostic Tool does not have the capability to tune up cars.
Q7. Can this scanner still be used once the 3 year free updates are finished?
A: Yes, you can still use its last updated software. New updates require renewal.
Q8. It was frozen until the battery went flat even I tried the reset button and the power button.
A: Ensure the App is updated (Settings > About > App). If updated, reset to factory settings. If the problem persists, contact support@xtoolonline.com.
Q9. I cannot update, I've tried Wi-Fi and cell phone as hotspot, however, keep telling me failure connection.
A: This could be due to router firewall settings or network provider restrictions. Check if your router firewall allows access to the server. If the problem persists, contact support@xtoolonline.com.
Q10. Any chance to install Google Play store?
A: No, the diagnostic tool does not support Google Play store. Third-party apps can be installed via APK files, but it's not recommended as it may slow down performance.
Q11. Why should I connect the scanner to internet once a month?
A: This is a government policy compliant requirement to report IP location and prevent illegal activities.
Q12. The auto scan/VIN cannot work on my vehicle.
A: Auto scan/VIN may not work for all vehicles due to VIN not being stored in ECU, database limitations, or specific vehicle communication modes. Try alternative navigation methods: turn on ignition (and engine for older vehicles) for auto scan, manual VIN input, or automatic/manual detection via Diagnostic menu.
Q13. My diagnostic tool cannot connect to Wi-Fi.
A: If it shows 'times out', check router settings (WPA2, not WPA3) and ensure no outgoing network traffic is blocked. Mobile hotspot often resolves registration issues. If connected but shows 'connect internet to sync your device', correct the Android system's time zone to match the network time zone.
Q14. How can I change the menu language into Spanish?
A: Send the device's S/N to support@xtoolonline.com for Spanish software program authorization. After authorization, change the Android tablet language to Spanish in 'Settings' > 'Language', then download all software programs under 'Updates'.
Q15. Why the scanner shows the report shared successfully but the email box didn't receive the report?
A: Reports sent from service@xtoolonline.com may be blocked by email providers. Whitelist the email address. Check junk mail. Contact support@xtoolonline.com if issues persist.
Q16. When you enter the diagnosis software program, it shows 'license exception' or 'Failed' error message.
A: Delete and re-download the software programs under 'Updates'. If the issue persists, contact support@xtoolonline.com with the device's S/N.
Q17. Browser can access internet normally, but can not download the updates under 'Updates', prompted to check the network connection in the Update.
A: Switch to a mobile hotspot or another Wi-Fi network and try again.
Q18. When activating the device, shows error message 'registration failure' after entering your email address.
A: Try a mobile hotspot (recommended) or a different network to activate.
Q19. Received a used device with a lock screen password, unable to open the device.
A: Contact support@xtoolonline.com with the device's S/N to resolve the issue.
Q20. How to use the function of 'Remote Control'?
A: The 'Remote Control' menu is for tech support. Schedule an appointment with XTOOL engineers, as remote control cannot be initiated without one.
Q21. What is the update fee of IP919? After my IP919 pass the free subscription date, can I use it as usual as before?
A: The renewal fee is $99 per year after the 3-year free update period. You can still use the last updated software, but new updates require renewal. You can extend for 1-year periods.
Q22. How can I subscribe the update on my IP919?
A: Transfer payment to info@acartool.com via PayPal, then provide a screenshot of the transaction to support@xtoolonline.com. Updates will be added within 24 hours.
Q23. I don't want to register an account. Why I failed to perform the functions at the trial mode?
A: Trial mode is for practice and familiarization; functions are limited without registration. Register an account for full functionality. If issues persist after registration, contact support@xtoolonline.com with S/N, VIN, and failed functions.
Q24. When using the trial mode, do I need to connect my device to the Internet/Wi-Fi?
A: No, internet connection is not needed in trial mode.
Q25. Shall I connect my device to the Internet/Wi-Fi all the time?
A: No, only for initial registration and downloading updates. Some advanced features like ECU Programming or specific vehicle brands (e.g., Peugeot) may require an internet connection.
Q26. Does your tools can support all the functions on all vehicles?
A: No, like other scan tools, it cannot perform all functions on all vehicles due to varying vehicle configurations and manufacturer limitations.
Q27. Why I manually enter the VIN on my device, the letters of Q, I, O on the keyboard are gray?
A: VIN standards (ISO, SAE, Chinese national) prohibit Q, I, O to avoid confusion with 1 and 0. This is normal.
Q28. How can I transfer the device's data to my phone or PC?
A: For Android phones, agree to receive transfer via Bluetooth. For PC: 1. Connect via Type-C cable. 2. Swipe down, click 'Android System. Charging this device via USB'. 3. Change to 'File Transfer'. 4. On PC, click 'IP919' to access files. iOS phones are not supported for direct file transfer.

6.2 Submitting Feedback

Click the message icon in the top right corner of the Automatic Scan screen to submit feedback to the support team regarding app or software issues.

6.3 Remote Control

The 'Remote Control' function allows XTOOL technical team to remotely assist with tasks. Ensure the tool is connected to Wi-Fi and TeamViewer is 'ready to connect'. Note the TeamViewer ID and schedule an appointment.

6.4 Data Logging

For software-related issues, data logging provides crucial information. Keep the Diagnostic Tool connected to Wi-Fi for at least 15 minutes and provide the Serial Number (e.g., IP919-00000) to support for analysis.

6.5 App Logging

For app-related issues, request an app logging collection tool from technical support. This tool gathers detailed information about app performance and specific issues.

6.6 FAQ Database & Training Videos

Access the FAQ database and product training videos on the XTOOL website: https://www.xtoolonline.com/faqs and https://www.xtoolonline.com/support/product-videos.

7. Specifications

XTOOL IP919 Next-Level Hardware
Image: XTOOL IP919 highlighting 'Next-Level Hardware' with features like an 8-Core Processor, Android 10.0, 8GB+128GB memory, Extra Charge Docking Station, 6400mAh battery (16+ hours work), Wireless Connect, 10.1-inch display, and 8MP Rear camera.
Technical Specifications
ItemDescription/Specification
Display10.1 Inch Touch Screen, 1920 x 1200 Resolution
Operating SystemAndroid 10.0
Processor2.2GHz+1.8GHz Octa-core Processor
Memory8G RAM, 128G ROM
ConnectivityBluetooth 5.0, Wi-Fi (2.4GHz & 5Ghz), Type-C
Operating MethodFlat Panel Touchscreen
Upgrade MethodDevice Connects to WIFI for Online Upgrade
Battery7.2V Rechargeable Li-ion Battery, 6400mAh
Tested Battery Life3.5 Hours
Power Supply Input100-240V~50-60Hz 0.5V Max
Power Supply Output5.0V-3.0A 15.0W/9.0V-2.22A 19.98W/12.0V-1.67A 20.04W
Dimensions (L×W×H)31.5*3.2*19(CM)
Free Renewal Update3 Years
Charging MethodType-C Charging (Fast Charging), Charge Dock
Supported ProtocolsCAN FD/DOIP/FCA
USB PortUSB2.0
WIFI2.4G/5Ghz
SensorGravity Accelerometer/Ambient Light Sensor
AudioMicrophone
SpeakerBuilt-In Speaker
Camera8 Mega Pixel
Weight (Including Battery)1.41 KG
Gross Weight8.3 KG
Operating Temp Range (Ambient)32°F ~ 104°F (0°C ~ 40°C)
Storage Temp (Ambient)14°F ~ 122°F (-10°C ~ 50°C)
Operating Humidity<90%

8. Warranty & Support

8.1 Limited Two-Year Warranty

Shenzhen XTOOLONLINE tech Intelligent Co., LTD. (the Company) warrants to the original retail purchaser that this XTOOL device, or any part thereof, proven defective in material or workmanship under normal usage and conditions within two years from the date of purchase, will be repaired or replaced (with new or rebuilt parts) with proof of purchase, at the Company's option, without charge for parts or labor directly related to the defect(s).

The Company is not liable for incidental or consequential damages arising from the use, misuse, or mounting of the device.

8.1.1 Warranty Exclusions

This warranty does not apply to:

  1. Products subjected to abnormal use or conditions, accident, mishandling, neglect, unauthorized alteration, misuse, improper installation/repair, or improper storage.
  2. Products whose mechanical or electronic serial number has been removed, altered, or defaced.
  3. Damage from exposure to excessive temperature or extreme environmental conditions.
  4. Damage resulting from connection to, or use of any accessory or other product not approved or authorized by the Company.
  5. Defects in appearance, cosmetic, decorative, or structural items such as framing and non-operating parts.
  6. Products damaged from external causes such as fire, dirt, sand, battery leakage, blown fuse, theft, or improper usage of any electrical source.

8.2 Technical Assistance

  • Website: https://www.xtoolonline.com
  • Email: support@xtoolonline.com
  • Address: Room 601, Block A, Zaoan Business Building, Shigu Road, Xili Residential District, Nanshan District, Shenzhen
  • Corporate & Business: business@xtoolonline.com, sales@xtoolonline.com

8.3 Compliance Information

8.3.1 FCC Compliance / FCC ID: 2AW3IP102

This device complies with Part 15 of the FCC rules and Industry Canada's license-exempt RSSs. Operation is subject to two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.

WARNING:

Changes or modifications not expressly approved by the responsible compliance authority could void the user's authority to operate the equipment.

NOTE:

This equipment has been tested and meets Class B digital device requirements under Part 15 of the FCC Rules, providing reasonable protection against interference in residential environments.

8.3.2 SAR (Specific Absorption Rate)

The device's emitted radio frequency power adheres to FCC regulations on exposure limits (capped at 1.6 W/kg). Minimize human contact during regular operation. SAR evaluations follow standard operational positions, with the device transmitting at its highest certified power level. Actual exposure tends to be lower as power output adjusts based on network requirements.

8.3.3 RoHS Compliance

This device complies with the European RoHS Directive 2011/65/EU, restricting hazardous substances in electrical and electronic equipment.

8.3.4 CE Compliance

This product conforms to the essential requirements of EMC Directive 2014/30/EU, R&TTE Directive 1999/5/EC, and Low Voltage Directive 2014/35/EU, bearing the CE mark.

9. User Tips

  • Global Version: The IP919 is a global version, meaning it should work in various regions like Mexico without specific regional limitations.
  • Language Updates: If you change the device language, remember to re-download the model software in the newly selected language for full functionality.
  • Wi-Fi for Updates: While not always needed for diagnostics, a stable Wi-Fi connection is crucial for software updates and for specific vehicle brands that require online server access.
  • Troubleshooting Charging: If the device isn't charging, try using the original cables and a stable 12V power supply. If the battery is very low, a long charge (6+ hours) might be needed.
  • VIN Entry: When manually entering a VIN, note that the letters Q, I, and O are typically grayed out on the keyboard because they are not used in standard VINs to avoid confusion with numbers.
  • Remote Support: For complex issues, XTOOL offers remote technical support via TeamViewer. Schedule an appointment with their engineers for assistance.

© 2025 XTOOL. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.