Hantek Hantek2000 Series

Contents

Hantek Handheld Oscilloscope 2000 Series User Manual

Models: 2C42, 2C72, 2D42, 2D72

1. Introduction

The Hantek 2000 Series Handheld Oscilloscope is a compact and lightweight 3-in-1 multifunction tester designed for engineers and enthusiasts. It integrates an oscilloscope, a signal source (waveform generator), and a digital multimeter into a single portable device. This manual provides detailed instructions for the safe and efficient operation of your Hantek 2000 Series device.

Video: Hantek Handheld Oscilloscope 2000 Series Product Overview and Unboxing.

2. Package Contents

Verify that all items listed below are included in your package. Contents may vary slightly depending on the specific model (2C42, 2C72, 2D42, 2D72).

  • 1x Hantek Handheld Oscilloscope Unit
  • 1x Passive Oscilloscope Probe (Models 2C42, 2C72) or 2x Passive Oscilloscope Probes (Models 2D42, 2D72)
  • 1x Crocodile Clip Test Line (Models 2C42, 2C72) or 2x Crocodile Clip Test Lines (Models 2D42, 2D72)
  • 1x Power Adapter (Charging Plug)
  • 1x Multimeter Leads
  • 1x USB Type-C Charging and Data Cable
  • 1x Carrying Case
  • 1x User's Guide
  • 1x Certification Card
Hantek Handheld Oscilloscope and included accessories

Image: Hantek Handheld Oscilloscope and included accessories.

3. Setup

3.1 Battery Installation

The device uses two 18650 replaceable lithium batteries. Ensure batteries are correctly inserted according to polarity markings.

Battery compartment showing two 18650 batteries

Image: Battery compartment with 18650 batteries.

3.2 Charging the Device

Connect the provided Type-C charging cable to the device's USB port and the power adapter. The device supports 5V/2A charging. You can use a standard mobile phone charger with a Type-C cable.

Device being charged via USB-C cable

Image: Device charging via USB-C.

3.3 Connecting Probes and Leads

The device features standard BNC connectors for oscilloscope probes (CH1, CH2, Gen Out) and banana plug inputs for multimeter leads (A, mA, COM, V/Ω/C/+).

Diagram of device ports including BNC and DMM inputs

Image: Device ports for oscilloscope and multimeter connections.

4. Operating Instructions

4.1 General Operation

The device features a minimalist keyboard design for ease of use. The suspending stand allows for multi-angle adjustment.

Hantek Handheld Oscilloscope with kickstand extended

Image: Device with kickstand for convenient viewing.

4.2 Oscilloscope Function

Press the 'Scope' button to enter oscilloscope mode. The device features a high-definition color LCD screen for clear waveform display. Use the navigation buttons to adjust settings like vertical resolution, time base, and trigger.

Oscilloscope display showing waveform and key indicators

Image: Oscilloscope display elements including trigger status, main time base window, trigger level, battery level, window displays waveform, channel marker, channel information, trigger time, and time base.

The 'Auto' button provides an automatic measuring function, identifying the type of waveform (sine or square wave) and adjusting settings accordingly. Cursor measurement functions support manual time and voltage measurements.

Diagram of oscilloscope controls and buttons

Image: Oscilloscope control buttons including Scope, DMM, AWG, Menu, Trig, Channel, Time, Enter, Auto, Power Key, Run/Stop.

4.3 Multimeter Function

Press the 'DMM' button to switch to digital multimeter mode. This function allows measurement of AC/DC voltage, current, resistance, capacitance, diode, and on-off tests. It offers high sensitivity and accuracy with a clear display.

Device displaying multimeter function with DC voltage reading

Image: Device displaying multimeter function with DC voltage reading.

4.4 Waveform Generator Function (2D42, 2D72 models only)

For models 2D42 and 2D72, press the 'AWG' button to access the waveform generator. It can output sine, square, triangle, and trapezoidal waveforms. The sine wave output can go up to 25MHz.

Device displaying waveform generator output settings

Image: Waveform generator output settings.

The Gen Out terminal of the oscilloscope without signal generator function always outputs a 2V @ 1KHz square wave, which can be used for probe calibration.

4.5 Menu and Language Settings

Press the 'Menu' button to access settings. You can switch the interface language between Chinese and English. Other settings include sound for button presses, backlight brightness, and backlight duration.

5. Firmware Update

It is recommended to update the device firmware to ensure optimal performance and resolve potential bugs. Firmware and programming tools are available on the manufacturer's website.

5.1 Entering DFU Mode

To update the firmware, the device must be in DFU (Device Firmware Upgrade) mode. While the device is powered off, hold down the 'F1' button and then power on the device. Connect the device to your computer via the USB Type-C cable.

5.2 Using the DFU Tool

Download the DFUSe Demo tool and the latest firmware file (.dfu) from the Hantek website. Open the DFUSe Demo tool, select the device in DFU mode, choose the firmware file, and click 'Upgrade'.

Screenshot of DFUSe Demo tool for firmware update

Image: Screenshot of the DFUSe Demo tool during firmware update.

5.3 Updating FPGA Firmware

For FPGA firmware updates, connect the powered-on device to your computer. Open the Hantek2000 PC software. Press the key combination Alt+Ctrl+Shift+F to open the FPGA Update dialog. Select the FPGA firmware file (.bin) and click 'Update'. Restart the device after the update is complete.

6. Maintenance

  • Keep the device clean and dry. Avoid exposure to dust, moisture, and extreme temperatures.
  • Use a soft, damp cloth to clean the exterior. Do not use abrasive cleaners or solvents.
  • Perform self-calibration periodically or if you notice any measurement discrepancies.
  • Store the device in its carrying case when not in use to protect it from physical damage.
Hantek carrying case

Image: Hantek carrying case for protection and portability.

7. Troubleshooting

  • Incorrect Readings/Glitches: Ensure the device firmware is up to date. Refer to Section 5 for firmware update instructions.
  • Probe Attenuator Issues: The attenuator switch on the probe (1X/10X) can be easily accidentally switched. Always verify its position before taking measurements.
  • Device Not Powering On: Check battery charge level. Ensure batteries are correctly installed.
  • Display Unclear: Adjust backlight settings in the menu.

8. Specifications

8.1 General Specifications

FeatureSpecification
Display Type2.8 inch 64K color TFT
Display Resolution320 horizontal by 240 vertical pixels
Display Size3.0 - 4.9 Inches
Power Supply100V-240VAC, 50Hz-60Hz; DC INPUT: 5VDC, 2A
Power Consumption<2.5W
Battery2600mA*2 (18650 replaceable lithium battery)
Operating Temperature0~50 °C (32~122 °F)
Storage Temperature-40~+71 °C (-40~159.8 °F)
Humidity≤+104°F (≤+40°C): ≤90% RH; ≤122°F (+41°C ~50°C): ≤60% RH
Cooling MethodConvection
AltitudeOperating and Nonoperating: 3,000m (10,000 feet)
Random Vibration0.310RMS from 5Hz to 500Hz, 10 minutes on each axis
Mechanical ShockNonoperating: 2.46gRMS from 5Hz to 500Hz, 10 minutes on each axis; Operating: 50g, 11ms, half sine
Dimension (L x W x H)199 x 98 x 40mm
Weight624g
CertificationCE

8.2 Oscilloscope Specifications

FeatureHantek2D72Hantek2D42Hantek2C72Hantek2C42
Channel2CH+DMM+AWG2CH+DMM+AWG2CH+DMM2CH+DMM
Bandwidth70MHz40MHz70MHz40MHz
Sample Rate Range250MSa/s (Single-channel), 125MSa/s (Dual-channel)
Waveform Interpolation(sin x)/x
Record LengthMax. 6K for single-channel; 3K samples per dual-channel
SEC/DIV Range5ns/div~500s/div 1, 2, 5 sequence
Vertical Resolution8-bit resolution, each channel sampled simultaneously
VOLTS/DIV Range10mV/div~10V/div at input BNC
Bandwidth Limit20MHz, typical
Low Frequency Response (-3dB)≤10Hz at BNC
Rise Time at BNC≤5ns
DC Gain Accuracy±3% for Normal or Average acquisition mode, 10V/div to 10mV/div
Acquisition ModesNormal
Trigger TypeEdge
Trigger ModeAuto, Normal, Single
Trigger Level±4 divisions from center of screen
InputCH1/CH2
CouplingDC, AC or GND
Input Impedance25pF±3 pF, 1MΩ±2%
Probe Attenuation1X, 10X
Supported Probe Attenuation Factors1X, 10X, 100X, 1000X
Maximum Input Voltage150VRMS

8.3 Multimeter Specifications

Measurement TermRangeAccuracyResolution
Maximum Resolution4000 Counts
DMM Testing ModesVoltage, Current, Resistance, Capacitance, Diode & On-Off
Maximum Input VoltageAC: 600V, DC: 800V
Maximum Input CurrentAC: 10A, DC: 10A
Input Impedance10MΩ
DC Voltage400.00mV±(0.8%+5)100uV
4.000V±(0.8%+5)1mV
40.00V±(0.8%+5)10mV
400.0V±(0.8%+5)100mV
600.0V±(1%+2)1V
Overload protection: 400mV: 250V, other: 600Vrms.
AC Voltage4.000V±(1.2%+5)1mV
40.00V±(1.2%+5)10mV
400.0V±(1.2%+5)100mV
600.0V±(1.5%+5)1V
Frequency: 40Hz~400Hz; Frequency of 400V and 600V: 40Hz~100Hz
DC Current40.00mA±(1%+2)10uA
200.0mA±(1.5%+2)100uA
4.000A±(1.8%+2)1mA
10.00A±(3%+2)10mA
Overload protection: self restoring fuse: 200mA/250V, 4A and 10A range no fuse.
Resistance400.0Ω±(1%+3)0.1Ω
4.000KΩ±(1%+3)1Ω
40.00KΩ±(1%+3)10Ω
400.0KΩ±(1%+3)100Ω
4.000MΩ±(1.5%+3)1KΩ
40.00MΩ±(1.5%+3)10KΩ
Overload protection: 220Vrms
Capacitance40.00nF±(3%+5)10pF
400.0nF±(3%+5)100pF
4.000uF±(3%+5)1nF
40.00uF±(3%+5)10nF
100.0uF±(3%+5)100nF
Overload protection: 220Vrms
Diode0V~1.0V
On-Off<50Ω

8.4 Waveform Generator Specifications

FeatureSpecification
Waveform Frequencies (Sine)1Hz~25MHz
Waveform Frequencies (Square)1Hz~10MHz
Waveform Frequencies (Ramp)1Hz~1MHz
Waveform Frequencies (EXP)1Hz~5MHz
Sampling250MSa/s
Amplitude2.5Vpp(50Ω) / 5Vpp(High impedance)
Frequency Resolution0.10%
Channel1CH waveform output
Waveform Depth512Sa

9. User Tips

  • Always ensure the device's firmware is updated to the latest version from the official Hantek website to benefit from bug fixes and performance improvements.
  • When using oscilloscope probes, be mindful of the 1X/10X attenuator switch. It can be easily moved, leading to incorrect readings if not set as expected.
  • The Type-C port is versatile; it handles both charging and data transfer to a PC.
  • Utilize the 'Auto' function in oscilloscope mode for quick and convenient waveform setup, especially for new users.
  • The device features a self-calibration function to maintain accuracy over time. Consult the full manual for detailed calibration steps.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official Hantek website or contact your authorized dealer. Keep your purchase receipt as proof of purchase.

© 2024 Hantek. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.