LAUNCH X431 ELITE V2.0

Contents

LAUNCH X431 ELITE V2.0 Car OBD2 Scanner User Manual

Model: X431 ELITE V2.0 | Brand: LAUNCH

1. Introduction

This diagnostic tool, the LAUNCH X431 ELITE V2.0, is specifically designed to work with all OBD II compliant vehicles, including those with Controller Area Network (CAN). It is required by the EPA that all 1996 and newer vehicles (cars and light trucks) sold in the United States must be OBD II compliant, covering American, Asian, and European vehicles.

A small number of 1994 and 1995 model year gasoline vehicles may also be OBD II compliant. To verify, check the Vehicle Emissions Control Information (VECI) Label, usually located under the hood or by the radiator. If the vehicle is OBD II compliant, the label will designate "OBD II Certified".

1.1 OBD II Definitions

The OBD II system monitors emission control systems and key engine components through continuous or periodic tests. It provides information on the Malfunction Indicator Light (MIL) status, Diagnostic Trouble Codes (DTCs), and Readiness Monitor status.

  • EOBD: European On-Board Diagnostics, similar to OBD II.
  • Communication Protocols: The tool supports CAN Bus, J1850 VPW, ISO 9141-2, J1850 PWM, and ISO 14230 KWP.
  • PCM (Powertrain Control Module): The vehicle's "on-board computer" controlling engine management, emissions, and powertrain.
  • DLC (Data Link Connector): A 16-cavity connector on the vehicle for communication with the diagnostic tool. Typically located within 12 inches of the instrument panel, under or around the driver's side.
  • MIL (Malfunction Indicator Light): The "Check Engine" warning light that illuminates when a DTC is stored.
  • DTC (Diagnostic Trouble Code): A five-digit alphanumeric code stored by the on-board computer, indicating a problem area. The first character identifies the control system (P=Powertrain, B=Body, C=Chassis, U=Network). The subsequent digits provide more specific information.
  • Freeze Frame Data: Operating conditions stored when a DTC is set.
  • PID (Parameter Identification Data): Data returned by the vehicle's control modules.
  • Monitors: Diagnostic routines in the PCM to run tests and ensure emissions-related components function correctly.
  • Enabling Criteria: Vehicle-specific events or conditions required for monitors to run diagnostic tests.
  • Trip: A driving period where all required Enabling Criteria for a specific monitor are met.
  • Drive Cycle: A specific mode of vehicle operation to set all applicable readiness monitors.
  • Warm-up Cycle: Vehicle operation after an engine off period where engine temperature rises from 40°F (22°C) to at least 160°F (70°C).
  • Fuel Trim (FT): Adjustments to the base fuel schedule (short-term for instantaneous, long-term for gradual changes).

1.2 Diagnostic Trouble Codes (DTCs) Structure

DTCs are stored by the on-board computer to identify specific problem areas. The structure is as follows:

Example: P0202 - Injector circuit malfunction, Cylinder 1

  • First Character (System): P=Powertrain, B=Body, C=Chassis, U=Network
  • Second Character (Code Type): 0=Generic (SAE), 1=Manufacturer Specific
  • Third Character (Sub-system): 1=Fuel/Air Metering, 2=Fuel/Air Metering, 3=Ignition System/Misfire, 4=Auxiliary Emission Controls, 5=Vehicle Speed/Idle Control/Auxiliary Inputs, 6=Computer/Auxiliary Outputs, 7/8/9=Transmission
  • Fourth & Fifth Characters: Specific fault identification.

2. Product Overview

The LAUNCH X431 ELITE V2.0 is a powerful diagnostic tool designed for efficient car repairs. It features a 4-inch touch screen, Android 8.1 OS, and supports 11 languages.

Video: Unboxing and initial setup of the LAUNCH X431 Elite V2.0 diagnostic tool, showing the main unit, OBD diagnostic cable, user manual, and quick start guide. It also demonstrates connecting the device and powering it on.

2.1 Components & Controls

Main unit and OBD diagnostic cable

Image: The main unit of the LAUNCH X431 ELITE V2.0 diagnostic tool alongside its OBD diagnostic cable.

No.NameDescriptions
1Charging portCharge the tool via data cable (not included).
2DB-15 diagnostic connectorConnect the diagnostic cable.
3Power buttonTurn on/off the tool.
4Touch screenIndicate the test results.
5BACK buttonExit the current program or return to the previous screen.
6HOME buttonNavigate to the home (Job menu) screen.
7Settings buttonQuick dial to the Settings module.

2.2 Technical Specifications

  • Screen: 4" touch screen with a resolution of 480*800
  • CPU: 4-core 1.3GHz processor
  • RAM: 2GB
  • ROM: 16GB
  • WiFi: 802.11b/g/n 2.4GHz
  • OBD II input voltage range: 9~18V
  • Power up via: DC 5V data cable (not included) or Diagnostic cable through connection to vehicle's DLC
  • Working temperature: -10 to 50°C (14 to 122 F°)
  • Storage temperature: -20 to 70°C (-4 to 158 F°)

2.3 Accessories Checklist

For detailed accessory items, please consult the seller. Typically includes:

  1. Diagnostic scanner (Main Unit)
  2. Diagnostic cable
  3. User manual
  4. Quick start guide

3. Initial Use

3.1 Powering Up The Tool

The tool can be powered up in two ways:

  • Via Data Cable: Plug one end of a data cable (not included) into the charging port of the tool, and the other end to a PC.
  • Via Diagnostic Cable: Insert the diagnostic cable into the vehicle's DLC port. The screen will automatically light up when powered on.

3.2 Getting Started (First-Time Setup)

For first-time use, follow these steps to configure system settings:

  1. Press the [POWER] button to turn on the tool. Tap "Start" on the welcome page.
  2. Choose your desired system language and tap "Next step".
  3. Select your current time zone. The system will automatically configure the time.
  4. The system will search for available Wi-Fi networks. Choose and connect to a Wi-Fi network.
  5. After network connection, tap "Next step" to configure workshop information. Input the required details. (Note: This information will be appended to every generated report.)
  6. Read the user agreement, check "Agree to all the above terms", and tap "OK" to complete registration. The tool will then automatically go to the Job Menu.

3.3 Job Menu Overview

The Job Menu includes the following main function modules:

  • Diagnose: Configures the tool for professional diagnostic operations.
  • OBD II: Provides quick checks for DTCs, MIL status, readiness monitors, and other emission-related services.
  • Upgrade: Updates vehicle diagnostic software and APK. Requires a stable network connection.
  • Mall: Allows subscription to extra vehicle diagnostic software or reset (special function) software not pre-installed.
  • Settings: Manages data and system settings like Network setup, Workshop information, and Brightness.

4. Diagnosis

4.1 Connection

  1. Turn the vehicle's ignition off.
  2. Locate the vehicle's 16-pin Data Link Connector (DLC).
  3. Plug one end of the diagnostic cable into the vehicle's DLC port and the other end into the DB-15 diagnostic connector of the tool. Tighten the captive screws. (Note: A plastic DLC cover may need to be removed. The cable connector is keyed and fits only one way.)
  4. Turn the ignition on. The engine can be off or running.

Caution: Do not connect or disconnect any test equipment with the ignition on or engine running.

4.2 System Diagnosing

This function diagnoses electronic control systems of a single vehicle model.

  • Diagnostic software includes reset functions (select "Special function" from the diagnostic function list).
  • Software updates are periodic. It is recommended to install the latest version.
  • Pre-installed diagnostic software updates are free forever.
  • Software purchased from the "Mall" includes one year of free updates; renewal is required after expiration.
  • More vehicle coverage can be extended via the "Mall".

4.2.1 Smart Diagnosis (Auto-Detect)

This function quickly accesses vehicle electronic control systems by decoding the VIN, eliminating manual menu selection. After connection, turn the ignition key on, and the system enters auto-detect mode.

  • Ensure "Automatic detection on connect" in "Settings" is ON.
  • A stable network connection is recommended for successful VIN access.

If the system successfully obtains the VIN, it will scan vehicle systems and automatically generate a diagnostic report (accessible via Settings -> Data -> Diagnostic Report).

If VIN information cannot be accessed, the tool will prompt for manual VIN input or enter Manual Diagnosis mode.

4.2.2 Manual Diagnosis

If auto-detect fails, you can perform Manual Diagnosis by executing menu-driven commands. The diagnostic menu varies by vehicle make, model, and year.

  • Ensure the corresponding vehicle manufacturer software is installed.

4.2.2.1 Health Report (Quick Test)

This function quickly accesses all electronic control units and generates a detailed vehicle health report. Tap "Health Report" to start scanning. Once complete, the report will display systems with fault codes (red cross) and systems with no issues (green tick).

  • Report: Save diagnostic results as a report.
  • Clear Code: Clear existing diagnostic trouble codes.

4.2.2.2 System Scan

Quickly scans which systems are installed on the vehicle.

4.2.2.3 System Selection

Manually select the test system and function step-by-step. Tap "System Selection", then choose the desired system (e.g., "Engine") to access test functions.

A. Read Fault Code

Displays detailed information of DTCs retrieved from the vehicle's control system.

  • Help: View help information.
  • Code Search: Search for more information about the current DTC online.
  • Report: Save current data in text format. Accessible via Settings -> Data -> Diagnostic Report.

B. Clear Fault Code

Erases codes from the vehicle after repairs. Ensure the ignition key is ON and the engine is OFF before performing this function.

  • Do not erase codes if taking the vehicle to a service center, as valuable diagnostic information may be lost.
  • Clearing codes does not fix the underlying problem; proper repairs are necessary to prevent codes from reappearing.

C. Read Data Stream

Retrieves and displays live data and parameters from the vehicle's ECU. After selecting desired items, tap "OK" to view the data stream.

4-in-1 Live Data Graphing and Diagnostic Report

Image: Screen demonstrating 4-in-1 Live Data Graphing, Data Record & Playback, Diagnostic Report Share & Print, and Online Feedback features.

  • Values out of range are displayed in red.
  • The screen indicates current page/total page number (e.g., 1/X). Swipe to navigate.
  • Display Modes:
    • Value: Displays parameters with numbers and lists.
    • Graph: Displays parameters with wave patterns.
    • Combine: Merges up to 4 graphs for easier comparison.
  • Report: Save current data as a diagnostic report.
  • Record: Record and save Live Data for troubleshooting.

D. Special Functions

Offers coding, reset, relearn, and other service functions to restore vehicle functionality after repair or replacement. Available tests vary by vehicle manufacturer, model, and year.

All Service Functions and Reset options

Image: Overview of various service functions and reset options available, including Oil Reset, Parking Brake, Injector Coding, SAS Calibration, Battery Replacement, Key Programming, TPMS Reset, and more.

Advanced ECU Coding features

Image: Advanced ECU Coding features, showing options for Component Matching, ECU Replacement, Retrofit/Modification, and Flash Hidden Functions, with examples like Rear Mirror Folding and A/C Settings Memory.

4.3 OBD II Diagnosis Functions

After connecting the tool and tapping "OBD II" in the Job Menu, the tool will automatically check the communication protocol and display Monitor Status. Tap "OK" to see the function list:

  1. Read Codes: Identifies malfunctioning sections of the emission control system.
  2. Erase Codes: Erases codes after repairs. Ensure ignition is ON, engine OFF.
  3. I/M Readiness: Checks if emission-related systems are operating properly and ready for Inspection and Maintenance testing.
  4. Data Stream: Retrieves and displays live data and parameters from the ECU.
  5. View Freeze Frame: Shows a snapshot of operating conditions when an emission-related fault occurs.
  6. O2 Sensor Test: Retrieves O2 sensor monitor test results.
  7. On-board Monitor Test: Retrieves test results for non-continuously monitored powertrain components.
  8. EVAP System Test: Initiates a leak test for the vehicle's EVAP system.
  9. Vehicle Info: Retrieves VIN, CID (Calibration ID), and CVN (Calibration Verification Number).

4.4 History

The tool records details of each diagnostic session. The History function provides direct access to previously tested vehicles, allowing users to resume operations without starting from scratch. Diagnostic records are listed in date sequence.

5. Upgrade

This function allows you to update the diagnostic app and software. All software is updated periodically for best service and experience.

5.1 Update Diagnostic Software & App

Tap "Upgrade" on the Job menu to enter the update center.

  • Pre-installed diagnostic software updates are free forever.
  • Diagnostic software purchased from the "Mall" includes one year of free updates.

To update:

  1. Tap "Upgrade" on the Job menu.
  2. By default, all diagnostic software is selected. To deselect, tap "Unselect" and uncheck the box next to the vehicle model.
  3. Tap "Update" to start downloading. This may take several minutes.
  4. Once downloaded, software packages will install automatically.

Note: Ensure a strong and stable Wi-Fi connection during updates.

5.2 Renew Subscription

When the free update period for purchased software expires, it will be locked. To unlock, renew the subscription.

  1. Tap "Upgrade" on the Job menu.
  2. Expired software is displayed in gray. Select the desired software and tap "Renew".
  3. Input the 24-digit PIN code from your Subscription Renewal Card (purchased separately) and tap "Submit".

Note: A single Subscription Renewal Card is applicable to one software, not all software installed on the tool.

6. Settings

The Settings menu allows you to customize various aspects of the tool's operation.

6.1 General Settings

  • Units of measurement: Set to Metric System or English System.
  • Automatic detection on connect: Enable/disable automatic VIN detection when connected to the vehicle's DLC.
  • Brightness: Adjust screen brightness and standby time. (Reducing brightness conserves power.)
  • Sound: Adjust volume and other sound settings.
  • Network: Configure WLAN for registration, software updates, and email.
  • Time Zone: Set the device's time zone.
  • Language: Change the operating language. The tool supports multiple languages, including English, Traditional Chinese, Spanish, French, German, Italian, Russian, Portuguese, Japanese, Korean, and Polish.
  • Workshop information: Add a personalized tag to diagnostic reports.
  • Recovery: Reset the tool to default factory settings. (Warning: This may cause data loss.)
  • Clean Up: Clear cache files to free up storage space.
  • Screen Capture: Toggle the Screen Capture icon visibility.
  • About: Displays hardware configuration and license agreement.

6.2 Data Management (7.13 Data)

  • Diagnostic Record: Stores running parameters and waveform graphs.
  • Diagnostic Report: Stores all generated diagnostic reports.
  • DTC Library: Provides details of DTCs to simplify diagnosis.
  • DLC (Data Link Connector) Location: Helps find the vehicle's DLC location.
  • Feedback: Send diagnostic problem feedback for analysis.
  • Image: View and manage screenshots taken during diagnostic work.
  • Firmware Fix: Upgrade and fix diagnostic firmware. (Do not cut power or switch interfaces during fixing.)
  • User Manual: The user manual is integrated into the tool for easy access.

7. Troubleshooting (FAQ)

Here are some frequently asked questions and their solutions:

  1. System halts when reading data stream. What is the reason?
    This may be caused by a slackened connector. Turn the tool off, firmly connect the connector, and switch it on again.
  2. Screen of the tool flashes at engine ignition start.
    This is caused by electromagnetic disturbing and is a normal phenomenon.
  3. There is no response when communicating with on-board computer.
    Confirm the proper voltage of the power supply. Check if the throttle has been closed, the transmission is in neutral, and the water is at proper temperature.
  4. What to do if the system fails to start auto VIN detection?
    Check the following:
    • Whether the tool is properly connected to the vehicle's DLC port.
    • Whether the "Automatic detection on Connect" switch in Settings is OFF. If it is, slide it to ON.
  5. Why are there so many fault codes?
    Usually, this is caused by poor connection or fault circuit grounding.
  6. How to upgrade the system?
    1. Switch the tool on and ensure a stable internet connection.
    2. Tap "Settings" on the Job Menu, select "About" -> "Version", and tap "Detect the System Version" to enter the system upgrading page.
    3. Follow the on-screen instructions to finish the process. It may take several minutes. After the upgrade is successfully finished, the tool will automatically restart and enter the Job menu.

8. Specifications

AttributeValue
Communication InterfaceOBD-II
Software UpdateYes
High-concerned chemicalNone
UseNot Telecommunication
ElectronicYes
Wireless SupportWifi
Is Batteries IncludedYes
Special FeaturesWifi
Model NameX431 ELITE V2.0
Software Version2026 Version
Hardware Version2026 Version
Brand NameLAUNCH
OriginMainland China
Power (W)5V 1.5A 7.5W
Screen4" touch screen, 480*800 resolution
CPU4-core 1.3GHz processor
RAM2GB
ROM16GB
Working Temperature-10 to 50°C (14 to 122 F°)
Storage Temperature-20 to 70°C (-4 to 158 F°)

9. Warranty & Support

9.1 Warranty Information

LAUNCH® electronic products are warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user. This warranty is limited to persons who purchase LAUNCH® products for purposes of resale or use in the ordinary course of the buyer's business.

The warranty does not cover parts that have been abused, altered, used for unintended purposes, or used inconsistently with instructions. The exclusive remedy for a defective automotive meter is repair or replacement. LAUNCH is not liable for consequential or incidental damages.

Final determination of defects will be made by LAUNCH according to stipulated procedures.

9.2 Order Information (Replaceable & Optional Parts)

Replaceable and optional parts can be ordered directly from your authorized tool supplier. Your order should include:

  • Quantity
  • Part number
  • Item description

9.3 Customer Service

If you have any questions on the operation of the unit, please contact the seller or LAUNCH TECH CO., LTD. via:

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.