Diatone MAMBA F45/F55/F65_128K

Contents

Diatone MAMBA F45/F55/F65_128K Flight Controller and 4-in-1 ESC Instruction Manual

Model: MAMBA F45/F55/F65_128K | Brand: Diatone

1. Introduction

The Diatone MAMBA F45/F55/F65_128K series offers high-performance Flight Controller (FC) and 4-in-1 Electronic Speed Controller (ESC) stacks designed for FPV racing drones. These units integrate advanced features and robust construction to provide reliable and precise control for your aircraft. This manual will guide you through the installation, configuration, and operation of your MAMBA stack.

2. Specifications

2.1 General Specifications

  • Material: Metal
  • Origin: Mainland China
  • Recommended Age: 14+ years
  • Use: Vehicles & Remote Control Toys (specifically FPV Racing Drones)
  • Is Electric: No Battery (refers to the unit itself, not requiring internal batteries)
  • Is it battery/power supply: No
  • Is it charger/adapter: No
  • Is Batteries Included: No
  • High-concerned chemical: None

2.2 Model-Specific Specifications

FeatureMAMBA F45A 128KMAMBA F55A 128KMAMBA F65A 128K
Input Voltage3~6S Lipo (12.6V~25.2V)3~6S Lipo (12.6V~25.2V)3~6S Lipo (12.6V~25.2V)
Rated Current45A×455A×465A×4
Peak Current (10S)55A65A75A
BECNoNoNo
FirmwareBLHeli_32 MAMBA F45_128KBLHeli_32 MAMBA F55_128KBLHeli_32 MAMBA F65_128K
ProgramDshot300/600/1200Dshot300/600/1200Dshot300/600/1200
PWM Frequency24~128K24~128K24~128K
TVS Power ProtectionYesYesYes
Mounting Hole30.5mm/M330.5mm/M330.5mm/M3
Included Accessories8pin sh1.0 ×2, AMASS Original XT60, High frequency capacitor 470uF/35V8pin sh1.0 ×2, AMASS Original XT60, High frequency capacitor 470uF/35V8pin sh1.0 ×2, AMASS Original XT60, High frequency capacitor 470uF/35V

3. Setup and Installation

Proper installation is crucial for the performance and safety of your FPV drone. Always ensure power is disconnected before handling components.

3.1 Mounting

The MAMBA FC/ESC stack features a standard 30.5mm/M3 mounting pattern. Securely mount the stack to your drone frame using appropriate standoffs and screws. Ensure no components are shorting against the frame or other electronics.

3.2 Wiring and Soldering

The ESC features large soldering pads for easier and more reliable connections. Refer to the wiring diagram provided with your flight controller for specific connections to motors, power distribution, and other peripherals.

Bottom view of MAMBA ESC showing large soldering pads
Figure 1: Bottom view of the MAMBA ESC, highlighting the large soldering pads for robust connections.
Top view of MAMBA ESC showing large soldering pads and main components
Figure 2: Top view of the MAMBA ESC, illustrating the layout of components and soldering pads.
Angled view of MAMBA ESC showing connectors and soldering pads
Figure 3: Angled view of the MAMBA ESC, detailing the various connectors and soldering points.

Use the provided 8pin sh1.0 connectors for connecting the FC to the ESC. The AMASS Original XT60 connector is for main battery power input. A high-frequency capacitor (470uF/35V) is included and should be soldered to the main battery pads for power filtering.

3.3 Initial Configuration

Connect the flight controller to your computer via USB. Use Betaflight Configurator (or similar software for your FC) to flash the appropriate firmware and configure settings such as motor protocols (Dshot300/600/1200), PID tuning, and receiver setup. Ensure the BLHeli_32 firmware on the ESC is up to date and configured correctly for your motors.

4. Operating Instructions

Once installed and configured, your MAMBA stack is ready for operation. Always perform pre-flight checks.

  • Power On: Connect your 3-6S Lipo battery to the XT60 connector. The FC and ESC will power up.
  • Arming: Arm your drone using your radio transmitter as configured in Betaflight. Ensure propellers are clear before arming.
  • Flight: Operate your FPV drone according to standard FPV flying practices. The high PWM frequency (24~128K) of the ESCs provides smooth and responsive motor control.
  • Disarming: Disarm your drone after landing. Disconnect the battery when not in use.

5. Maintenance

Regular maintenance helps prolong the life of your MAMBA stack.

  • Visual Inspection: Periodically inspect the board for any signs of damage, loose connections, or debris.
  • Cleaning: Gently clean the board with isopropyl alcohol and a soft brush if dust or dirt accumulates. Ensure the board is completely dry before reapplying power.
  • Connection Check: Verify all soldered connections are secure and free from cold joints or shorts.
  • Firmware Updates: Keep your FC and ESC firmware updated to benefit from performance improvements and bug fixes.

6. Troubleshooting

If you encounter issues, consider the following common troubleshooting steps:

  • No Power: Check battery connection, XT60 connector, and main power leads for continuity.
  • Motors Not Spinning: Verify motor connections, ESC calibration, and motor direction in Betaflight/BLHeli_32 configurator. Ensure the drone is armed.
  • Erratic Flight: Recheck FC mounting for vibrations, recalibrate accelerometers, and review PID settings.
  • Smoke/Burning Smell: Immediately disconnect power. This indicates a short circuit or component failure. Inspect for damaged components or incorrect wiring. The integrated TVS power protection helps mitigate damage from voltage spikes, but severe issues still require immediate power disconnection.
  • Connection Issues (USB): Try a different USB cable or port. Ensure correct drivers are installed for your flight controller.

7. User Tips

  • Soldering Quality: Given the 'Super Big Soldering Pad' feature, take advantage of the extra space for clean and strong solder joints. Poor soldering is a common cause of FPV drone issues.
  • Power Filtering: Always install the included high-frequency capacitor on the main battery pads to reduce electrical noise and protect your electronics.
  • Voltage Monitoring: Pay attention to your Lipo battery's voltage range (3-6S) to prevent over-discharge or over-charge, which can damage the ESC and battery.
  • Component Protection: Consider using conformal coating on your electronics for added protection against moisture and dust, especially if flying in varied conditions.

8. Warranty and Support

For technical support, warranty claims, or further assistance, please contact the seller or manufacturer directly. Keep your purchase records handy when seeking support.

© 2023 Diatone. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.