Cytron MDD10A

Contents

Cytron MDD10A Dual Channel 10Amp DC Motor Driver

User Manual

1. Product Overview

The Cytron MDD10A is a dual-channel DC motor driver designed to control two independent brushed DC motors. This Rev2.0 version, shipped after January 2017, supports a motor voltage (Vmotor) range of 5V to 30VDC. It is capable of driving motors with a continuous current of up to 10A per channel and a peak current of 30A (for 10 seconds).

The MDD10A utilizes full solid-state components, ensuring faster response times and eliminating the wear and tear associated with mechanical relays. It supports both Locked-Antiphase and Sign-Magnitude PWM signals for precise motor control. The driver is compatible with popular microcontrollers like Arduino and Raspberry Pi, accepting logic signals at 3.3V or 5.0V.

Integrated manual/test buttons allow for quick activation and testing without the need for an external microcontroller, making initial setup and debugging straightforward.

2. Package Contents

Please verify that all items are present in your package:

  • 1 x MDD10A Rev2.0 Motor Driver Board
  • 1 x 2510 PCB connector - 5 ways female
  • 5 x 2510 terminal pins
Angled view of the MDD10A motor driver board

Figure 1: Angled view of the MDD10A motor driver board.

Top-down view of the MDD10A motor driver board

Figure 2: Top-down view of the MDD10A motor driver board.

3. Setup and Connections

Before connecting any components, ensure all power sources are disconnected. The MDD10A does NOT have reverse polarity protection for the motor voltage (Vmotor). Double-check all connections before applying power.

3.1 Wiring Diagram

MDD10A Wiring Diagram showing motor, power, and control signal connections

Figure 3: MDD10A Wiring Diagram. This diagram illustrates connections for two DC brushed motors, the Vmotor input (5-30VDC), output indicator LEDs, manual/test buttons, power indicator LED, and control signal inputs (3.3V to 5.0V logic).

3.2 Power Connections

  • Vmotor Input: Connect your DC power supply (5V to 30VDC) to the Vmotor input terminals. Ensure correct polarity.
  • Motor Connections: Connect your DC brushed motors to the designated Motor 1 and Motor 2 output terminals. Each motor should be a two-terminal DC brush motor.

3.3 Control Signal Input

The MDD10A accepts control signals from microcontrollers such as Arduino or Raspberry Pi. The logic level for these signals can be 3.3V or 5.0V.

  • PWM (Pulse Width Modulation): Used for speed control. The input PWM frequency can be up to 20KHz.
  • DIR (Direction): Used for direction control.
  • The driver supports two independent channels, allowing separate control of each motor.

3.4 Compatible Motors

The MDD10A is suitable for DC brush motors that meet the following criteria:

  • Two-terminal DC brush motor.
  • Operating voltage from 5V to 30V.
  • Rated Continuous Current ≤ 10A.
  • Peak Current ≤ 30A.

Examples of suitable motor series include SPG50, SPG30/SPG30E, IG45, IG42, IG32, and DKM 40W series.

4. Operating Instructions

The MDD10A offers flexible control options for your DC brushed motors.

4.1 Manual Operation / Fast Test

The board includes two activation buttons, one for each channel. These buttons allow for quick manual activation or testing of the motors without requiring a microcontroller. This is useful for verifying motor functionality and wiring during initial setup.

4.2 Microcontroller Control

To control the motors using a microcontroller (e.g., Arduino, Raspberry Pi):

  1. Connect Control Signals: Connect the PWM and DIR pins from your microcontroller to the corresponding input pins on the MDD10A.
  2. Speed Control: Apply a PWM signal to the PWM input pin. The duty cycle of the PWM signal will determine the motor's speed. The MDD10A supports PWM frequencies up to 20KHz.
  3. Direction Control: Apply a logic HIGH or LOW signal to the DIR input pin to control the motor's rotation direction.
  4. PWM Modes: The MDD10A supports both Locked-Antiphase and Sign-Magnitude PWM operation. Consult your microcontroller's documentation or Cytron's resources for implementing these modes. Note that this is not 'RC PWM'.

4.3 Indicator LEDs

  • Power Indicator LED: Illuminates when power is supplied to the board.
  • Output Indicator LEDs: Provide visual feedback on the motor output status for each channel.

5. Maintenance

The Cytron MDD10A is designed for durability and low maintenance due to its solid-state components and efficient design.

  • Cleaning: Keep the board free from dust and debris. Use a soft, dry brush or compressed air for cleaning.
  • Environment: Operate the driver in a dry environment, away from moisture and extreme temperatures.
  • Heat Management: The fully NMOS H-Bridge design provides excellent efficiency, and typically no additional heat sink is required under normal operating conditions. Ensure adequate airflow around the board if operating at continuous high loads.
  • Physical Inspection: Periodically inspect the board for any signs of physical damage or loose connections.

6. Troubleshooting

  • Board does not power on:
    • Check the Vmotor input voltage (5V-30VDC).
    • CRITICAL: Verify the polarity of the Vmotor connection. The MDD10A does not have reverse polarity protection, and incorrect connection can damage the board.
    • Ensure the power supply is providing sufficient current.
  • Motor does not spin or spins erratically:
    • Check motor connections to the MDD10A.
    • If using a microcontroller, verify that PWM and DIR signals are correctly connected and being sent.
    • Ensure the logic level of your control signals (3.3V or 5.0V) matches the MDD10A's compatibility.
    • Test the motor independently to ensure it is functional.
    • Use the on-board manual/test buttons to quickly check if the motor driver outputs are working.
    • Confirm the motor's current draw and voltage requirements are within the MDD10A's specifications (10A continuous, 30A peak, 5V-30VDC).
  • Motor driver gets hot:
    • While no heat sink is typically required, excessive heat can indicate an overload. Check if the motor's current draw exceeds 10A continuous or 30A peak.
    • Ensure adequate ventilation around the board.

7. Specifications

Feature Specification
Motor Channels 2 (Dual Channel)
Motor Type Brushed DC Motors
Motor Voltage (Vmotor) 5V to 30VDC (Rev2.0)
Continuous Current (per channel) 10A
Peak Current (per channel) 30A (for 10 seconds)
Logic Level Input 3.3V and 5V (compatible with Arduino, Raspberry Pi)
PWM Frequency Up to 20KHz
PWM Operation Modes Locked-Antiphase, Sign-Magnitude
H-Bridge Type Fully NMOS
Braking Regenerative Braking
Dimensions 84.5mm x 62mm
Reverse Polarity Protection (Vmotor) None

8. User Tips

  • Always Double-Check Polarity: Due to the lack of reverse polarity protection on Vmotor, make it a habit to verify your power connections multiple times before applying power to prevent damage.
  • Utilize Test Buttons: The on-board manual/test buttons are invaluable for quick verification of motor and driver functionality. Use them to isolate issues during troubleshooting before involving complex microcontroller code.
  • Match Logic Levels: Ensure your microcontroller's output logic voltage (3.3V or 5V) is correctly configured and compatible with the MDD10A's control signal inputs.
  • Consider Motor Specifications: Always ensure your chosen DC motors fall within the voltage and current limits of the MDD10A to ensure optimal performance and longevity of both the driver and the motors.

9. Warranty and Support

For detailed warranty information, technical support, and additional resources, please refer to the official Cytron Technologies website or contact their customer service. Keep your purchase receipt for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.