Nobleza Automatic Pet Waterer

Introduction

Thank you for choosing the Nobleza Automatic Pet Waterer. This innovative device is designed to provide your beloved pets with a continuous supply of fresh, filtered water, encouraging healthy hydration habits. Featuring a cordless design, motion sensor, and a long-lasting rechargeable battery, it offers convenience and peace of mind. Please read this manual carefully before use to ensure proper operation and maintenance.

Package Contents

Please check the package to ensure all components are present:

• Main Waterer Unit (4L Water Storage Tank)
• Stainless Steel Drinking Basin
• Water-tap
• Water Pump
• Connecting Pipe
• Filter Tray
• Filter Element (Pre-filter Sponge, Non-woven Fabric, Activated Carbon)
• Charging Cable (not explicitly listed but implied by rechargeable battery)

Figure 1: Parts Drawing of the Pet Water Dispenser

Setup and Assembly

1. Initial Charge: Before first use, fully charge the waterer's built-in 4000mAh rechargeable battery. Connect the charging cable to the charging port (usually located on the control panel) and a suitable power source. The indicator light will show charging status.
2. Assemble the Water Pump: Place the water pump securely into its designated slot within the 4L water storage tank.
3. Install the Connecting Pipe: Attach the connecting pipe to the water pump outlet.
4. Place the Filter Tray: Position the filter tray over the water pump and connecting pipe.
5. Insert Filter Elements: Place the filter elements (pre-filter sponge, non-woven fabric, activated carbon) into the filter tray as shown in the maintenance section. Ensure they are correctly seated.
6. Attach the Water-tap: Secure the water-tap onto the top of the connecting pipe.
7. Position the Stainless Steel Drinking Basin: Place the stainless steel drinking basin on top of the main unit, ensuring it aligns properly with the water-tap and covers the filter tray.
8. Fill with Water: Fill the 4L water storage tank with clean water. Do not overfill.

Operating Instructions

The Nobleza Automatic Pet Waterer offers two operating modes and smart indicators for ease of use.

Power On/Off

• To power on, press and hold the power button (usually located on the control panel) until the indicator lights activate.
• To power off, press and hold the power button again.

Mode Selection

The waterer features two modes to suit your pet's drinking habits. Use the mode selection button (often integrated with the power button or a separate button on the control panel) to switch between modes.

• Sensor Mode: In this mode, the water flow is activated for 6 seconds when your pet is detected within 5 feet (approximately 1.5 meters) of the waterer. This mode conserves battery life, offering up to 90 days of use on a single charge.
• Intermittent Mode: In this mode, water flows for 15 seconds every 15 minutes, repeating the cycle. This provides a regular flow of water without relying on motion detection. This mode offers approximately 45 days of battery life.

Figure 2: Operating Modes - Sensor Mode and Intermittent Mode

Smart Indicator Lights

• Low Water Alert: When the water level in the tank is low, the built-in LED light will change from blue to red, indicating that water needs to be refilled.
• Low Battery Alert: When the battery is low and needs charging, the sensors on the fountain will flash red continuously.

Maintenance and Cleaning

Regular cleaning and filter replacement are essential for your pet's health and the longevity of the waterer.

Filter Replacement

For your pet's health, it is recommended to change the filter every 2-4 weeks, depending on usage and water quality.

1. Remove the stainless steel drinking basin and filter tray.
2. Discard the old filter elements (pre-filter sponge, non-woven fabric, activated carbon).
3. Rinse the new filter elements thoroughly under running water before installation.
4. Place the new filter elements into the filter tray in the correct order: Pre-filter Sponge, Non-woven Fabric, Activated Carbon, followed by another Non-woven Fabric layer.
5. Reassemble the filter tray and drinking basin.

Figure 3: Multi-Filtration System Components

Cleaning the Waterer

Clean the waterer at least once a week to prevent bacterial growth and maintain water quality.

1. Unplug the waterer (if charging) and remove all water.
2. Disassemble the stainless steel drinking basin, water-tap, connecting pipe, filter tray, and water pump.
3. Wash all removable parts with mild soap and water. Rinse thoroughly to remove any soap residue.
4. Clean the inside of the 4L water storage tank.
5. Gently clean the water pump according to its specific instructions (usually involves disassembling the impeller cover and cleaning the impeller).
6. Ensure all parts are completely dry before reassembling.

Troubleshooting

• Water not flowing:
  • Check if the water tank has enough water.
  • Ensure the battery is charged.
  • Verify the water pump is correctly installed and not obstructed.
  • Clean the water pump and filter elements for any debris.
• Indicator light is red (low water): Refill the water tank to the appropriate level.
• Indicator light is flashing red (low battery): Charge the waterer using the provided charging cable.
• Excessive noise:
  • Ensure the water level is sufficient.
  • Clean the water pump, especially the impeller, as debris can cause noise.
  • Check that all parts are assembled correctly and securely.
• Motion sensor not detecting: Ensure there are no obstructions in front of the sensor and that the waterer is placed in an area where the pet can approach within 5 feet.

Specifications

Figure 4: Capacity, Battery, and Dimensions

Figure 5: Quiet Operation (Less than 30 dB)

User Tips

• Placement: Due to its cordless design, you can place the waterer anywhere your pet prefers, encouraging them to drink more. Consider locations away from direct sunlight to keep water cooler.
• Acclimation: Some pets may need time to adjust to a new water source. Encourage them gently and ensure they have access to their old water source during the transition.
• Filter Maintenance: Regularly check the pre-filter sponge for hair and debris, as this can extend the life of the main filter and pump.
• Battery Management: If you're going on a short trip, ensure the waterer is fully charged. For longer absences, consider having someone check on the water level and battery.
• Water Quality: Always use clean, fresh water. Avoid using hard water if possible, as it can lead to mineral buildup and affect pump performance.

Warranty and Support

For warranty information, please refer to the terms and conditions provided by your retailer or the manufacturer at the time of purchase. Keep your proof of purchase for any warranty claims.

If you encounter any issues or have questions not covered in this manual, please contact the seller or Nobleza customer support for assistance. Ensure you have your product model and purchase details ready when contacting support.