Introduction
The Liectroux ZK901 is an advanced wet dry sweeping robot vacuum cleaner designed to provide efficient and comprehensive floor cleaning. Equipped with laser navigation, SLAM algorithm, and a 450ml water tank, it offers intelligent mapping, precise cleaning, and both vacuuming and mopping functionalities. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your device to ensure optimal performance and longevity.
Setup
Unpacking and Initial Placement
- Carefully remove all components from the packaging. Ensure all accessories listed in the 'Product Configuration List' are present.
- Place the charging station against a wall in an open area, ensuring there are no obstacles within 1 meter to the sides and 2 meters in front of it. Connect the power adapter to the charging station and plug it into a power outlet.
- Remove any protective films or stickers from the robot vacuum cleaner.
Charging the Robot
Before first use, fully charge the robot. Place the robot onto the charging station, ensuring the charging contacts align. The indicator lights on the robot will show the charging status. A full charge typically takes several hours.
Installing Side Brushes and Main Brush
- Turn the robot upside down.
- Snap the side brushes into their designated slots (L for left, R for right).
- Ensure the main V-shaped roller brush is securely installed in its compartment.
Water Tank and Dustbin Installation
- Open the robot's top cover to access the dustbin compartment.
- For dry sweeping, ensure the dustbin with double filters is correctly inserted.
- For wet mopping, fill the 450ml water tank with clean water. Attach the mop cloth to the water tank bracket and then slide the assembly into the robot.
Operating Instructions
Power On/Off
Press and hold the power button on the robot for a few seconds to turn it on or off. The robot will emit a voice prompt.
Starting a Cleaning Cycle
- Manual Start: Press the clean button on the robot once to start an automatic cleaning cycle.
- App Control: Download the Liectroux app. Follow the in-app instructions to connect your robot. From the app, you can start/stop cleaning, select cleaning modes, set schedules, and define virtual blockers.
Cleaning Modes
The ZK901 offers various cleaning modes, selectable via the app:
- Auto Cleaning: The robot intelligently plans a zigzag route for comprehensive coverage.
- Spot Cleaning: Focuses on a specific dirty area.
- Edge Cleaning: Cleans along walls and furniture edges.
- Scheduled Cleaning: Set specific times for the robot to clean automatically.
Mapping and Navigation
The robot uses 360° laser radar and SLAM algorithm to create real-time maps of your home. This allows for efficient route planning, obstacle avoidance, and features like:
- Map Partition: Divide your home into different areas and customize cleaning order.
- Virtual Blocker: Define areas the robot should avoid (e.g., children's play areas).
- Breakpoint Continuous Cleaning: If the battery runs low during a cycle, the robot returns to the charging station and resumes cleaning from where it left off once recharged.
Illustrates map partition and customization features like virtual blockers. 
Diagram showing the robot returning to its charging station and resuming cleaning.
Maintenance
Regular maintenance ensures your Liectroux ZK901 operates efficiently.
Dustbin and Filter Cleaning
- Press the dustbin release button and remove the dustbin.
- Empty the dustbin contents into a trash can.
- Remove the primary filter and HEPA filter. Tap them gently to remove dust. Rinse the primary filter and dustbin with water if necessary, but ensure they are completely dry before reinstallation. Do not wash the HEPA filter with water.
- Reinstall the filters and dustbin.
Main Brush and Side Brush Cleaning
- Remove the main brush cover and lift out the V-shaped roller brush. Use the cleaning tool (if provided) to cut and remove any tangled hair or debris.
- Pull off the side brushes. Remove any hair or debris.
- Reinstall all brushes securely.
Sensor and Charging Contact Cleaning
Wipe all sensors (including cliff sensors, anti-collision sensors, and lidar sensor) and charging contacts on both the robot and the charging station with a clean, dry cloth. This prevents cleaning errors and ensures proper charging.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Robot does not turn on | Low battery; Power button not pressed long enough | Charge the robot; Press and hold the power button for 3-5 seconds. |
| Robot cannot charge | Charging contacts are dirty; Charging station not powered; Robot not properly aligned | Clean charging contacts; Ensure charging station is plugged in; Reposition robot on charging station. |
| Robot gets stuck frequently | Too many obstacles; Loose cables/rugs; Low obstacle crossing ability | Clear floor of clutter; Secure loose items; Note 1.5cm obstacle crossing limit. |
| Poor cleaning performance | Dustbin full; Filters clogged; Brushes tangled/worn | Empty dustbin; Clean/replace filters; Clean/replace brushes. |
| Water leakage during mopping | Water tank not properly installed; Robot charging while water tank is attached | Ensure water tank is securely in place; Remove water tank before charging. |
| App connection issues | Incorrect Wi-Fi password; Robot too far from router; App not updated | Verify Wi-Fi credentials; Move robot closer to router; Update app to latest version. |
Specifications
| Feature | Specification |
|---|---|
| Brand Name | Liectroux (WMWMNU) |
| Model Number | ZK901 |
| Power (W) | 40W |
| Voltage (V) | 14.4V |
| Motor Type | Brushless Motor (Japan NIDEC Brushless Fan) |
| Function | Wet And Dry Sweeping |
| Application | Household |
| Power Source | Battery |
| Dust Box Capacity (L) | <0.5 L |
| Suction Power | >2499Pa |
| Maximum Runtime | 121-150 minutes |
| Automatic Dirt Disposal | No |
| Navigation Mode | Lidar + SLAM Dual Location |
| Navigation System | LDS Laser Whose House Planned Navigation |
| Maps Building and Location Algorithm | Driverless Level SLAM Algorithm |
| Carpets Pressurization | Identifies and pressurizes carpets automatically |
| Sensor Quantity | 13 Types, 42 Sets of Sensors |
| Obstacle Crossing Ability | 1.5cm |
| Battery Capacity | 5000mAh LG High Energy Density Li-ion Battery |
| Single Charge Cleaning Time | 150 Minutes (Standard Mode) |
| Single Charge Cleaning Area | 250 square meters (Standard Mode) |
| Water Tank Capacity | 450ml (Micro Electric Control Air Pump) |
| Certifications | EMC, CB, CE, RoHS, GS |
Warranty and Support
The Liectroux ZK901 comes with a 1-year warranty. Free spare parts are provided for after-sales service. For technical support, warranty claims, or inquiries, please contact your retailer or the manufacturer directly.
Contact Information:
WhatsApp: +86 19974103556
Email: 3035818194@qq.com
User Tips
- Pre-Clean Floors: For best results, remove large debris, loose cables, and small objects from the floor before starting a cleaning cycle.
- Regular Maintenance: Clean the dustbin, filters, and brushes after each use, especially if you have pets, to maintain strong suction and prevent tangles.
- Water Tank Usage: Always remove the water tank when the robot is charging or not in use to prevent accidental water leakage. Use only clean water in the tank.
- Map Customization: Utilize the app's map partition and virtual blocker features to optimize cleaning for specific rooms or to protect delicate areas.
- Firmware Updates: Periodically check the app for firmware updates to ensure your robot has the latest features and performance improvements.
