BENINCA TO.GO 2WV

Contents

BENINCA TO.GO 2WV Series Garage Door Remote Control User Manual

Model: TO.GO 2WV, TO.GO 4WV, and compatible models

1. Introduction

This manual provides instructions for the BENINCA TO.GO 2WV series garage door remote control. This remote is designed to operate with BENINCA rolling code systems at a frequency of 433.92MHz. It is available in 2-button and 4-button configurations.

Please read this manual carefully before attempting to set up or use your new remote control.

2. Package Contents

Upon opening the package, you should find the following items:

  • 1 x Remote Control (2-button or 4-button version)
  • 1 x Battery (pre-installed or included separately)
  • 1 x Keychain
  • 1 x English Manual

Video: Unboxing and basic operation of the remote control.

3. Specifications

Feature Detail
Model TO.GO 2WV (and compatible series)
Frequency 433.92MHz
Encoding Method Rolling Code (64-bit)
Buttons 2 or 4
Battery Included
Dimensions (2-button) Approx. 70mm (L) x 40mm (W) x 14mm (T)
Certification CE
Origin Mainland China
2-button remote control from various angles

Image: Views of the 2-button remote control (front, side, and back with battery cover).

2-button remote control with dimensions

Image: Dimensions of the 2-button remote control.

4. Compatibility

This remote control is compatible with the following BENINCA rolling code models (64-bit):

  • Beninca TO GO 2WV
  • Beninca TO GO 4WV
  • BENINCA IO.2WV
  • BENINCA LO.T2WMR
  • BENINCA T2 WV
  • BENINCA T4 WV
  • BENINCA CUPIDO-2
  • BENINCA CUPIDO-4
  • APPLE 4WV / APPLE 2WV

It is compatible with all color variations of these models.

Compatibility chart for BENINCA rolling code remotes

Image: Visual guide to compatible BENINCA rolling code remote models.

5. Important Notes

  • This remote control is NOT applicable to the new yellow button BENINCA TO 2VA 4VA models, which use ARC code.
  • This remote can be programmed directly at the receiver unit of your garage door opener.
  • It is NOT possible to clone an existing remote control to this device. Programming must be done at the receiver.
Incompatibility warning for BENINCA TO.GO 2A (ARC) vs TO.GO 2WV (Rolling Code)

Image: Visual warning distinguishing between incompatible ARC code (TO.GO 2A) and compatible rolling code (TO.GO 2WV) remotes.

6. Setup and Programming

Programming this remote control requires access to your BENINCA garage door opener's receiver unit. The exact steps may vary slightly depending on your specific receiver model. Always refer to your garage door opener's manual for precise programming instructions.

General programming steps for BENINCA rolling code receivers:

  1. Locate the Receiver: The receiver unit is typically located on the garage door opener motor itself, or sometimes in a separate control box near the motor.
  2. Find the Programming Button: Look for a small button on the receiver, often labeled 'PROG', 'MEMO', 'LEARN', or similar. It might be recessed and require a small pointed object (like a paperclip) to press.
  3. Activate Learning Mode: Press and release the programming button on the receiver. An LED indicator on the receiver should light up or flash, indicating it is in learning mode. This mode usually lasts for a few seconds.
  4. Transmit from New Remote: While the receiver is in learning mode, press and hold the desired button on your new BENINCA remote control for 1-2 seconds.
  5. Confirm Programming: The LED on the receiver should flash or change state to confirm successful programming. Release the button on the remote.
  6. Test the Remote: Wait a few seconds for the receiver to exit learning mode, then press the programmed button on your new remote to test its operation.

Important: If you have multiple remotes to program, repeat steps 3-5 for each remote and desired button within the receiver's learning window.

7. Operating Instructions

Once programmed, operating your BENINCA remote control is straightforward:

  • Opening/Closing: Press the programmed button on the remote control. The garage door will open or close.
  • Stopping Movement: Press the programmed button again while the door is in motion to stop it.
  • LED Indicator: When a button is pressed, the LED indicator on the remote will light up, confirming that a signal is being transmitted.
Hand pressing a button on the 4-button remote control

Image: Demonstrating pressing a button on the 4-button remote.

Hand pressing a button on the 2-button remote control

Image: Demonstrating pressing a button on the 2-button remote.

8. Maintenance

Battery Replacement

If the remote control's LED indicator does not light up or appears dim when a button is pressed, the battery may need to be replaced. The remote uses a standard coin cell battery (e.g., CR2032, specific type may vary, check your remote's battery compartment).

  1. Open the Remote: Locate the small notch or opening at the bottom of the remote. Use a small flat-head screwdriver or a coin to carefully pry open the remote casing.
  2. Remove Old Battery: Carefully remove the old battery from its compartment. Note the orientation (+/-).
  3. Insert New Battery: Insert a new battery with the correct polarity.
  4. Close the Remote: Snap the remote casing back together securely.
  5. Test: Test the remote's function with your garage door opener.

Refer to the unboxing video in Section 2 for a visual guide on accessing the battery compartment.

9. Troubleshooting

Problem Possible Cause Solution
Remote does not work after programming. Incorrect programming steps, receiver not in learning mode, or remote not compatible. Review Section 5 (Important Notes) and Section 6 (Setup and Programming). Ensure your remote is compatible and re-attempt programming carefully. Consult your opener's manual.
Remote LED does not light up when button is pressed. Dead or low battery. Replace the battery as described in Section 8.
Remote works intermittently or has reduced range. Low battery, interference, or remote/receiver obstruction. Replace battery. Check for sources of interference (e.g., other wireless devices). Ensure clear line of sight between remote and receiver.
Cannot clone an existing remote. This remote uses rolling code and cannot be cloned. This is expected behavior. Programming must be done directly at the receiver as per Section 6.

10. User Tips

  • Always keep your garage door opener's manual handy for specific programming details, as procedures can vary by model.
  • If you have multiple BENINCA rolling code openers, you can often program different buttons on a single remote to control different doors.
  • Store your remote in a safe place, away from extreme temperatures or direct sunlight, to prolong battery life and device integrity.

11. Warranty and Support

For any issues or questions regarding your BENINCA remote control, please contact the seller or manufacturer's customer support. Keep your purchase receipt as proof of purchase for warranty claims.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.