DIVEDEER LPG Gas Hot Water Heater (6L-18L Series)

Contents

DIVEDEER LPG Gas Hot Water Heater User Manual

Model: LPG Gas Hot Water Heater (6L-18L Series)

Brand: DIVEDEER

1. Introduction

Thank you for choosing the DIVEDEER LPG Gas Hot Water Heater. This tankless water heater is designed to provide instant hot water for various applications, including home use, camping, and outdoor activities. Available in multiple capacities from 6L to 18L, it features a stainless steel water tank, efficient heating, and intelligent temperature control for a comfortable bathing experience. Please read this manual thoroughly before installation and operation to ensure safe and efficient use of your water heater.

DIVEDEER LPG Gas Hot Water Heater with accessories

Image: DIVEDEER LPG Gas Hot Water Heater showing main unit, shower head, hose, and control knobs.

2. Important Safety Information

WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Read the installation, operating, and maintenance instructions thoroughly before installing or servicing this equipment.

  • This appliance must be installed by a qualified person in accordance with all local codes and regulations.
  • Ensure adequate ventilation when operating the water heater.
  • Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
  • Always check for gas leaks after installation or maintenance.
  • The water heater requires 2pcs 1.5V D-Type Batteries for ignition (not included). Ensure batteries are correctly installed.
  • Before first use, the water heater needs to be vented to remove any air residue in the pipeline. Failure to do so may lead to poor water flow or damage to the machine.
  • Do not obstruct the exhaust flue.

3. Product Overview

The DIVEDEER LPG Gas Hot Water Heater features intuitive controls and robust construction for reliable performance.

3.1 Components and Controls

Function and Battery Installation Schematic

Image: Detailed view of the water heater's bottom panel showing controls and battery compartment.

  1. Fire Row Control: Adjusts the intensity of the gas flame.
  2. Gas Flame Control: Regulates the gas supply to the burner.
  3. Water Size Control: Adjusts the water flow rate.
  4. Digital Display: Shows real-time water temperature.
  5. Ignition Switch: Initiates the ignition process.
  6. Indicator Light: Provides status feedback.
  7. Monitor: Internal sensor for operation.
  8. Battery Pack: Compartment for 2pcs 1.5V D-Type Batteries (Positive and Negative terminals indicated).

3.2 Key Features

  • Stainless Steel Water Tank: Pure copper heat exchanger for rapid heating and energy saving.
  • D-Type Batteries: Powers the ignition system.
  • Gas Emission Tube: For safe exhaust of combustion gases.
  • Back Screw Holes: For secure wall mounting.
  • CPU Intelligent Temperature Control: Precise temperature regulation for consistent hot water.
  • Segmented Fire Row Combustion: Automatic switching between high and low fire for stable temperature even with varying water consumption.
  • Low Voltage Start: Operates effectively even in areas with lower water pressure or in high-rise buildings.
  • Multi-Safety Protection: Includes instant heat, real-time temperature display, low voltage startup, and safe exhaust.
Premium and Exquisite Details of the water heater

Image: Close-up details of the water heater, including the stainless steel water tank, D-type battery compartment, gas emission tube, and back screw holes.

4. Specifications

Feature Detail
Hot Water Output 6L/min (1.6 GPM), 8 L/min (2.1 GPM), 10 L/min (2.7 GPM), 12 L/min (3.2 GPM), 16 L/min (4.3 GPM), 18 L/min (4.8 GPM)
Heater Output Power 12KW, 16KW, 20KW, 24KW, 32KW, 36KW (corresponding to capacity)
Gas Type LPG (Liquid Petroleum Gas)
Gas Pressure 2800 Pa
Water Temperature Range 50 °F - 140 °F (10℃ - 60℃)
Water Connection G1/2"
Rubber Gas Hose Diameter φ 0.79"
Suitable Water Pressure 0.02 MPA - 0.8 MPA
Starting Pressure 0.015 MPA
Exhaust Way Open & Force Flue Exhaust Type
Discharge Ways Flue Automatic Gas Discharge
Ignition 2pcs 1.5V D-Type Batteries (not included)
Housing Material Stainless steel

4.1 Package Contents

  • 1 x DIVEDEER LPG Hot Water Heater (selected capacity)
  • 1 x Shower Head
  • 1 x Install Accessories Kit
  • 1 x English User Manual

5. Setup and Installation

Proper installation is critical for the safe and efficient operation of your water heater. If you are unsure about any steps, please consult a qualified professional.

5.1 Pre-Installation Checks

  • Ensure you have all necessary accessories and tools.
  • Verify the gas type (LPG) and pressure match the water heater's specifications.
  • Confirm the installation location provides adequate ventilation and meets local regulations for gas appliances.

5.2 Battery Installation

The water heater requires 2pcs 1.5V D-Type Batteries for ignition. These are not included in the package.

  1. Locate the battery compartment on the bottom panel of the water heater (refer to "Function and Battery Installation Schematic" image).
  2. Open the battery cover.
  3. Insert two 1.5V D-Type batteries, ensuring correct polarity (Positive and Negative terminals are marked).
  4. Close the battery cover securely.

5.3 Water and Gas Connections

Firmly connect the inlet and outlet water pipes to the device interface. Ensure the water flow is unimpeded.

  • Connect the cold water inlet pipe to the designated inlet port.
  • Connect the hot water outlet pipe to the designated outlet port.
  • Connect the LPG gas supply hose (φ 0.79") to the gas inlet. Ensure all connections are tight and leak-free.

5.4 Exhaust Pipe Installation

The exhaust pipe must be installed correctly to safely vent combustion gases. The total length of the exhaust pipe should be within 3 meters, with a maximum of 3 bends.

Installation Diagram for exhaust pipe

Image: Diagrams illustrating how to install the exhaust pipe to the side or rear of the unit, including components like the exhaust straight tube and elbow.

5.5 Initial Venting (Crucial First Step)

Before starting the water heater for the first time, it is essential to vent any air residue from the water pipelines. Failure to do so can lead to poor water flow or damage to the unit.

  1. Once water connections are secure, slowly open the cold water supply valve to the water heater.
  2. Open a hot water tap in your home (e.g., a shower or sink).
  3. Allow water to flow through the system until all air is purged and a steady stream of water comes out of the hot water tap.
  4. Close the hot water tap.

6. Operating Instructions

Once installed and vented, your DIVEDEER water heater is ready for operation.

6.1 Starting the Water Heater

  1. Ensure the gas supply valve is open.
  2. Open a hot water tap. The water heater will automatically detect water flow and initiate the ignition sequence.
  3. The digital display will show the real-time water temperature.
  4. If the water heater does not ignite, check the gas supply, water flow, and battery status.

6.2 Adjusting Water Temperature and Flow

Use the control knobs on the front panel to adjust your desired water temperature and flow rate.

  • Water Size Control: Adjusts the volume of water flowing through the heater. A lower flow rate generally results in hotter water (given constant gas input), and a higher flow rate results in cooler water.
  • Gas Flame Control / Fire Row Control: Adjusts the gas supply to the burner, directly impacting the heat output. Increase for hotter water, decrease for cooler water.
Mechanical simple and convenient adjustment knob

Image: Water heater showing mechanical adjustment knobs for easy temperature and flow control.

The intelligent temperature control system maintains a constant water temperature, even when water consumption fluctuates, ensuring a comfortable bathing experience.

Constant water temperature with ±0.5℃ difference

Image: Illustrates the water heater's ability to maintain a constant water temperature with minimal fluctuation.

7. Maintenance

Regular maintenance ensures the longevity and efficient operation of your water heater.

  • Battery Replacement: Replace the D-Type batteries when the ignition becomes weak or fails.
  • Cleaning: Periodically clean the exterior of the unit with a soft, damp cloth. Do not use abrasive cleaners.
  • Exhaust Flue Inspection: Regularly check the exhaust flue for any obstructions or damage. Ensure it is clear and securely connected.
  • Water Inlet Filter: Inspect and clean the water inlet filter periodically to prevent blockages from sediment.
  • Professional Inspection: It is recommended to have the water heater inspected by a qualified technician annually, especially for gas connections and combustion efficiency.

8. Troubleshooting

If you encounter issues with your water heater, refer to the following common problems and solutions:

Problem Possible Cause Solution
No hot water / Water heater not igniting
  • No gas supply
  • Low water pressure
  • Dead or incorrectly installed batteries
  • Air in water pipes (first use)
  • Ignition sensor fault
  • Check gas cylinder/supply.
  • Ensure water supply is fully open and pressure is adequate (min 0.015 MPA).
  • Replace batteries, ensuring correct polarity.
  • Perform initial venting procedure (Section 5.5).
  • Contact customer support if problem persists.
Water not hot enough
  • Insufficient gas flow
  • Too high water flow rate
  • Cold incoming water temperature
  • Increase Gas Flame Control.
  • Decrease Water Size Control.
  • Adjust controls to find optimal balance for desired temperature.
Water heater cycles on/off rapidly
  • Insufficient water flow
  • Overheating protection activated
  • Ensure adequate water pressure and flow.
  • Check for kinks in hoses or clogged filters.
  • Reduce gas input if water is too hot.
Gas smell
  • Gas leak
  • Immediately turn off gas supply.
  • Ventilate the area.
  • Do NOT operate any electrical switches or open flames.
  • Contact a qualified gas technician immediately.

9. User Tips

  • For optimal performance and consistent hot water, ensure your water pressure is within the recommended range (0.02 MPA - 0.8 MPA).
  • When using for camping or outdoor showers, ensure the unit is placed on a stable, level surface and protected from direct rain.
  • Always have spare D-Type batteries on hand, especially for outdoor use, as they are essential for ignition.
  • If you experience fluctuating water temperatures, try slightly reducing the water flow rate to allow the heater more time to heat the water.

10. Warranty and Support

For any questions, technical assistance, or warranty claims, please contact the seller directly. Provide your order number and a detailed description of the issue. The seller's customer service email is cutelin9@qq.com.

Please note that the product comes with a 2-year warranty, as indicated by the seller.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.