1. Introduction
This manual provides essential information for the safe and efficient operation of your SUMRY Hybrid Solar Inverter 10.2KW MPS V-MAX Series. This inverter is designed to provide reliable, clean, and quiet AC energy for both on-grid and off-grid living, featuring dual MPPT solar charge controllers, dual PV inputs, and dual AC outputs. Please read this manual thoroughly before installation and use.

Figure 1: SUMRY Hybrid Solar Inverter 10.2KW MPS V-MAX Series. Key specifications include 10.2KW Max. PV Input Power, 140A Max. AC Charging Current, 90-450VDC MPPT Voltage Range, and 50Hz/60Hz Frequency Range.
2. Key Features
- Pure sine wave solar inverter (on/off Grid)
- Output power factor 1.0
- Inverter can run without battery
- Built-in 160A MPPT solar charger (for 10.2kw model)
- High PV input voltage range (90-500VDC)
- Dual communication ports for Battery communication (RS485) and Wifi communication (RS232)
- Dual output and Dual PV input
- Touch button interface
- Built-in Lithium battery automatic activation
- Built-in anti-dust kit for harsh environments
- Smart battery charge design to optimize battery life
- WIFI & GPRS available for iOS and Android monitoring
- One-key restoration to factory settings

Figure 2: Overview of the inverter's main features, highlighting its pure sine wave output, battery-less operation, and smart charging capabilities.
3. Setup and Installation
The SUMRY Hybrid Solar Inverter requires assembly and professional installation. Ensure all connections are secure and follow local electrical codes.
3.1 Basic System Architecture
The inverter integrates solar power, generator/utility input, battery storage, and AC output for home appliances. Solar panels are recommended to be connected in series.

Figure 3: System diagram illustrating connections for solar panels, generator/utility, battery, inverter, and home appliances. Max PV Input Power is 10200W, Max Solar Charging Current is 160A, and Max AC Charging Current is 140A.
3.2 Physical Dimensions and Overview
The inverter has a compact design for easy integration into your solar power system.

Figure 4: Dimensions of the inverter (D*W*H: 530*420*160mm) and location of the touch button interface.

Figure 5: Rear panel overview showing connection points: 1 AC input, 2 Main output, 3 Second output, 4 PV1 and PV2 input, 5 Battery input, 6 WIFI communication RS-232 Port, 7 Battery communication/RS-485 port.
3.3 Battery Connection
The inverter is compatible with various battery types including Flooded, Gel, Lithium-iron phosphate, Lithium-ion, and AGM/Sealed batteries. It also supports user-customized battery settings. Ensure correct polarity when connecting battery packs.

Figure 6: Compatible battery types and a basic chart for connecting multiple 12V battery packs to the inverter.
3.4 Communication Ports
The inverter features dual communication ports for battery management systems (BMS) and WiFi connectivity.

Figure 7: Close-up of the RS232 (WiFi), RS485 (BMS) communication ports and the Main Out and Second Out AC outputs.
4. Operation
4.1 LCD Display and Function Buttons
The inverter features an LCD display and touch buttons for easy configuration and monitoring.

Figure 8: Inverter display and controls. Function buttons include ESC (exit setting mode), UP (previous selection), DOWN (next selection), and ENTER (confirm selection/enter setting mode).
4.2 LED Indicators
The LED indicators provide quick status updates:
| LED Indicator | Messages |
|---|---|
| INV/AC (Green) | Solid On: Output is powered by utility in Line mode. Flashing: Output is powered by battery or PV in battery mode. |
| CHG (Green) | Solid On: Battery is fully charged. Flashing: Battery is charging. |
| FAULT (Red) | Solid On: Fault occurs in the inverter. Flashing: Warning condition occurs in the inverter. |
4.3 Remote Monitoring
Monitor and control your inverter via the SmartESS App, available for download on app stores (iOS and Android). An optional WiFi dongle may be required for connectivity.

Figure 9: The SmartESS App allows remote monitoring and control of your solar inverter system.
5. Maintenance
- Regular Inspection: Periodically check all connections for tightness and signs of wear or corrosion.
- Cleaning: Keep the inverter's ventilation openings clear of dust and debris. The built-in anti-dust kit helps in harsh environments, but regular cleaning is still recommended.
- Battery Care: The smart battery charge design optimizes battery life. Ensure your battery type is correctly configured in the inverter settings for optimal charging.
- Firmware Updates: Check the manufacturer's website or the SmartESS app for any available firmware updates to ensure optimal performance and new features.
6. Troubleshooting
The inverter is equipped with comprehensive protection features to ensure safe operation. Refer to the LED indicators (Section 4.2) for initial fault diagnosis.
6.1 Comprehensive Protections

Figure 10: The inverter includes protections against Overload, Overheating, High/Low Voltage, Battery issues, Short Circuit, Overcurrent, Anti-Reverse polarity, and Power Failure.
6.2 Common Issues and Solutions
- Inverter not turning on: Check AC input, battery connections, and PV input voltage. Ensure the main power switch is on.
- No output power: Verify AC output connections. Check for any fault indicators on the LCD or LEDs.
- Battery not charging: Confirm PV input voltage is within the MPPT range (90-450VDC). Check solar panel connections and battery health.
- Warning/Fault LED: Refer to the LED Indicator table (Section 4.2) for specific messages. If a fault persists, try a one-key restoration to factory settings (refer to the full manual for detailed steps).
- App connectivity issues: Ensure the optional WiFi dongle is correctly installed and configured. Check your home WiFi network and app settings.
7. Specifications
Below are the detailed specifications for the SUMRY MPS V-MAX Series 10.2KW model.
| Category | Parameter | MPS V-MAX SERIES-10.2KW |
|---|---|---|
| General | Phase | 1-phase |
| Maximum PV Input Power | 10200W | |
| Rated Output Power | 10200W/10200VA | |
| Maximum Solar Charging Current | 160A | |
| Grid-Tie Operation (PV Input DC) | Nominal DC Voltage/Maximum DC Voltage | 360VDC/500VDC |
| Start-up Voltage / Initial Feeding Voltage | 90VDC/120VDC | |
| MPPT Voltage Range | 90-450VDC | |
| Maximum Input Current | 2/18A | |
| Power Factor | >0.99 | |
| Grid Output (AC) | Nominal Output Voltage | 220/230/240VAC |
| Output Voltage Range | 195~253VAC | |
| Nominal Output Current | 44.3A | |
| Efficiency | Maximum Conversion Efficiency (DC/AC) | 98% |
| Efficiency (DC to AC) | 94% | |
| Two Load Output Power | Full Load | 10200W |
| Maximum Main Load | 10200W | |
| Maximum Second Load (battery mode) | 3400W | |
| Off-Grid Operation (AC Input) | AC Start-up Voltage / Auto Restart Voltage | 120-140VAC/180VAC |
| Acceptable Input Voltage Range | 90-280VAC or 170-280VAC | |
| Frequency Range | 59~61±1HZ | |
| Maximum AC Input Current | 60A | |
| Battery & Charger | Nominal DC Voltage | 48VDC |
| Maximum AC Charging Current | 140A | |
| Physical | Dimension (D*W*H) | 530*390*130mm |
| Net Weight | 14.7 kgs | |
| Gross Weight | 16.2 kgs | |
| Installation Method | Assembly | |
| Environment | Humidity | 5% to 95% Relative Humidity (Non-condensing) |
| Operating Temperature | -10°C~50°C | |
| Interface | Communication Port | RS232/RS485/WIFI/GPRS/Lithium Battery |
| Standard | Compliance Safety | CE |
Note: Specifications are subject to change without prior notice. Always refer to the product label for the most accurate information.
8. User Tips
- Battery-less Operation: This inverter can operate without a battery, making it flexible for various solar setups. However, for continuous power supply during outages or at night, a compatible battery bank is essential.
- Remote Monitoring: Utilize the SmartESS app for real-time monitoring of your system's performance, battery status, and energy flow. This can help in optimizing energy usage and detecting potential issues early.
- Dual Output Advantage: The dual AC output feature can be convenient for separating critical loads from non-critical ones, or for powering different sections of a home or office.
- High PV Input Range: The wide PV input voltage range (90-500VDC) offers flexibility in stringing your solar panels, potentially reducing the need for complex wiring configurations.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your original point of purchase or the SUMRY customer service directly. Keep your purchase receipt and product serial number handy for faster service.