Estardyn TS0702H Control

Contents

Estardyn DC 12V PWM Fan Speed Controller Instruction Manual

Model: TS0702H Control

Introduction

The Estardyn DC 12V PWM Fan Speed Controller is a compact and efficient module designed to regulate the speed of 2-3 wire computer fans based on temperature. This device helps to reduce noise, extend fan life, and conserve energy by preventing fans from running at full speed unnecessarily. It features both manual and automatic temperature control modes, making it suitable for various applications including PC CPU coolers, industrial control systems, and outdoor chassis.

Two Estardyn DC 12V PWM Fan Speed Controllers with connecting cables.

Image: Two Estardyn DC 12V PWM Fan Speed Controllers with connecting cables.

Package Contents

  • 2x Estardyn DC 12V PWM Fan Speed Controller Modules
  • Connecting wires (typically includes a 3-pin fan cable and an NTC thermal probe cable)
Estardyn DC 12V PWM Fan Speed Controller with included 2-pin and 3-pin cables.

Image: Estardyn DC 12V PWM Fan Speed Controller with included 2-pin and 3-pin cables.

Specifications

FeatureSpecification
Working VoltageDC 12V
Fan Current0.8A (MAX)
Output Power10W (MAX)
Dissipation Power10mA
Operating Temperature-20°C to +60°C
Temperature ProbeNTC 10K B=3950 1%
Probe Length50cm
Module Size49mm x 18mm x 10mm
ApplicationComputer (CPU Cooler), Industrial Control
Fan Compatibility2-wire or 3-wire fans (does not measure fan speed)
Package TypeSMD

Product Overview

The controller module features clearly labeled interfaces for power input, fan connection, and the NTC thermal probe. A setting key allows for mode adjustments, and an LED indicator provides visual feedback on the current speed or setting mode.

Detailed diagram of the Estardyn PWM Fan Speed Controller showing power input, fan output, NTC probe interface, speed indicator, and setting key.

Image: Detailed diagram of the Estardyn PWM Fan Speed Controller showing power input, fan output, NTC probe interface, speed indicator, and setting key.

  • 12V DC Power Input: Connects to a 12V DC power source (Red: +, Black: -).
  • FAN Output (VO+, VO-): Connects to the fan. VO+ is positive, VO- is negative.
  • NTC Thermal Probe Interface: Connects the included temperature sensor.
  • Setting Key: Used to adjust fan speed and configure operating modes.
  • Speed Indicator: LED lights indicate current fan speed or setting mode.

Note: The controller processes speed signals (Sin input, Sout output) but does not measure the actual fan speed. It is compatible with 2-wire and 3-wire fans.

Back view of the Estardyn DC 12V PWM Fan Speed Controller showing FAN, NTC, and DC12V connections.

Image: Back view of the Estardyn DC 12V PWM Fan Speed Controller showing FAN, NTC, and DC12V connections.

Setup Instructions

Carefully follow these steps for proper installation and connection:

1. Wiring Diagram

Wiring diagram for the Estardyn PWM Fan Speed Controller, showing connections for 12V DC power, fan, and NTC thermal probe.

Image: Wiring diagram for the Estardyn PWM Fan Speed Controller.

  1. Power Connection: Connect the 12V DC power supply to the designated input terminals on the module. Ensure correct polarity (Red wire to +, Black wire to -).
  2. Fan Connection: Connect your 2-wire or 3-wire fan to the FAN output terminals (VO+ and VO-). VO+ is for the positive fan lead, VO- for the negative.
  3. NTC Thermal Probe: Connect the NTC thermal probe to its dedicated interface. Position the probe in the area where temperature monitoring is desired (e.g., near the CPU heatsink for a CPU cooler fan).

Ensure all connections are secure before applying power.

Operating Instructions

The controller offers both manual and automatic temperature-controlled fan speed regulation.

Manual Control

During normal operation, simply click the setting button to increase the fan speed. Release the button to save the current speed. You can adjust the fan speed from 0% to 100% in increments.

Automatic Temperature Control Settings

The fan controller can be configured for automatic speed adjustment based on temperature. The temperature range for control is -20°C to +60°C.

To enter the setting mode:

  1. Press and hold the setting button for 3 seconds. The speed indicator LED will begin to flash, indicating you are in setting mode.
  2. Click the button to cycle through the different setting parameters. Each click changes the value.
  3. After making your desired adjustments, press and hold the button for 3 seconds again to save the settings and exit. Alternatively, if no button is pressed for 20 seconds, the settings will be automatically saved, and the module will exit setting mode.

Setting Parameters:

  • Mode 1 (Slow Flashing): Initial Speed Setting
    Sets the minimum fan speed when the temperature is below the acceleration temperature.
  • Mode 2 (Fast Flashing): Acceleration Temperature Setting
    Sets the temperature at which the fan begins to increase speed.
  • Mode 3 (Slow Flashing): Acceleration Width Setting
    Defines the temperature range over which the fan speed increases from the initial speed to full speed.
  • Mode 4 (Fast Flashing): Fan Shutdown Strategy Setting
    Determines whether the fan stops completely when the temperature falls below the acceleration temperature.

Examples for Fan Shutdown Strategy Setting:

  • Acceleration Temperature 30°C, Acceleration Width 5°C: Fan starts accelerating at 30°C and reaches full speed at 35°C.
  • Acceleration Temperature 30°C, Acceleration Width 0°C: Fan runs at full speed when the temperature reaches 30°C.
  • Acceleration Temperature 30°C, Acceleration Width 10°C: Fan starts accelerating at 30°C and reaches full speed at 40°C.
  • Acceleration Temperature 30°C, Acceleration Width -5°C: Fan starts accelerating at 25°C and reaches full speed at 30°C.
  • Acceleration Temperature 30°C, Acceleration Width -10°C: Fan starts accelerating at 20°C and reaches full speed at 30°C.

If the fan shutdown strategy is enabled, the fan will stop when the temperature is below the acceleration temperature. If disabled, the fan will run at minimum speed when the temperature is below the acceleration temperature.

Maintenance

  • Cleaning: Periodically clean the module and fan to prevent dust buildup, which can affect performance and temperature readings. Use a soft, dry cloth.
  • Connection Check: Regularly inspect all wiring connections to ensure they are secure and free from damage.
  • Probe Placement: Ensure the NTC thermal probe remains securely positioned for accurate temperature sensing.

Troubleshooting

ProblemPossible CauseSolution
Fan not spinning or incorrect speedIncorrect wiring, insufficient power, fan type incompatibility, incorrect settings.Verify 12V DC power input and fan connections. Ensure fan is 2-wire or 3-wire. Check operating mode settings.
Temperature control not workingNTC probe not connected or faulty, probe improperly placed, incorrect temperature settings.Ensure NTC probe is securely connected and positioned correctly. Re-enter setting mode to verify acceleration temperature and width.
Fan runs at full speed constantlyTemperature consistently above acceleration threshold, acceleration width set to 0, or manual control set to 100%.Check NTC probe reading. Adjust acceleration temperature and width. Ensure manual control is not overriding automatic settings.
Fan stops unexpectedlyFan shutdown strategy enabled and temperature below threshold, power interruption.Review Fan Shutdown Strategy setting. Check power supply stability.

User Tips

  • Probe Placement is Key: For optimal temperature control, place the NTC thermal probe as close as possible to the heat source you wish to monitor (e.g., CPU heatsink fins).
  • Test Settings: After adjusting any settings, observe the fan's behavior for a short period to ensure it operates as expected under varying temperature conditions.
  • Fan Compatibility: Remember this controller is designed for 2-wire and 3-wire fans. While it controls speed, it does not provide fan speed feedback.

Warranty and Support

For warranty information or technical support, please refer to the seller's policies or contact the Estardyn customer service directly. Keep your purchase receipt for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.