JIKONG BD6A20S15P-V19

Contents

JIKONG Smart BMS Instruction Manual

Model: BD6A20S15P-V19 Series

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your JIKONG Smart Battery Management System (BMS). The JIKONG Smart BMS is designed for various battery chemistries including LiFePo4, Li-Ion, and LTO, offering active balancing and comprehensive protection features for battery packs ranging from 8S to 24S configurations.

The Smart BMS features Bluetooth and RS485 communication for real-time monitoring and parameter adjustment via a mobile application, ensuring optimal performance and longevity of your battery system.

JIKONG Smart BMS product overview with key features like 8S-24S, 0.6A-2A balancing, 80A-150A charge/discharge, BT/RS485 function, and compatibility with LiFePo4, Li-ion, LTO batteries.

Figure 1: JIKONG Smart BMS Overview

2. Specifications

FeatureSpecification
Brand Namejikong
ModelJKBMS BD6A20S15P-V19 (and variants like JK-B1A20S15P, JK-BD6A24S15P, JK-B1A24S15P, JK-B2A24S15P)
TypeLIFEPO4 Battery BMS, Active Balanced BMS
Handware or SmartSMART BMS
Battery Type CompatibilityLi-ion/LiFePo4/LTO
Battery Strings7S~24S
Charge/Discharge Current150A
Charging Current150A
Balance Current0.6A~2A
Balance FunctionActive Balance
Charge and Discharge PortCommon Port BMS
FunctionsOvercharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection, BT/RS485
Temperature SensorYES
Usage ScenarioPower BMS, 3C Digital BMS
CertificationCE, FCC, RoHS
Operating Temperature Range-30°C to 90°C (Normal discharge)

3. Package Contents

Upon opening the package, please verify that all components are present and undamaged:

  • JIKONG Smart BMS (with built-in Bluetooth)
  • Temperature Sensor (40cm)
  • Balance Wires (75cm)
  • Active Switch (15cm)
  • Heating Cable (Only included with BMS models featuring the Heat Function)
  • User Manual (this document)
Package contents of JIKONG Smart BMS including the BMS unit, temperature sensor, balance wires, active switch, and user manual.

Figure 2: JIKONG Smart BMS Package Contents

4. Installation and Wiring

Important Safety Note: Incorrect wiring can damage the BMS, battery pack, or pose a safety risk. Ensure all connections are correct before applying power. It is recommended to have this process performed by a qualified professional.

4.1 Component Identification

Exploded view of JIKONG Smart BMS showing cooling aluminum alloy upper cover, Mosfet, cable interface, silicone output wire, and cooling aluminum alloy lower cover.

Figure 3: BMS Exploded View and Components

Detailed view of BMS ports including NTC (temperature sensor), CAN/RS485, GPS, Display, and Heating Cable connections. Shows GND_L for CAN/RS485 and LCD as default, Heat Function and CAN/RS485 as customizable.

Figure 4: BMS Port Connections

4.2 Wiring Diagram

Connect the protection board and battery pack according to the following wiring diagram. Ensure that the last power cord (B+) is connected to the main positive pole of the battery pack. The total voltage of the battery pack must be greater than 20V (for default BMS) or 10V (for 4S BMS) before startup.

JIKONG Smart BMS wire diagram showing connections for 8S-24S battery packs. Illustrates B-, B+, and individual cell connections (B1, B2, B3, etc.) and heating pad connection.

Figure 5: JIKONG BMS Wiring Diagram (General)

The BMS is compatible with battery packs of different string numbers. The wiring will adapt to the number of cells in your pack (e.g., 8, 10, 12 strings).

Video 1: JIKONG Active Balance BMS demonstration showing cell voltage balancing and compatibility with various string numbers.

Heating Function Wiring (if applicable): The green 5PIN cable of the heating cable needs to be linked to the heating pad. The black and red cables are linked to the smart charger. The smart charger, linked to the BMS, detects battery temperature and automatically monitors the charging status for heating.

  • Heating power depends on battery voltage (U) and heating film resistance (R). Power = U*U/R.
  • Heating current I = U/R.
  • Maximum heating current for the board design is 3A.
  • Maximum heating power is 200W (100W for B2A8S20P model).

5. Operation

5.1 BMS Activation

After completing the wiring, activate the BMS using the display activation button or an additional switch.

5.2 Mobile Application (App)

The JIKONG Smart BMS can be monitored and controlled via a mobile application. Ensure your mobile device's Bluetooth and GPS are turned on.

  • Download for iOS: Search "JIKONG BMS" in the App Store.
  • Download for Android: Search "JK BMS" in the Google Play Store.

Connecting to the App:

  1. Open the JIKONG BMS application.
  2. Click on the top left corner of the app to search for devices.
  3. Select your device name to connect. The default password is 1234.
Screenshot of the JIKONG Smart BT APP interface showing real-time battery data monitoring, parameter modification support, and BMS balance switch control, compatible with Android and iOS.

Figure 6: Smart BT APP Interface

Mobile APP page display showing various screens for active balancing, basic settings, advanced settings, password entry, and cell resistance monitoring for Li-ion, LiFePo4, and LTO batteries.

Figure 7: Mobile App Page Display for Active Balancing and Settings

5.3 Initial Parameter Settings

For the first startup, parameters need to be set. Setting parameters requires a password; the default parameter setting password is 123456. Simply set the number of units (battery strings) and battery type (Li-ion, LiFePo4, or LTO).

After setting the parameters, return to the real-time status page. Check the battery status to ensure no error messages are prompted and normal operation is indicated. Blue indicates the highest cell voltage, and red indicates the lowest cell voltage.

5.4 Smart Energy Working Modes

The BMS supports various working modes to optimize battery life and performance:

  • Storage Mode: In transportation, offline, or wireless transmission off mode, the BMS enters storage mode, which does not consume battery pack current.
  • Normal Working Mode: When the charger is inserted in storage mode and off mode, the BMS immediately returns to normal working mode, and all protection, equalization, and communication functions return to normal.
  • Shutdown: To prevent the BMS from wasting power for a long time and damaging the battery pack, the BMS has an automatic shutdown voltage. It automatically shuts down when a cell falls below the shutdown voltage.
  • Standby Mode: When the battery pack is in a static state (no charge and discharge current and no equilibrium current), the BMS automatically enters standby state after a set time (1-30 days, configurable).
Diagram illustrating Smart energy working mode switching: Storage Mode, Normal Working Mode, Shutdown, and Standby Mode, with transitions based on charging activation, long time unused, and below shutdown voltage.

Figure 8: Smart Energy Working Mode Switching

6. Safety Features

The JIKONG Smart BMS incorporates six major security protections to ensure the safe operation and longevity of your battery pack:

  • Overcharge Protection: Prevents over-charging, which can affect battery life.
  • Over Discharge Protection: Prevents the battery from running out completely.
  • Overcurrent Protection: Prevents the current from exceeding the battery's safe range.
  • Short Circuit Protection: Provides automatic protection when a short circuit occurs.
  • All-in Protection: Prevents cable drop or poor contact.
  • Over Temperature Protection: Prevents the battery from overheating.
Diagram illustrating six security protections: Overcharge Protection, Short Circuit Protection, Over Discharge Protection, Overcurrent Protection, ALL-IN Protection (cable drop/poor contact), and Over Temperature Protection.

Figure 9: Six Security Protections

The BMS is designed to be cold and high temperature resistant, allowing normal discharge at operating temperatures from -30°C to 90°C.

Image showing the JIKONG Smart BMS operating in extreme temperatures, indicating normal discharge is possible from -30°C to +90°C.

Figure 10: Cold and High Temperature Resistance

7. Troubleshooting

This section addresses common issues you might encounter with your JIKONG Smart BMS.

7.1 BMS Does Not Turn On

  • Ensure that the last "B+" line of the cable has been correctly connected to the positive pole of the battery.
  • Start up after charging and ensure that the charger voltage is greater than 4V of the battery pack voltage.
  • Check whether the charger has voltage output.

7.2 Inaccurate Voltage Readings

  • Measure the actual total voltage of the battery pack with a multimeter.
  • Enter this actual total voltage into the "voltage calibration" field on the parameter setting page within the app.

7.3 Inaccurate Current Readings

  • The B- and P- terminals of the protection board use two 7AWG wires. Both must be connected in parallel; otherwise, it will lead to current errors.
  • Measure the actual current of the battery pack with a clamp meter.
  • Enter this actual current into the "current calibration" field on the parameter setting page. The larger the actual current, the higher the calibration accuracy.

7.4 Inaccurate Capacity Readings

  • An initial capacity estimated according to the monomer voltage when the protection board is powered on for the first time may be inaccurate.
  • For accurate calibration, fully discharge the battery pack to its cut-off voltage, then fully charge it without interruption. The capacity will be calibrated during this process.

7.5 Inconsistent String Number

  • Check whether the "unit quantity" in the parameter settings within the app is set correctly to match your battery pack's string count.
  • If there is no voltage in two or more strings in the middle of the pack, check whether the acquisition cable has fallen off or is improperly connected.

8. User Tips

  • Always double-check all wiring connections before powering on the BMS to prevent damage.
  • Regularly monitor cell voltages via the app to ensure proper balancing and overall battery health.
  • Keep the BMS firmware updated to benefit from the latest features and improvements.
  • For optimal performance, ensure the BMS is installed in a location with adequate ventilation, especially if using the heating function.

9. Certifications

The JIKONG BMS has obtained the following product certifications, ensuring compliance with international standards for safety and quality:

  • RoHS (Restriction of Hazardous Substances)
  • FCC (Federal Communications Commission)
  • CE (Conformité Européenne)
Image displaying product certifications for JIKONG BMS, including RoHS, FCC, and CE certificates.

Figure 11: Product Certifications

10. Support and Further Information

For additional support, detailed protocols, or the latest information, please refer to the following resources:

Contact your seller or JIKONG customer support for specific warranty details or technical assistance not covered in this manual.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.