STEPPERONLINE PB65-65241800-G18/36/184

Contents

STEPPERONLINE PB65 24V DC Brushed Gear Motor User Manual

Model: PB65-65241800-G18/36/184

Brand: STEPPERONLINE

1. Introduction

This manual provides essential information for the safe and efficient operation of your STEPPERONLINE PB65 24V DC Brushed Gear Motor. This motor features a planetary gearbox, offering high efficiency, increased torque, and quiet operation. It is characterized by excellent sealing and a high level of waterproofing (IP66), along with an insulation class of F 155°C [311°F].

The PB65 series is widely used in applications requiring high precision, low speed, and high torque, such as photovoltaic modules, precision instruments, consumer electronics, and household appliances.

PB65 Brushed 24V DC Gear Motor highlighting features
Figure 1: PB65 Brushed 24V DC Gear Motor with highlighted features: Higher Efficiency, Higher Torque, High-level Waterproof (IP66), Excellent Sealing.

2. Safety Instructions

Please read and understand all safety instructions before installing, operating, or maintaining the motor. Failure to comply may result in injury or damage to the product.

  • Electrical Safety: Ensure the power supply voltage matches the motor's rated voltage (24V DC). Disconnect power before making any electrical connections or performing maintenance.
  • Mechanical Safety: Keep hands, clothing, and tools clear of rotating parts during operation. Ensure the motor is securely mounted to prevent movement or vibration.
  • Temperature: Do not operate the motor outside its specified ambient temperature range (-40°C to 80°C). The motor surface may become hot during operation; avoid direct contact.
  • Environment: The motor has an IP66 rating, indicating protection against dust and powerful water jets. However, avoid submerging the motor or exposing it to corrosive environments unless specifically designed for such conditions.
  • Overload: Do not exceed the rated torque or maximum permissible torque to prevent damage to the motor and gearbox.

3. Package Contents

Upon unpacking, please verify that all items are present and undamaged:

  • 1x STEPPERONLINE PB65 24V DC Brushed Gear Motor (with selected gear ratio)
  • (Additional accessories, if any, would be listed here by the seller)

4. Specifications

The following table details the technical specifications for the PB65 series DC Brushed Gear Motors:

Detailed specifications table for PB65 motor with different gear ratios
Figure 2: Technical Specifications for PB65 Gear Motors.
PB65 Series DC Brushed Gear Motor Specifications
Parameter PB65-65241800-G18 PB65-65241800-G36 PB65-65241800-G184
Motor TypeBrushed DC Motor
Rated Voltage24V
Rated Current≤4.5A
Peak Current≤6.5A
Rated Power66W
Rated Speed Without Gearbox1800±10%RPM
Rated Torque Without Gearbox0.35Nm (49.56oz.in)
Peak Torque Without Gearbox0.52Nm (73.64oz.in)
Rated Speed With Gearbox100±10%RPM50±10%RPM9.8±10%RPM
Rated Torque With Gearbox5Nm (708.06oz.in)10Nm (1416.12oz.in)45Nm (6372.52oz.in)
Maximum Permissible Torque7.5Nm (1062.09oz.in)15Nm (2124.17oz.in)65Nm (9204.76oz.in)
Insulation ClassF 155°C [311°F]
IP RatingIP66
Gearbox TypePlanetary
Gear Ratio18:136:1184:1
Motor SizeΦ65 x 200mmΦ65 x 215mm
Flange Size68 x 68mm
Shaft DiameterΦ15mm
Shaft Length32mm
Shaft TypeKeyway
Keyway Length25mm

5. Setup and Installation

Follow these steps for proper installation of your PB65 gear motor:

5.1 Mechanical Mounting

  • The motor features a 68 x 68mm square flange for mounting.
  • Use the four Ø7mm mounting holes (4-Ø7EQS) to secure the motor to your application.
  • Ensure the mounting surface is flat and rigid to prevent vibration and misalignment.
  • The output shaft has a diameter of Ø15mm and a length of 32mm, with a 5x5x25mm keyway. Ensure your coupling or load mechanism is compatible with these dimensions.
Dimensional drawing of the PB65 motor
Figure 3: Dimensional Drawing of the PB65 Gear Motor. Key dimensions include a motor body diameter of Ø65mm, flange size of 68x68mm, shaft diameter of Ø15mm, shaft length of 32mm, and a 5x5x25mm keyway. The cable length is 0.5m.

5.2 Electrical Connection

The motor is supplied with a 0.5m cable. Connect the motor to a stable 24V DC power supply. The motor typically has two wires for power connection:

  • Black Wire (BLK): Connect to the negative (-) terminal of the 24V DC power supply.
  • White Wire (WHT): Connect to the positive (+) terminal of the 24V DC power supply.
  • Rotation Direction: Reversing the polarity (connecting Black to + and White to -) will reverse the direction of rotation.
  • Ensure all connections are secure and insulated to prevent short circuits.
Angled view of the motor's cable entry Rear view of the motor showing cable entry and breather valve
Figure 4: Cable entry and breather valve on the motor.

6. Operation

Once the motor is mechanically mounted and electrically connected, you can begin operation:

  • Power On: Apply 24V DC power to the motor. The motor should begin to rotate at its rated speed for the selected gear ratio.
  • Speed Control: For variable speed applications, an external DC motor speed controller (PWM controller) can be used. Ensure the controller is rated for the motor's current and voltage requirements.
  • Direction Control: As mentioned in the setup section, reversing the polarity of the DC power supply to the motor leads will reverse its direction of rotation.
  • Monitoring: Observe the motor during initial operation for any unusual noise, vibration, or excessive heat.

7. Maintenance

Regular maintenance helps ensure the longevity and optimal performance of your gear motor:

  • Cleaning: Periodically clean the exterior of the motor to prevent dust and debris buildup, especially around the motor body and shaft area. While IP66 rated, excessive buildup can affect heat dissipation.
  • Connections: Regularly check all electrical connections for tightness and signs of corrosion.
  • Mounting: Verify that the motor remains securely mounted and that all mounting bolts are tight.
  • Breather Valve: The motor is equipped with a breather valve (visible in Figure 4). Ensure it is not obstructed to allow for proper pressure equalization.
  • Lubrication: The planetary gearbox is factory-lubricated and generally does not require user maintenance or re-lubrication under normal operating conditions.

8. Troubleshooting

If you encounter issues with your PB65 gear motor, refer to the following common problems and solutions:

Problem Possible Cause Solution
Motor does not run No power supply; Incorrect wiring; Faulty power supply; Overload condition. Check 24V DC power supply connection; Verify wiring polarity; Test power supply; Reduce load.
Motor runs slowly or with reduced torque Insufficient power supply voltage/current; Excessive load; Motor/gearbox damage. Ensure stable 24V DC supply with adequate current; Reduce load to within rated torque; Contact support if motor/gearbox is suspected to be damaged.
Unusual noise or vibration Loose mounting; Misaligned load; Damaged gearbox or bearings. Check and tighten mounting bolts; Ensure load is properly aligned; Contact support if internal damage is suspected.
Motor overheats Excessive load; Prolonged operation at peak current; High ambient temperature. Reduce load; Operate within rated current limits; Ensure adequate ventilation and ambient temperature is within specified range.

9. User Tips

No specific user tips were available from reviews or Q&A for this product at this time.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact STEPPERONLINE Official Store directly through your purchase platform or their official website.

An additional user manual in PDF format may be available for download. Please refer to the following link for more detailed documentation:

View User Manual (PDF)

© 2024 STEPPERONLINE. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.