eletechsup R421C32

Contents

eletechsup R421C32 32-Channel RTU RS485 Relay Module User Manual

Model: R421C32 | Brand: eletechsup

1. Introduction

The eletechsup R421C32 is a versatile 32-channel RTU RS485 Relay Module designed for various control applications, including home automation, PLC systems, and LED control. This module operates on a DC 12V power supply and communicates via a UART serial port using the MODBUS RTU protocol. It offers robust control capabilities for a wide range of devices.

eletechsup R421C32 32-Channel RTU RS485 Relay Module
Figure 1: Top view of the R421C32 32-Channel RTU RS485 Relay Module.

2. Package Contents

Upon opening the package, you should find the following item:

  • 1 x DC 12V 32 Channels R-S485 Modbus RTU Relay Module (Model: R421C32)
R421C32 Relay Module Package Contents
Figure 2: The R421C32 32-Channel RTU RS485 Relay Module as supplied.

3. Specifications

The R421C32 relay module features the following technical specifications:

FeatureSpecification
Model NumberR421C32
Brand Nameeletechsup
Channels32
Power SourceDC
Operating VoltageDC 12V
Standby Current (all relays closed)9mA
Current (all 32 relays open)1150mA
Bus InterfaceRS485
Communication ProtocolMODBUS RTU
Maximum Load10A / 250VAC, 10A / 125VAC
Contact LoadHigh Power
Dimensions (L x W x H)180 x 90 x 20 mm
Weight296g
CustomizationYes
OriginMainland China
R421C32 Relay Module with dimensions and interface labels
Figure 3: R421C32 module with indicated dimensions, weight, RS485 interface, dual power interface, and I/O terminals.

4. Setup and Wiring

Proper wiring is crucial for the safe and correct operation of the R421C32 module. Ensure all connections are secure before applying power.

4.1 Power Supply

The module requires a DC 12V power supply. Connect the positive (+) terminal of your 12V DC supply to the 'VIN' terminal and the negative (-) terminal to the 'GND' terminal on the module's dual power interface.

4.2 RS485 Interface

The RS485 interface is used for communication with a master device (e.g., PLC, PC). Connect the RS485 A+ terminal to the A+ of your master device, and the RS485 B- terminal to the B- of your master device. An optional RS485 GND terminal is also available.

4.3 Load Connections

The module provides 32 relay channels. Each channel has normally open (NO) and common (COM) terminals. Connect your loads according to the desired control circuit.

4.3.1 DC 12V Control Circuit

For controlling DC 12V loads, connect the positive side of the DC 12V power supply to one side of the load, and the other side of the load to the NO terminal of a relay. Connect the COM terminal of the same relay to the positive side of the DC 12V power supply. The negative side of the DC 12V power supply should be connected to the negative side of the load.

Wiring diagram for DC 12V control circuit
Figure 4: Wiring diagram for controlling DC 12V loads. 'LOAD' represents devices such as cameras, LED lights, or motors.

4.3.2 DC 1-110V or AC 85-265V Control Circuit

For controlling loads with voltages other than DC 12V (e.g., DC 1-110V or AC 85-265V), an additional DC 12V power supply is required for the module itself. The load's power source should be connected to the relay contacts. For example, connect one side of the load's power source to the COM terminal of a relay, and the other side of the load to the NO terminal of the same relay. The other side of the load's power source connects directly to the load.

Wiring diagram for DC 1-110V or AC 85-265V control circuit
Figure 5: Wiring diagram for controlling DC 1-110V or AC 85-265V loads. Note the requirement for a separate DC 12V power supply for the module.

4.4 Device Addressing (DIP Switches)

The module includes DIP switches (labeled A0-A5) for setting the device address when multiple modules are used in parallel on the same RS485 bus. Each module must have a unique address. Refer to the Modbus documentation for proper addressing configuration.

Modbus command diagram with PLC and multiple relay modules
Figure 6: Example of multiple R421C32 modules connected to a PLC via RS485, illustrating unique DIP switch settings for each module's address.
Modbus command diagram with PC and multiple relay modules
Figure 7: Example of multiple R421C32 modules connected to a PC via a USB to RS485 converter, showing unique DIP switch settings for each module's address.

5. Operating Instructions

The R421C32 module operates using MODBUS RTU commands over its RS485 serial interface. It supports up to 64 devices in parallel under the MODBUS command mode.

5.1 MODBUS RTU Commands

The module supports the following 6 commands for relay control:

  • 'open': Activates a relay.
  • 'close': Deactivates a relay.
  • 'Momentary': Briefly activates a relay and then deactivates it.
  • 'Self-locking': Toggles the state of a relay with each command.
  • 'Interlock': Ensures only one relay in a group is active at a time.
  • 'Delay': Activates a relay for a specified duration. The maximum delay is 255 seconds.
Image showing the 6 Modbus commands
Figure 8: The six primary Modbus commands supported by the R421C32 module.

5.2 Control Software

MODBUS commands can be sent using various methods:

  • Serial HyperTerminal (Serial Assistant): Requires manual addition of CRC (Cyclic Redundancy Check) to commands.
  • Modbus Poll Software: Automatically adds the CRC to commands, simplifying testing and control.
  • PLC or MCU Process Control: Integration into programmable logic controllers or microcontrollers for automated control.
Screenshot of Serial Port Tester software
Figure 9: Example interface of a Serial Port Tester (HyperTerminal) for sending serial commands.
Screenshot of Modbus Poll software
Figure 10: Example interface of Modbus Poll software for sending Modbus commands.

6. Applications

The R421C32 module is suitable for a variety of applications, including but not limited to:

  • Automated industry PLC systems
  • Smart Home and Home Automation systems
  • PTC Camera control
  • Security Monitoring systems
  • Identification systems
  • Motor Forward & Backward control
  • LED Home lighting control
  • Door Lock systems

7. Maintenance

To ensure the longevity and reliable operation of your R421C32 module, consider the following maintenance guidelines:

  • Environment: Operate the module in a clean, dry environment, free from excessive dust, moisture, and corrosive gases.
  • Temperature: Avoid exposing the module to extreme temperatures outside its specified operating range.
  • Cleaning: If cleaning is necessary, gently wipe the module with a dry, soft cloth. Do not use liquid cleaners or solvents.
  • Connections: Periodically check all wiring connections to ensure they remain secure and free from corrosion.

8. Troubleshooting

If you encounter issues with your R421C32 module, consider the following troubleshooting steps:

  • No Power: Verify that the DC 12V power supply is correctly connected and providing the correct voltage. Check for loose wires or faulty power adapters.
  • Communication Failure:
    • Ensure the RS485 A+ and B- connections are correct and not swapped.
    • Verify that the baud rate, data bits, stop bits, and parity settings in your control software match the module's settings.
    • Check if the module's DIP switch address is unique and correctly configured for your Modbus network.
    • Ensure the RS485 bus is properly terminated if it's a long or noisy line.
  • Relay Not Activating:
    • Confirm that the correct Modbus command is being sent to the correct relay address.
    • Check the load wiring for continuity and proper connection to the relay terminals.
    • Ensure the load's power supply is active and correctly connected.
  • Intermittent Operation: Check for electromagnetic interference (EMI) from nearby high-power devices. Ensure proper grounding and shielding if necessary.

9. User Tips

  • Modbus Addressing: When using multiple modules, always double-check that each module has a unique Modbus address set via its DIP switches to prevent communication conflicts.
  • CRC Calculation: If using a generic serial terminal, remember that Modbus RTU commands require a 16-bit CRC checksum. Many online tools or libraries can help generate this. Modbus Poll software typically handles this automatically.
  • Power Isolation: For sensitive applications or when controlling high-voltage/high-current loads, consider using opto-isolators or separate power supplies to protect the control circuitry from electrical noise or surges.
  • Testing: Before deploying in a critical application, thoroughly test each relay channel and communication command using a known working load and the recommended test software.

10. Warranty and Support

For warranty information, technical support, or further inquiries, please contact the manufacturer or your point of purchase. Ensure you have your product model number (R421C32) available when seeking support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.