DIVEDEER RA2-02

Contents

DIVEDEER RA2-02 Window Cleaning Robot User Manual

Model: RA2-02 | Brand: DIVEDEER

Introduction

Thank you for purchasing the DIVEDEER RA2-02 Window Cleaning Robot. This manual provides important information for the safe and efficient use of your new device. Please read it carefully before operation and keep it for future reference.

The DIVEDEER RA2-02 is an intelligent, ultra-thin window cleaning robot designed to clean various glass surfaces with its double water jet and powerful suction. It features intelligent path planning and can be operated via remote control.

DIVEDEER RA2-02 Window Cleaning Robot

Image: The DIVEDEER RA2-02 Window Cleaning Robot, highlighting its sleek design.

Important Safety Instructions and Warnings

1. General Safety

  • Do not allow children to operate this product. Users with physical, sensory, or psychological disorders, or those lacking knowledge of the product's functions, must be supervised by a fully competent user.
  • This product is designed to clean framed and frameless glass. If the window or glass frame has a damaged silicone rubber edge, exercise caution to prevent leakage or falling during cleaning.
  • Always ensure the product is used safely and securely, especially on frameless glass.
  • Strictly follow this manual for proper use.
  • Do not immerse this product in liquids (e.g., beer, water, drinks) or leave it in a humid environment for extended periods.
  • Do not expose this product to direct sunlight or heat sources (e.g., radiators, heaters, microwave ovens, gas stoves).
  • Do not place this product in strong magnetic fields.
  • Store this product out of reach of children.
  • Use this product only in ambient temperatures between 0°C and 40°C (32°F and 104°F).
  • Do not clean damaged glass or objects with uneven surfaces, as the vacuum suction may not be sufficient.
  • The built-in battery should only be replaced by the manufacturer or a designated service center to avoid hazards.
  • Disconnect power before removing or handling the battery.
  • Improper use may result in property damage or personal injury; the manufacturer is not responsible for such incidents.

2. Electrical Safety

  • Use only the original adapter. Non-original adapters may cause product failure or damage.
  • Ensure adequate ventilation and heat dissipation for the adapter during use. Do not wrap the power adapter.
  • Do not use the adapter in a humid environment or touch it with wet hands.
  • Charge the window cleaner at the voltage specified for the power adapter.
  • Do not use a damaged power adapter, charging cable, or power plug.
  • Before cleaning or maintaining the machine, unplug the power cord. Do not disconnect power by unscrewing the extension cord.
  • Do not disassemble the power adapter. If faulty, replace the entire power adapter. Contact customer service for assistance.

3. Battery Safety

  • Improper handling of the product battery carries a risk of combustion or chemical injury. Do not disassemble the battery to prevent short circuits.
  • Do not use or store the battery in fire or high-temperature environments above 60°C.
  • Dispose of used batteries at a local professional waste battery recycling center in accordance with national laws and regulations.

4. Operational Warnings

  • Before operation, ensure the safety rope is securely attached to the machine and a stable indoor object. Check the rope for damage and secure knotting.
  • When cleaning glass without a blocking frame (e.g., a balcony railing), set up a safety warning area below.
  • Fully charge the built-in backup battery before use (indicated by a green light).
  • Do not use in rainy or wet weather conditions.
  • Turn on the machine first, then place it on the window glass.
  • Ensure the machine is safely attached to the window surface before releasing your hands.
  • Before turning off the machine, hold it to prevent dropping.
  • Do not use this product to clean frameless windows or glass without proper precautions.
  • Ensure the cleaning cloth is properly attached to prevent air leakage.
  • Do not spray water directly onto the machine or its bottom; spray water only onto the cleaning cloth.
  • Remove any items from the glass surface before use.
  • Keep hair, loose clothes, fingers, and other body parts away from the machine's working parts.
  • Do not use the machine in areas with flammable or explosive solids or gases.

Attention: Safety Rope

  1. Before use, ensure the safety rope is intact and one end is firmly connected to the machine. The other end must be securely attached to other objects in the room to prevent the Window Cleaning Robot from falling.
  2. If the window glass glue is falling off in the middle section or chipped at the corners due to aging, use the machine carefully and supervise it during operation.
Safety rope attachment diagram

Image: Diagram showing proper safety rope attachment.

Product Description

Key Features

  • Vacuum Motor: Enables the machine to adhere to glass surfaces and move freely on vertical glass.
  • Power Failure Protection (UPS): A built-in backup battery provides power to prevent the equipment from falling during power outages.
  • Dual Cleaning Wheels: Two well-designed cleaning wheels with suction cups facilitate movement and cleaning.
  • Microfiber Cleaning Cloths: Easily removable and replaceable microfiber cloths ensure effective cleaning.
  • Artificial Intelligence: The robot plans its path, detects frames, and automatically cleans the entire window.
  • Manual Remote Control: Allows for free manual control of the robot.
  • Upgraded Design: Features advanced AI technology, a fashionable appearance, and a lighter, thinner body for enhanced cleaning performance in various home environments.
  • Double Water Spray: Equipped with twin-jet bilateral atomization spraying for thorough cleaning.
  • Powerful Suction: 2800Pa to 3000Pa adsorption force for firm adherence to glass.
Intelligent Dual Spray Window Cleaning Robot features

Image: Key features of the intelligent dual spray window cleaning robot, including ultra-thin body, wet and dry wiping, and 6 cleaning cloths.

Fully Upgraded Safe and Intelligent features

Image: Detailed features of the upgraded robot, showing 2800Pa suction, twin-jet spray, intelligent planning, and modular structure.

Product Components

Familiarize yourself with the parts of your window cleaning robot:

Product component diagram

Image: Diagram illustrating the main components of the robot, including water tank, water spout, one-button start, power socket, cleaning ring, remote control receiving window, and power lights.

  • Water Tank: Reservoir for cleaning solution.
  • Water Spout: Dispenses cleaning solution onto the glass.
  • One-button Start: Initiates or pauses cleaning.
  • Power Socket: Connects to the power adapter.
  • Cleaning Ring: Holds the cleaning cloth.
  • Remote Control Receiving Window: Receives signals from the remote control.
  • Safety Rope Hanging Hole: Point for attaching the safety rope.
  • Power Light:
    • Blue light: Robot is operating normally.
    • Red light: Robot abnormality.

Product Accessories

The package includes the following items:

  • 1 x Host (Window Cleaning Robot)
  • 1 x Power Cord + Adapter
  • 1 x Remote Control
  • 2 x Pairs of Cleaning Rings
  • 1 x Extension Cord (4 meters)
  • 1 x Safety Rope
  • 6 x Cleaning Cloths
  • 1 x User Manual (English)
  • 1 x Spray Bottle
Product accessories

Image: Visual representation of the product and its included accessories: host, adapter + power cord, cleaning cloth, safety rope, spray bottle, user manual, and remote control.

Specifications

FeatureSpecification
Model NumberRA2-02
Brand NameDIVEDEER
OriginMainland China
CertificationROHS, CE, FCC, UL, CCC
Input VoltageAC 200-240V 50Hz-60Hz
Rated Power72W
Power (W)<800W
Voltage100 - 240 V
Battery Capacity500mAh
Suction Power2500-3000Pa
Power Failure Protection Time10 minutes
Control MethodRemote Control
Noise Level68dB
Border DetectionAutomatic
Fall Arrest ControlPower failure protection (backup battery) safety rope
Cleaning ModeIntelligent path planning modes
Water Tank Capacity60ml
Water Spraying MethodManual / Auto (Double water spray)
Electric MotorBrushed motor
Cleaning Cloths Included6 PCS
Net Weight1250g
External Dimensions265 x 130 x 85mm
Product specifications table

Image: Detailed product information table, including model, motor type, function, voltage, power, suction, cleaning speed, battery, and noise.

Setup Guide

1. Power Connection

  1. Insert the threaded connector into the power connector of the robot's fuselage and tighten it.
  2. Connect the AC power cord to the adapter.
  3. Plug the power cord into a wall socket.
Power connection steps

Image: Visual guide for connecting the power adapter and cord to the robot.

2. Fully Charge Before Use

The built-in battery provides standby power in case of power failure. Ensure it is fully charged before use.

  1. Turn on the power switch on the robot, connect the power cord. The red light will turn on, indicating charging.
  2. When the red light turns off, the battery is fully charged.

3. Attach the Safety Rope

  1. Check the safety rope for damage and ensure the knot is secure before use.
  2. Fasten the safety rope securely to a fixed object indoors to prevent the robot from falling.
Safety rope attachment steps

Image: Step-by-step diagram for attaching and securing the safety rope to the robot and a fixed object.

4. Install the Cleaning Cloth and Ring

Ensure the cleaning cloth is correctly placed on the cleaning wheel to prevent air leakage.

Cleaning cloth installation diagram

Image: Diagram showing the correct placement of the cleaning cloth and ring.

5. Add Water to the Tank

  1. Do not add any other cleaning agents to the water tank. Use only clean, impurities-free water.
  2. Turn the machine over, remove the cleaning ring, open the silicone cover, and add water.
  3. Fill the water tank to about 80% capacity to maintain stable air pressure.
Water tank filling steps

Image: Diagram illustrating how to access and fill the water tank.

6. Attach the Machine to the Glass

  1. Turn on the power switch.
  2. Press and hold the start button for 2 seconds, confirming that the fan rotates.
  3. Place the machine on the glass, keeping a certain distance from the window frame.
  4. Ensure the robot is securely attached to the glass before releasing your hands.
Attaching robot to glass

Image: Steps for turning on the robot and attaching it to the window glass.

Operating Instructions

1. Cleaning Modes

Smart navigation cleaning paths

Image: Illustration of the robot's smart navigation and cleaning paths on a window.

Multiple cleaning surfaces and scenarios

Image: Examples of various surfaces and scenarios where the robot can be used, including single/double/multiple glazing, marble tile, kitchen/bathroom glass, glass with/without border, high/low floor exterior windows, and mirrors.

Dry Wipe

  • For the first wipe, always perform a "dry wipe" without spraying water to remove surface sand.
  • Spraying water or detergent on the cleaning cloth or glass first may mix with sand and create yellow residue, reducing cleaning effectiveness.
  • Dry wiping is best in sunny or low-humidity weather.

Wet Wipe (Dual Water Spray)

The robot has two water spouts. It sprays water from the left spout when cleaning left and from the right spout when cleaning right.

  • Automatic Water Spray:
    • When the robot starts cleaning, automatic intermittent water spraying is enabled by default.
    • Press the "AU" button on the remote control once to turn off automatic spray (robot beeps once).
    • Press the "AU" button again to turn on automatic spray (robot beeps twice).
  • Manual Water Spray:
    • During cleaning, press the spray button on the remote control to spray water once.

2. Intelligent Path Planning Modes

The robot uses intelligent path planning for efficient cleaning:

  • Climb to the top and then automatic clean: The robot ascends to the top and cleans downwards.
  • Auto clean from right to left: The robot cleans horizontally from right to left.
  • Auto clean from left to right: The robot cleans horizontally from left to right.
Intelligent path planning modes

Image: Diagrams illustrating different intelligent cleaning path patterns.

3. Remote Control Functions

The remote control allows for various operations:

Remote control functions

Image: Remote control with buttons for various functions like automatic cleaning, manual movement, and water spray.

  • Battery Installation: Use AAA/RL batteries of the specified type. Align the negative pole with the spring first, press down, and then cover the battery cover. Do not mix new and old batteries or different types.
  • Buttons:
    • Up arrow: Manual upward movement
    • Down arrow: Manual downward movement
    • Left arrow: Manually move to the left
    • Right arrow: Manually move to the right
    • "AU" button: Automatic water spray (toggle on/off)
    • Spray icon: Manual water spray (single spray)
    • Play/Pause icon: Start/Pause cleaning
    • Other buttons for specific path planning modes (e.g., climb to top, auto clean right to left, auto clean left to right).

4. Cleaning Completion

  1. Hold the window cleaner with one hand and press the power button for 2 seconds with the other hand to turn off the power.
  2. Remove the window cleaning robot from the window.
  3. Turn off the power switch to extend the life of the backup battery.
  4. Untie the safety rope and store the machine and accessories in a dry, ventilated environment for next use.
Cleaning completion steps

Image: Visual guide for safely removing the robot after cleaning and storing it.

Maintenance

  • Cleaning Cloths: Regularly check and replace cleaning cloths, especially if they are dirty or leaving marks. Dampen and wring out cloths before use for better effect.
  • Water Tank: Ensure the water tank contains clean, impurities-free water. Clean the ultrasonic nozzle with a soft cloth if water spray issues occur.
  • Storage: After use, untie the safety rope and store the machine and its accessories in a dry and ventilated environment.
  • Power Adapter: Do not use water to clean the machine body or power adapter.
  • General Cleaning: Make sure the power is completely disconnected and the machine is off before cleaning or maintaining the body.

Power Failure Protection (UPS)

The robot is equipped with a built-in backup battery for power failure protection.

  • In the event of a power failure, the robot will automatically switch to its built-in backup battery, which can last for up to 10 minutes (when fully charged).
  • During a power failure, the machine will remain in place and will not move. The blue lights will flash, and a warning sound will be emitted.
  • Retrieve the robot as soon as possible to prevent it from falling due to prolonged power loss.
  • To retrieve, gently pull the device back using the safety rope, keeping the rope as close to the glass as possible to avoid sudden detachment.
Power failure protection diagram

Image: Diagram illustrating the robot's behavior during a power failure and how to retrieve it using the safety rope.

Troubleshooting

1. Robot runs slowly or fails during first use (especially on dirty outer windows):

  • Cause: Cleaning cloth too dirty, low friction (glass stickers, fog stickers), glass too clean (too slippery), low humidity (air-conditioned room).
  • Solution:
    1. Ensure the cleaning cloth is clean.
    2. Spray a small amount of water or glass cleaner evenly on the cleaning cloth or the glass surface.
    3. Dampen and wring out the cleaning cloth before placing it on the cleaning ring.

2. Robot cannot detect the upper edge of the window or slides when pressing the up automatic cleaning button:

  • Solution: Press the appropriate button on the remote control to switch to a different auto-clean mode.

3. Robot cannot wipe the upper left side of the glass:

  • Cause: Glass or cleaning cloth is slippery, wider wiped glass area, or top line slides slightly.
  • Solution: Use the remote control's manual window cleaning mode to clean the unwiped area.

4. Machine finishes cleaning early without completing the window:

  • Solution: Press the appropriate button on the remote control to continue the unfinished part in auto window mode.

5. Robot slips or fails to climb:

  • Cause: Friction too small (glass stickers, thermal insulation stickers, fog stickers), cleaning cloth too wet, glass too clean (too slippery), low humidity.
  • Solution: When starting, place the machine at a distance from the window frame to avoid incorrect judgment.

6. Robot does not run smoothly:

  • Cause: Dirty cleaning cloth, different surface areas (glass, sticker, thermal insulation), loose cleaning wheel screw.
  • Solution:
    1. Replace the cleaning cloth.
    2. Ensure the robot is used on a single type of surface.
    3. Tighten the cleaning wheel screw (do not overtighten, as it may affect glass glue thickness or beveled window frame performance).

7. Round wheel marks remain on the glass after cleaning:

  • Cause: Cleaning cloth is too dirty.
  • Solution: Replace with a clean cloth and wipe again.

8. Warning sound and red light flashing when robot stops due to power failure:

  • Solution:
    1. Gently pull the safety rope back to the robot, keeping it close to the glass.
    2. Turn off the robot power switch.
    3. Check the wire for poor contact or breakage.

9. Robot stops with red light flashing and no warning sound (unknown obstacles):

  • Solution:
    1. Use the remote control to move the robot to a safe position, or gently pull the safety rope back, keeping it close to the glass.
    2. Remove any obstacles on the window.
    3. Check for air leaks.

10. Arc marks on polished glass when light shines at night:

  • Solution (First time): Turn off water spraying, use a clean cloth to remove sand.
  • Solution (Second wipe): Clean and replace the cloth, turn on water spraying, or keep the upper cleaning wheel clean/dry and spray a little detergent/alcohol on the lower cleaning wheel (1-2 sprays) to eliminate arc traces. Note: All wet cleaning cloths will affect operation.

11. Robot cleans all windows but doesn't stop automatically:

  • Solution: Press the stop button on the remote control.

12. Robot does not spray water:

  • Solution:
    1. Confirm the water spray function switch is on.
    2. Clean the ultrasonic nozzle with a clean soft cloth.
    3. Check the water tank for water and ensure the cleaning solution is clean and pure.

User Tips

  • For optimal cleaning, especially on very dirty windows, perform an initial dry wipe to remove loose dirt before proceeding with wet cleaning.
  • Always ensure the safety rope is securely fastened to a stable anchor point before operating the robot, particularly on high windows.
  • If the robot seems to struggle or leave streaks, check the cleaning cloths first. They might be too dirty or too dry/wet. Having a few clean, slightly damp cloths ready can improve performance.
  • When adding water, use only clean water to prevent clogging the spray nozzles. Avoid using harsh detergents directly in the tank unless specifically recommended by the manufacturer.
  • If you experience issues with the robot's movement or suction, verify that the cleaning cloths are properly attached and there are no air leaks.

Warranty and Support

Certifications

The entire machine has passed CE, FCC, ROHS quality testing and certification. The power supply passes CCC, CE, FCC, UL, and ROHS safety testing and certification.

Contact and Assistance

If you have any questions or encounter problems with the product, please contact customer service. When reporting issues, providing a complete unboxing video and a video demonstrating the problem (e.g., machine not working after following instructions) can help expedite resolution.

For further details, you may refer to the official user manual PDF: User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.