Estardyn 2.0 Inch 240x320 TFT LCD Display Module

Contents

Estardyn 2.0 Inch 240x320 TFT LCD Display Module User Manual

Model: 2.0 Inch 240x320 TFT LCD Display Module

1. Introduction

This manual provides detailed instructions for the Estardyn 2.0 Inch 240x320 Full Color TFT LCD Display Module. This module features an ST7789 controller and supports both SPI and 8-bit parallel interfaces, making it versatile for various microcontroller projects, including Arduino. Please read this manual thoroughly before attempting to set up or operate the module.

Front and back view of the Estardyn 2.0 inch TFT LCD module
Figure 1: Front and back view of the Estardyn 2.0 inch TFT LCD module, showing the display and connection pins.

2. Specifications

The following table outlines the key technical specifications of the Estardyn 2.0 Inch TFT LCD Display Module:

Product Parameter image listing specifications
Figure 2: Detailed product parameters.
FeatureSpecification
Display Size2.0 inches
Resolution240x320 pixels
Driver ICST7789
Interface Type4-wire SPI / 8-bit Parallel Port
Display ColorFull Color
Power Supply2.8V ~ 3.3V
Screen Size (mm)34.6 * 47.8 * 2.03
Module Size (mm)37.5 * 58.04 * 6.5
Display Area (mm)30.6 * 40.8
Operating Temperature-20°C ~ 70°C
Link TypeCOG
Module dimensions and pin definition table
Figure 3: Module dimensions and pin definition.

3. Setup and Connection

This module supports two main communication interfaces: 4-wire SPI and 8-bit Parallel (8080). The interface selection is done via onboard jumpers (resistors R3, R5, R6).

3.1 Pin Definitions

Refer to the table below for the function of each pin on the module:

PINSYMBOLDescription
1GNDGround
2VDDPower Supply (2.8V-3.3V)
3SCLSerial Clock (SPI) / Write Strobe (Parallel)
4SDASerial Data (SPI) / Data Bus (Parallel)
5RESReset Pin
6DCData/Command Selection
7CSChip Select
8BLBacklight Control

3.2 Interface Selection

The module's interface mode is configured by soldering specific resistors (jumpers) on the back of the PCB. Please ensure the correct resistors are soldered for your desired interface before connecting the module.

Detailed back view of the TFT LCD module showing interface selection jumpers
Figure 4: Back view of the module, indicating R3, R5, and R6 for interface selection.
  • For 4-wire SPI Interface: Solder resistors R3 and R5.
  • For 8-bit Parallel (8080) Interface: Solder resistors R3 and R6.

Caution: Ensure only the resistors for the desired interface are soldered. Incorrect configuration can lead to malfunction or damage.

3.3 Connecting to a Microcontroller (e.g., Arduino)

Once the interface is selected, connect the module to your microcontroller according to the chosen interface. Below are general guidelines:

  • Power: Connect VDD to 3.3V and GND to Ground on your microcontroller.
  • Reset (RES): Connect to a digital pin on your microcontroller.
  • Data/Command (DC): Connect to a digital pin on your microcontroller.
  • Chip Select (CS): Connect to a digital pin on your microcontroller.
  • Backlight (BL): Connect to 3.3V for constant backlight, or to a PWM-capable digital pin for brightness control.
  • For SPI Interface:
    • SCL (Serial Clock) to SPI Clock pin (e.g., D13 on Arduino Uno).
    • SDA (Serial Data) to SPI MOSI pin (e.g., D11 on Arduino Uno).
  • For 8-bit Parallel Interface:
    • SCL (Write Strobe) and SDA (Data Bus) will require additional data pins (D0-D7) and control pins (RD, WR, RS, CS) depending on the specific parallel implementation. Refer to the ST7789 datasheet for full parallel wiring details.

4. Operation

To operate the display, you will need appropriate software libraries for your chosen microcontroller and interface. For Arduino, libraries such as Adafruit_GFX and Adafruit_ST7789 are commonly used.

  1. Install Libraries: Download and install the necessary display libraries for your development environment (e.g., Arduino IDE Library Manager).
  2. Initialize Display: In your code, initialize the display object, specifying the pins connected for CS, DC, RES, and BL (if controlled).
  3. Basic Functions:
    • display.init(): Initializes the display controller.
    • display.setRotation(): Sets the screen orientation (0-3).
    • display.fillScreen(color): Fills the entire screen with a specified color.
    • display.setTextSize(size): Sets the size of text.
    • display.setTextColor(color): Sets the color of text.
    • display.setCursor(x, y): Sets the text cursor position.
    • display.print("Hello World"): Prints text to the display.
    • display.drawPixel(x, y, color): Draws a single pixel.
    • display.drawRect(x, y, w, h, color): Draws a rectangle.
    • display.fillRect(x, y, w, h, color): Fills a rectangle.
  4. Upload Code: Compile and upload your code to the microcontroller.

Refer to the examples provided with the display libraries for more advanced usage, such as displaying images, drawing shapes, and implementing user interfaces.

TFT LCD module displaying a trophy graphic
Figure 5: Example of the display module in operation.

5. Maintenance and Care

  • Handling: Handle the module by its edges to avoid touching the display surface or the delicate FPC (Flexible Printed Circuit) connector.
  • Cleaning: Use a soft, lint-free cloth, slightly dampened with distilled water or an electronics-safe screen cleaner, to gently wipe the display surface. Avoid abrasive materials or harsh chemicals.
  • Storage: Store the module in an anti-static bag in a cool, dry environment, away from direct sunlight and extreme temperatures.
  • Power: Always ensure the correct power supply voltage (2.8V-3.3V) is applied. Over-voltage can permanently damage the module.
  • Static Electricity: Take precautions against electrostatic discharge (ESD) when handling the module, as it can damage sensitive electronic components.

6. Troubleshooting

No Display / Blank Screen:
  • Check power connections (VDD, GND) and ensure the voltage is within the specified range (2.8V-3.3V).
  • Verify that the backlight (BL) pin is correctly connected and receiving power.
  • Ensure the correct interface (SPI or Parallel) is selected via the R3/R5 or R3/R6 jumpers.
  • Double-check all data and control pin connections to the microcontroller.
  • Confirm that the display initialization code in your software is correct and running.
  • Try a different set of pins on your microcontroller if possible, or test with a known working example sketch.
Incorrect Colors / Garbled Display:
  • Verify that the correct display library and driver (ST7789) are being used.
  • Check for loose connections or short circuits on the data lines.
  • Ensure the correct color mode (e.g., RGB565) is configured in your software.
  • Confirm the display rotation setting is appropriate for your application.
Display Freezes or Responds Slowly:
  • Check the microcontroller's processing load. Complex graphics operations can be demanding.
  • Ensure your SPI clock speed is not too high for the module or too low for your application.
  • Verify power supply stability.

7. User Tips

  • Software Compatibility: For Arduino users, the Adafruit_ST7789 library, combined with Adafruit_GFX, provides a robust and well-documented solution for controlling this display.
  • Backlight Control: Connecting the BL pin to a PWM-capable pin on your microcontroller allows for dynamic brightness adjustment, which can save power and improve user experience.
  • Voltage Level Shifters: If your microcontroller operates at 5V (e.g., Arduino Uno), consider using a logic level shifter for the data and control pins to protect the 3.3V display module.
  • Example Code: Always start with simple example code provided by the library developers to confirm basic functionality before integrating into a larger project.

8. Warranty and Support

For any technical assistance, warranty claims, or further inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.