ETAxopowo DIY Electronic Watch Kit

Contents

ETAxopowo DIY Electronic Watch Kit User Manual

Model: DIY Electronic Watch Kit | Brand: ETAxopowo

1. Introduction

Welcome to the exciting world of electronics with your new ETAxopowo DIY Electronic Watch Kit! This kit provides a hands-on experience in soldering and assembling a functional digital watch with an LED display and a comfortable silicone strap. This manual will guide you through each step of the assembly process, operation, and maintenance to ensure a successful and enjoyable project.

2. Package Contents

Before you begin, please verify that all components listed below are present in your kit:

Components of the DIY watch kit including PCB, digital tube, resistors, capacitors, battery, battery shrapnel, switches, screwdriver, shell, and silicone strap.

Figure 1: DIY Watch Kit Components

  • PCB (Printed Circuit Board)
  • Digital Tube (LED display)
  • Microcontroller (IC chip)
  • Resistors (R1)
  • Ceramic Capacitors (22P for C1, C2; 104P for C3)
  • Crystal Oscillator (Y1)
  • Tact Switches (S1, S2)
  • Battery Shrapnel (BT1)
  • CR2032 Lithium Battery (3V)
  • Transparent Shell (upper and lower parts)
  • Silicone Strap
  • Screwdriver
  • Small Screws

3. Assembly Instructions

This kit requires basic soldering skills. Please follow the steps carefully. Refer to the assembly video and diagrams for visual guidance.

Video 1: DIY Watch Kit Assembly Tutorial

Detailed assembly steps for the DIY watch kit, showing soldering of components, battery installation, and casing assembly.

Figure 2: Assembly Steps Overview

  1. Solder Resistor (R1): Install the resistor at position R1. There is no positive or negative direction for resistors.
  2. Solder Tact Switches (S1, S2): Weld the Tact Switches at positions S1 and S2. Ensure the welding temperature is not too high and install them straight, not crooked.
  3. Solder Microcontroller (U1): Install the microcontroller at position U1. Pay close attention to the notch direction on the chip and ensure it is consistent with the diagram.
  4. Solder Crystal Oscillator (Y1): Install the crystal oscillator at Y1 position. It does not have a specific direction. Leave the pins slightly longer for easier soldering.
  5. Solder Ceramic Capacitors (C1, C2, C3): Install the 104P ceramic disc capacitor in position C3, and the 22P ceramic disc capacitors in positions C1 and C2. These components have no polarity.
  6. Solder Digital Tube (LED1): Install the digital tube at the position of LED1. Ensure the decimal point is at the bottom and pay attention to the installation direction.
  7. Install Battery Shrapnel (BT1): Weld the battery holder at position BT1. Ensure the opening direction is outward so the battery can be inserted correctly.
  8. Install Button Battery: Install the CR2032 button battery as shown in the picture, with the '+' pole facing upwards. The CR2032 button battery is an optional accessory.
  9. Install Circuit Board into Upper Casing: Carefully place the assembled circuit board into the upper transparent casing. Tilt it slightly and install the switch direction first.
  10. Install Bottom Shell: Attach the bottom transparent shell to the upper casing.
  11. Secure with Screws: Secure the casing with the 4 provided screws. Do not use excessive force; just tighten them in place.
  12. Install Watch Strap: Install the watch strap. Insert one side first, then hold down the other side of the shrapnel card to secure it.
Circuit diagram for the DIY electronic watch kit, showing connections for the microcontroller, LED display, battery, and switches.

Figure 3: Schematic Diagram

4. Operating Instructions

Hand wearing the DIY watch, showing the LED digital tube display with time '8:8:8:8'.

Figure 4: Digital Tube Display in Use

  • Display Time: Press any button (S1 or S2) to display the time. The display will automatically turn off after 10 seconds to conserve battery.
  • Set Minutes: Long press button S1 to adjust the minutes.
  • Set Hours: Long press button S2 to adjust the hours.
  • 24-Hour Display: To enable 24-hour display, short circuit the designated solder joints on the back of the PCB.
Labeled diagram of the electronic watch showing components like singlechip, S1, LED digital tube, CR2032 battery, S2, shell, and silicone strap.

Figure 5: Watch Component Overview

5. Maintenance

  • Cleaning: Gently wipe the watch casing and strap with a soft, dry cloth. Avoid using harsh chemicals or abrasive materials.
  • Water Resistance: This watch is not waterproof. Avoid exposure to water, moisture, or high humidity to prevent damage to the electronic components.
  • Battery Replacement: When the display becomes dim or stops working, it's time to replace the CR2032 battery. Carefully open the back casing, remove the old battery, and insert a new one with the positive (+) side facing up.
  • Storage: Store the watch in a cool, dry place when not in use.

6. Troubleshooting

  • Watch not turning on:
    • Check if the CR2032 battery is correctly installed with the positive side up.
    • Ensure the battery has sufficient charge. Replace if necessary.
    • Verify all soldered connections are secure and there are no short circuits.
  • Incorrect time display:
    • Follow the operating instructions to reset the minutes and hours using buttons S1 and S2.
    • Ensure the crystal oscillator is properly soldered.
  • Buttons not responding:
    • Check the soldering of the Tact Switches (S1, S2) to ensure good contact.
    • Ensure the switches are not installed crooked or damaged.
  • LED display issues:
    • Verify the digital tube is correctly installed and soldered, paying attention to its direction.
    • Check the soldering of the microcontroller and ceramic capacitors.

7. Specifications

FeatureDetail
Product TypeDIY Electronic Watch Kit (Module)
Display TypeLED Digital Tube
Strap MaterialSilicone
Battery TypeCR2032 3V Lithium Battery
Watch Face DimensionsApprox. 45mm (width) x 50mm (length) x 16mm (thickness)
Strap Length (each side)Approx. 90mm and 120mm
Package Dimensions15cm x 10cm x 4cm
Package Weight0.1 kg
OriginMainland China
Product size diagram showing dimensions of the watch face and strap in millimeters.

Figure 6: Product Dimensions

8. User Tips

  • Take your time with the soldering. A clean solder joint is key to a functional and durable watch.
  • Double-check component orientation, especially for the microcontroller and digital tube, before soldering.
  • Ensure all excess wire leads are trimmed after soldering to prevent short circuits.
  • The assembly process is designed to be straightforward, making it a satisfying project even for beginners.

9. Warranty and Support

For detailed information regarding warranty, returns, and additional support, please refer to the official user manual PDF provided by the seller. This document contains comprehensive information that may not be fully covered in this guide.

You can access the official user manual (PDF) here.

© 2023 ETAxopowo. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.