1. Introduction
This manual provides essential information for the safe and efficient operation of your PowMr 60A ULTRA MPPT Solar Charger Controller. This advanced Maximum Power Point Tracking (MPPT) solar charge controller is designed to optimize the power output from your solar panels to efficiently charge your battery bank. It supports 12V, 24V, 36V, and 48V battery systems and is compatible with various battery types, including sealed lead-acid, vented gel, and lithium batteries.
The controller features a built-in DSP controller for high performance, a 3-stage charging process to optimize battery life, and comprehensive protection functions. It is suitable for a wide range of applications, from RVs and camping setups to home storage and larger solar power systems.
2. Product Features
- MPPT 60A solar charge controller with 100% MPPT technology.
- Supports parallel operation for up to 12 units.
- 0 Layer design for easy installation and setup.
- Built-in DSP controller for high performance.
- 3-stage charging optimizes battery performance and extends battery life.
- Automatic detection of 12V/24V/36V/48V DC system voltages.
- High tracking efficiency up to 99% and peak conversion efficiency of 98%.
- Comprehensive protection features: Overcharge protection, Input PV polarity reverse protection, Output limited current protection, Over-temperature protection, Over-discharging protection, Short circuit protection.
- Troubleshooting promotion function.
- Suitable for various battery types: sealed lead-acid, vented gel, NiCd, and lithium batteries (user-defined voltage for other battery types).
- Easy to be mounted.
- Adaptive Boost Charging: Monitors battery response to determine optimal boost stage duration, preventing overcharging.
3. Installation and Setup
3.1 Wiring Connections
Follow the connection order carefully to ensure proper and safe operation. Always connect the battery first, then the solar panels, and finally the load.
- Connect Battery: Connect the battery to the controller. Ensure correct polarity.
- Connect Solar Panels: Connect the solar panels to the controller. Ensure correct polarity and that the PV input voltage is within the specified range.
- Connect Load: Connect your DC load to the controller.
Recommended wire gauge for connections: 7AWG (10 m2) - 5AWG (16 m2).
3.2 Battery Type Selection
The controller is compatible with various battery types. The default setting is for Sealed batteries. For other battery types (Vented, Gel, NiCd, Lithium), you may need to adjust the settings. Refer to the 'Operation' section for parameter setting instructions.
4. Operation
4.1 LCD Display and Button Functions
The controller features an LCD display and four buttons for viewing values and setting parameters:
- PV Button: View PV parameters (voltage, current, power).
- BAT Button: View battery parameters and set battery type.
- DC/Load Button: View and set load parameters.
- SET Button: Enter parameter setting mode and confirm changes.
4.2 Work Modes
The controller operates in different work modes:
- 3.0 Night mode: No charging.
- 4.0 MPPT tracking mode: Maximum Power Point Tracking, no charging.
- 7.0 Constant charge mode: Charging.
- 8.0 Floating charge mode: Charging.
4.3 Load Modes
The load output can be configured with the following modes:
- 00H: Load Turn Off.
- 24H: Load always Turn On.
- 01H-23H: Time Control (set load on's duration).
4.4 Parameter Setting
To adjust parameters:
- Press and hold the "Batt/up" or "DC Button" until the value flashes.
- Use the "up" or "down" button to adjust the value.
- Press "SET" to confirm and save the new value.
4.5 One-Click Factory Reset
To reset the controller to its factory default settings, long-press the "SET" button. All configurable settings will revert to their original values after the reset.
5. Maintenance
Regular maintenance ensures the longevity and optimal performance of your solar charge controller:
- Cleanliness: Keep the controller clean and free from dust and debris. Use a dry cloth for cleaning.
- Connections: Periodically check all wiring connections to ensure they are tight and secure. Loose connections can lead to power loss or overheating.
- Ventilation: Ensure adequate airflow around the controller to prevent overheating. Do not block ventilation openings.
- Environment: Operate the controller within its specified operating temperature and humidity ranges. Avoid exposure to direct sunlight, rain, or excessive moisture.
- Battery Health: Monitor your battery bank's health and ensure it is properly maintained according to the battery manufacturer's guidelines.
6. Troubleshooting
The PowMr 60A ULTRA MPPT Solar Charger Controller is equipped with several protection features to prevent damage. If you encounter issues, check the following:
- No Charging:
- Verify solar panel connections and polarity.
- Check PV input voltage to ensure it's within the controller's operating range.
- Ensure sufficient sunlight is reaching the solar panels.
- Battery Not Fully Charged:
- Confirm the correct battery type is selected in the controller settings.
- Check battery health and capacity.
- Ensure PV input power is sufficient for the battery bank size.
- Load Not Working:
- Check load connections and polarity.
- Verify the load mode setting (e.g., not set to '00H' - Load Turn Off).
- Ensure battery voltage is above the low voltage disconnect threshold.
- Error Codes/Indicators: Refer to the controller's display for any error codes or warning indicators. Consult the full product manual (if available) for specific code meanings.
6.1 Protection Features
The controller includes the following built-in protections:
- Overcharging Protection: Prevents battery damage from excessive charging.
- Overload Protection: Protects the system from excessive current draw by the load.
- Over-discharging Protection: Disconnects the load to prevent deep discharge of the battery.
- Reverse Polarity Protection: Protects the controller and system from incorrect wiring of PV input or battery.
- Short Circuit Protection: Safeguards against short circuits in the load or battery connections.
- Over-temperature Protection: Shuts down or reduces power if the controller's internal temperature exceeds safe limits.
7. Specifications
Below are the technical specifications for the PowMr 60A ULTRA MPPT Solar Charger Controller:
| Category | Parameter | 60A Model |
|---|---|---|
| Solar Input Specification | ||
| Max. Solar Array Open-Circuit Voltage | 160Vdc | |
| Maximum Input Power | For 12V System | 720W 20-80Vdc |
| For 24V System | 1440W 37-105Vdc | |
| For 36V System | 2100W 50-160Vdc | |
| For 48V System | 2800W 72-160Vdc | |
| Charge Mode | ||
| Charging Technology | MPPT | |
| Charging Algorithm | 3 Stages | |
| Nominal System Voltage | 12V/24V/36V/48V | |
| Battery Voltage Range | 9~60V | |
| Rated Charging Current | 60A | |
| Conversion Efficiency | ≤98% | |
| MPPT Efficiency | >99% | |
| Self-Consumption | 0.7W-1.2W | |
| Environment Specification | ||
| Operating Temperature Range | -35℃~+45℃ | |
| Humidity Range | ≤95%,Non-condensing | |
| Altitude | <3000m | |
| Protection Level | IP32 | |
| Parallel Function | Up to 12 Units in Parallel | |
8. User Tips
- For optimal performance, ensure your solar panel array's voltage and power are well-matched to your battery bank's nominal voltage and the controller's maximum input specifications.
- When connecting multiple units in parallel, ensure all controllers are configured identically for consistent system operation.
- Consider using appropriate circuit breakers or fuses on both the PV input and battery output lines for additional safety.
- If using lithium batteries, ensure the battery type settings are correctly configured to match your specific battery's charging requirements.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.
Manufacturer: PowMr
Certification: CE