JIKONG JK-PB2A16S20P V19

Contents

JIKONG V19 JK-PB2A16S20P Smart BMS User Manual

Model: JK-PB2A16S20P V19

1. Product Overview

The JIKONG V19 Smart Battery Management System (BMS) is designed for large-capacity series lithium battery packs. It integrates essential functions such as voltage acquisition, high-current active balancing, overcharge, over-discharge, overcurrent, and over-temperature protection, along with coulomb metering, Bluetooth communication, and host computer monitoring capabilities. This BMS is suitable for lithium iron phosphate (LiFePO4), ternary lithium (Li-ion), and lithium titanate (LTO) battery types.

The protection board utilizes energy transfer active balancing technology, achieving a maximum continuous balance current of 1A/2A. This high-current active equalization technology ensures battery consistency, extends battery range, and delays battery aging. It features a mobile APP for Android and iOS, allowing users to monitor battery status, modify parameters, and control charge/discharge switches via Bluetooth. The compact design, ease of operation, and comprehensive functions make it ideal for high-power energy storage, base station backup power, and solar power station battery packs.

2. Key Features

  • LED Bluetooth status indicator
  • APP Bluetooth remote operation
  • Battery capacity calculation
  • Supports PC operations
  • High precision voltage acquisition (±3mV)
  • High precision current acquisition
  • Support information screen display
  • Accurate time logging
  • Support RS485 communication
  • Support CAN communication
  • Support heating function
  • Alarm dry contact function
  • Discharge precharge function
  • Charge overcurrent protection
  • Charge overvoltage protection
  • Charge over temperature protection
  • Low temperature protection during charge
  • Discharge overcurrent protection
  • Discharge undervoltage protection
  • Discharge over temperature protection
  • Short circuit protection
  • Battery parallel current limiting function
JIKONG V19 JK-PB2A16S20P Smart BMS overview

Image description: JIKONG V19 JK-PB2A16S20P Smart BMS highlighting key specifications like 8S-16S, 200A charge/discharge, 2A balancing current, and support for Li-ion/Lifepo4/LTO battery types.

3. Specifications

3.1. General Parameters

Serial NumberProjectArgumentUnit
1Supply voltage20-70V
2Standby power consumption12mW
3Operating power consumption1100mW
4Operating temperature-30-70°C
5Maximum number of collection strings16S
6Maximum balancing current2A
7Maximum charging current10P: 100, 15P: 150, 20P: 200A
8Maximum discharge current10P: 100, 15P: 150, 20P: 200A
9Maximum instantaneous current10P: 200, 15P: 300, 20P: 400A
10Maximum internal loop resistance10P: 1, 15P: 0.45, 20P: 0.35mΩ
11Protective plate size300*100*24mm
12Finished weight1000g

3.2. Default Parameters

ParameterLi-ion DefaultLiFePO4 DefaultLTO DefaultUnit
Balancing initial voltage332V
Maximum balancing current222A
Unit overcharge voltage4.23.62.7V
Single overcharge protection recovery4.173.542.64V
Monomer undervoltage protection2.822.61.8V
Single undervoltage protection recovery2.852.651.85V
Automatic shutdown voltage2.82.51.7V
SOC-0% voltage2.92.61.85V
SOC-100% voltage4.183.52.65V
Trigger balancing differential pressure0.010.010.01V
Charging overcurrent protection delay333S
Charge overcurrent protection release time606060S
Discharge overcurrent protection delay300300300S
Discharge overcurrent protection release time606060S
Short-circuit protection delay555uS
Short circuit protection release time303030S
Charging overtemperature protection temperature707070°C
Charge overtemperature restore temperature606060°C
Discharge overtemperature protection temperature707070°C
Discharge overtemperature recovery temperature606060°C
Charging low temperature protection temperature-20-20-20°C
Charge low temperature to restore temperature-10-10-10°C
MOS Overtemperature protection temperature100100100°C
MOS Overtemperature protection recovery temperature808080°C
Device address000/
Discharge precharge time555S

3.3. Product Dimensions

The dimensions of the JK-PB1/2A16S-10/15/20P series protection board are 300mm × 100mm × 24mm. Refer to the diagram below for detailed measurements.

JIKONG BMS Product Dimensions

Image description: Diagram showing the dimensions of the JK-PB1/2A16S-10/15/20P series protection board, measuring 300mm x 100mm x 24mm.

4. Installation and Wiring

4.1. Safety Precautions

  • Ensure all connections are secure and correct before powering on the BMS.
  • Verify that the balance cables are properly connected.
  • Confirm that the P- and B- connections are correct.
  • Securely fix the protection board to the battery pack to prevent movement or damage.
  • Incorrect wiring or loose connections can lead to abnormal operation or severe damage.

4.2. Wiring Method

The JK-PB1/2A16S-10/15/20P series protection board is suitable for 7-16 series lithium battery packs. The specific wiring method varies depending on the number of cells in the battery pack. Always refer to the detailed wiring diagrams provided.

JIKONG BMS Wiring Diagram

Image description: Wiring diagram for the JIKONG BMS, showing connections for 16-string and 8-string cells, including B+, P-, charger, inverter, and display/switch connections. Note: There are two B8 cables; only the first B8 line needs to be connected. The second B8 cable does not need to be connected.

4.3. Interface Definitions

The BMS features various connectors for different functionalities. Understanding these interfaces is crucial for proper installation and operation.

Main Board Connectors (P1-P11)

ConnectorInterface NamePin NumberNameDefinition
P1Interface board interfaceConnects to the interface board
P4URAT display interface1K-Activation signal negative electrode
2K+Activate the positive signal
3GNDNegative terminal
4RXUART RX, 5V
5TXUART TX, 5V
6VCCDisplay power output
P5Display interface1VCCDisplay power output
2ADisplay RS485-A (negative signal)
3BDisplay RS485-B (positive signal)
4GNDNegative terminal
5K+Activation signal positive electrode
6K-Activation signal negative electrode
P6Acquisition interface1NT1Connect NTC1 temperature probe
2GNDConnect NTC1 temperature probe
3B0Total negative battery
4B1The first battery positive
5B2The second battery positive
6B3The third battery positive
7B4The fourth battery positive
P7Acquisition interface (Blue)1NTC2Connect NTC2 temperature probe
2GNDConnect NTC2 temperature probe
P8Acquisition interface (Red)1NT3Connect NTC3 temperature probe
2GNDConnect NTC3 temperature probe
3B8Reserved pin
4B9The ninth battery positive
5B10The tenth battery positive
6B11The eleventh battery positive
7B12The twelfth battery positive
P9Acquisition interface (Yellow)1NT4Connect NTC4 temperature probe
2GNDConnect NTC4 temperature probe
3B13The thirteenth battery positive
4B14The fourteenth battery positive
5B15The fifteenth battery positive
6B16The sixteenth battery positive
P10Heating interface (M3 screw)1HT-Heater element negative electrode
P11Power input (M3 screw)1B+The power input is positive
D1Bluetooth connection indicatorSteady on when connected, blinking when disconnected.
P-Connect to external load or negative terminal of charger (M6 screw)
B-Connect to the negative battery terminal (M6 screw)

Interface Board Connectors

The interface board provides additional connectivity for communication and control.

JIKONG BMS Interface Board Diagram

Image description: Detailed diagram of the BMS interface board, showing various ports like RS485, CAN, UART, RS232, and the dial switch for address setting.

InterfacePin NumberPin DefinitionRemark
Dry Contact1COM1
2S1
3COM2
4S2
CAN and RS485-11, 8RS485-B1
2, 7RS485-A1
3, 6GND
4CANH
5CANL
7GND
RS485-21RS485-B2
2RS485-A2
3GND
4NC

5. Operation

5.1. Device Activation

The BMS does not have a power-on control switch. It is designed for charging activation. After the battery assembly is complete, connect a charger (with voltage 2V higher than battery voltage) to activate the BMS. Alternatively, if you have a display screen or button, simply insert the cable into the display interface and press the button to activate.

5.2. Active Equalization

The BMS uses active equalization to transfer energy from high-voltage cells to low-voltage cells. Users can set the balance trigger pressure difference (mV) in the APP. When the difference between any two battery strings exceeds this value, balancing automatically activates. The default balance current is 1A/2A, adjustable via the APP based on battery capacity. The balancing function can be disabled via the APP if not needed.

5.3. Heating Function

The BMS includes a heating function to warm the battery at low temperatures, preventing charging/discharging issues due to reduced battery activity. The heating current is 10A. Users can control this function via the APP. It is recommended to install a normally closed temperature switch (45°C to 65°C) in series with the heating circuit as a secondary protection against thermal runaway.

5.4. Dry Contact Function

Two dry contacts are provided to control external devices like alarms or fans. When the BMS detects over-temperature, overcharge, or over-discharge, the dry contact can trigger an alarm or activate cooling fans. Users can select two trigger conditions via the APP and configure them as needed.

Dry Contact Wiring Diagram

Image description: Diagram illustrating the wiring principle for connecting a dry contact to external alarm equipment, showing a buzzer and DC power supply.

5.5. Discharge Precharge Function

The BMS includes a discharge pre-charging function with a default time of 5 seconds. This function can be enabled or disabled via the APP. Setting the precharge time to 0 disables the function.

5.6. Communication Function (Parallel Operation)

The BMS supports CAN and RS485 communications. The default CAN communication rate is 250K. Users can select the appropriate protocol in the APP based on their inverter brand and specifications. Two RS485 communication interfaces are available: RS485-1 for communication with inverters and other settings, and RS485-2 for connecting battery packs in parallel and communicating with a host computer. The default baud rate for RS485-2 is 115200. The BMS address (0-15) can be set using a DIP switch for parallel operation, with address 0 typically being the host.

JIKONG BMS Parallel Connection Diagram

Image description: Diagram showing multiple JIKONG BMS units connected in parallel for monitoring via a host computer, illustrating the RS485-2 daisy-chain connection.

5.7. APP and PC Software Operation

The JIKONG BMS can be monitored and configured using a mobile application (Android 7+ and iOS) or PC software. Download the mobile APP by scanning the QR code below. The APP and PC software provide multi-screen displays for real-time data, settings, and fault logging.

JIKONG BMS APP QR Code

Image description: QR code for downloading the JIKONG BMS mobile application, compatible with Android (version 7 minimum) and iOS.

JIKONG BMS APP and PC Software Interfaces

Image description: Screenshots of the JIKONG BMS mobile app and PC software, demonstrating multi-screen display and data connection for monitoring battery parameters like voltage, current, temperature, and SOC.

6. Protection Functions and Troubleshooting

The JIKONG BMS is equipped with multiple protection mechanisms to ensure battery safety and longevity. These protections are configurable via the APP or PC software.

6.1. Overcharge Protection

The BMS protects against overcharging by monitoring individual cell voltages. If any cell voltage exceeds the set overcharge protection voltage, the BMS will stop charging. Charging resumes when all cell voltages drop below the overcharge recovery voltage.

6.2. Undervoltage Protection

To prevent over-discharge, the BMS monitors cell voltages during discharge. If any cell voltage falls below the undervoltage protection threshold, the BMS will stop discharging. Discharge resumes when all cell voltages rise above the undervoltage recovery voltage. The BMS also features an automatic shutdown voltage, below which it will shut down completely to protect the cells.

6.3. Overcurrent Protection (Charge/Discharge)

The BMS provides protection against excessive charging and discharging currents. Users can set continuous current limits, overcurrent delay times, and recovery times via the APP. If the current exceeds the set limit for the specified delay, the BMS will interrupt the operation. It will resume after the recovery time.

6.4. Overtemperature Protection

The BMS monitors battery temperature during both charging and discharging. If the temperature exceeds the set over-temperature protection value, the BMS will stop the respective operation. It will resume when the temperature drops below the recovery threshold.

6.5. Low Temperature Protection

During charging, the BMS protects against low temperatures. If the battery temperature falls below the set low-temperature protection value, charging will stop. Charging resumes when the temperature rises above the recovery threshold. For extremely cold environments, using the heating function is recommended.

6.6. Short Circuit Protection

The BMS includes short-circuit protection. While the trigger current is not user-configurable, users can adjust the short-circuit protection delay and recovery time via the APP. If a short circuit occurs, the BMS will interrupt the circuit and resume operation after the recovery time. Adjusting the delay can help prevent false triggers from high inrush currents during initial connection to loads or chargers.

6.7. Emergency Switch

An emergency switch function is available. If issues like over-temperature, over-discharge, over-charge, or cell string drops occur during normal use, activating the emergency switch via the APP will enable charge and discharge for 30 minutes. This provides a temporary operational window, even if a single cell reaches automatic shutdown voltage, to prevent critical situations.

6.8. Intelligent Sleep

The intelligent sleep function allows the BMS to enter a low-power state when idle (charging/discharging current less than 1A for 26 consecutive hours) to reduce self-consumption. The BMS can be reactivated by pressing a button or connecting a charger.6.9. Charge Current Limiting

The BMS features a charge current limiting function. If the battery is overcurrent during charging, this function activates, limiting the charging current to approximately 10A to protect the battery.

6.10. LED Indicators

The interface board includes LED indicators to provide visual feedback on the BMS status and remaining battery power.

StatusNormal, Alarm, or ProtectionON/OFF IndicatorRUNALML1L2L3L4L5L6Instructions
Power OffNormalOFF
BalanceNormalONFlickerOFFBased on battery display
ChargingNormalONFlickerOFFBased on battery display
ChargingOvercurrent, over temperature, over voltage, charging failureONFlickerFlickerBased on battery display
DischargeNormalONFlickerOFFBased on battery display
DischargeOvercurrent, over temperature, under voltage, discharge failureONFlickerFlickerBased on battery display
Other alarmPassword not changed, short circuit, temperatureONFlickerFlickerBased on battery display

7. Maintenance

  • Regularly check all wiring connections for tightness and corrosion.
  • Keep the BMS clean and free from dust and moisture.
  • Monitor battery parameters via the APP or PC software for any unusual readings.
  • Ensure proper ventilation around the BMS to prevent overheating.
  • If the heating function is used, periodically inspect the heating elements and temperature switch.
  • Refer to the APP for parameter settings and adjust as needed based on battery health and environmental conditions.

8. User Tips

  • For optimal performance, ensure your battery pack is well-matched to the BMS's string count and current capabilities.
  • Utilize the mobile APP for real-time monitoring and fine-tuning of protection parameters to suit your specific battery chemistry and usage patterns.
  • When setting up parallel BMS systems, carefully configure the address dial switches to ensure proper communication between units and the host computer.
  • In cold climates, enable the heating function to maintain battery efficiency and prevent damage.

9. Packing List

The following items are included in your JIKONG V19 JK-PB2A16S20P Smart BMS package:

JIKONG BMS Packing List

Image description: Visual representation of the JIKONG BMS packing list, including the BMS unit, interface board, various adapter cables, network cable, sampling lines, switch, and heating adapter cable.

No.NameModelQuantity
1Interface boardJK-CN-Link1
2M6 screwM6*104
3Interface adapter cableHY2.0-XH2.54-22AWG-30CM1
4Interface adapter cable2XH2.54-22AWG-30CM1
5Interface adapter cableIDC2.54mm-20P-30CM1
6Dry contact terminalWJ15EDGK-3.81-4P1
7RJ45 network cableCAT5E-8P twisted pair-40CM1
8Balance sampling cableHY2.0-7P-22AWG-90CM-11
9Balance sampling cableHY2.0-6P-Blue casing-22AWG-90CM-21
10Balance sampling cableHY2.0-7P-Red casing-22AWG-90CM-31
11Balance sampling cableHY2.0-6P-Yellow casing-22AWG-90CM-41
12Device activation switchGH1.25-6P-50CM terminal wire1
13Energy storage board power cable18AWG-Red-50CM +M3 copper nose1
14Heating wireOT2.5-3-14AWG-150MM-Double head1

10. Support and Documentation

For detailed technical support, advanced troubleshooting guides, and the complete product specification, please refer to the official user manual PDF: JIKONG BMS User Manual (PDF).

For further assistance, please contact JIKONG customer service.

JIKONG Smart BMS Store

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.