1. Introduction
These replacement filters are designed to maintain the optimal cleaning performance of your compatible vacuum cleaner robot. Made from high-quality materials, they efficiently capture dust, large particles, and other airborne allergens, contributing to cleaner air in your home and extending the service life of your vacuum cleaner.
Image: Two complete filter units, ready for installation.
2. Compatibility
These filters (replacement number CP0663) are compatible with the following vacuum cleaner robot models:
- Medion MD 19500
- Medion MD 19510
- Medion MD 19511
- Medion MD 19900
- Philips FC6812, FC6812/01 (SpeedPro Max)
- Philips FC6813, FC6813/01 (SpeedPro Max)
- Philips FC6814 (SpeedPro Max)
- Philips FC6822, FC6822/01 (SpeedPro Max)
- Philips FC6823/01 (SpeedPro Max)
- Philips FC6826, FC6826/01 (SpeedPro Max)
- Philips FC6901/01 (SpeedPro Max Aqua)
- Philips FC6902/01 (SpeedPro Max Aqua)
- Philips FC6903/01 (SpeedPro Max Aqua)
- Philips FC6904/01 (SpeedPro Max Aqua)
- Philips XC8043
- Philips XC8047
- Philips XC8049
- Philips XC8147
- Philips FC6827
- Philips FC6908
3. Package Contents
Each package typically includes:
- 2 x Filter Units
- 2 x Sponge Filters
Image: Package contents showing filter units with foam and filter layers.
4. Installation (Filter Replacement)
To replace the filters in your vacuum cleaner robot, follow these general steps. Refer to your vacuum cleaner's specific user manual for detailed instructions on accessing the filter compartment.
- **Power Off**: Ensure your vacuum cleaner robot is powered off and unplugged (if applicable) before beginning.
- **Locate Filter Compartment**: Identify the filter compartment on your vacuum cleaner robot. This is typically located within the dustbin or a dedicated access panel.
- **Remove Old Filters**: Carefully remove the old filter unit and any separate sponge filters. Dispose of them properly.
- **Insert New Filters**: Place the new sponge filter into its designated slot, followed by the main filter unit. Ensure they are seated correctly and securely. The filter unit consists of a plastic frame, a white filter layer, and a black carbon cotton layer.
Image: Disassembled filter showing the foam and filter layers.
- **Close Compartment**: Close the filter compartment or dustbin securely.
- **Test**: Power on your vacuum cleaner robot and perform a short test run to ensure everything is functioning correctly.
5. Maintenance
Regular maintenance of your filters is crucial for optimal performance and longevity of your vacuum cleaner robot.
- **Regular Cleaning**: Gently tap the filter unit over a trash can to remove loose dust and debris. You can also use a soft brush or a handheld vacuum on a low setting to clean the filter surface.
- **Do Not Wash**: These filters are generally not washable. Washing them can damage the filter material and reduce their effectiveness.
- **Inspect for Damage**: Periodically inspect the filters for any signs of damage, tears, or excessive wear.
Image: Top view of a filter unit with the black foam layer.
6. Recommended Replacement Schedule
For best performance, it is recommended to replace your vacuum cleaner robot filters every 3 to 6 months, depending on usage frequency and household environment (e.g., presence of pets, allergies). A clogged or dirty filter can significantly reduce suction power and air quality.
Image: Bottom view of a filter unit showing the white filter layer.
7. Troubleshooting (Filter-Related)
| Problem | Possible Cause | Solution |
|---|---|---|
| Reduced Suction Power | Clogged or dirty filter. | Clean or replace the filter. Ensure it is installed correctly. |
| Unusual Odor from Vacuum | Dirty filter retaining odors. | Replace the filter. Ensure the dustbin is also clean. |
| Dust Escaping Vacuum | Filter not installed correctly or damaged. | Check filter installation. Replace if damaged. |
8. Specifications
- **Replacement Part Number**: CP0663
- **Material**: ABS Plastic frame, Carbon Cotton, Filter Media
- **Color**: As pictured (typically orange frame with black foam and white filter media)
- **Dimensions (Approximate)**:
- Length: 137 mm
- Width: 98 mm
- Height: 18 mm
Image: Filter dimensions.
9. User Tips
- Always ensure the filter is completely dry before re-installing it into the vacuum cleaner robot.
- For households with pets or allergy sufferers, consider more frequent filter checks and replacements.
- Keep spare filters on hand to ensure continuous optimal performance of your vacuum cleaner.
10. Warranty and Support
For any questions regarding the compatibility, installation, or performance of these filters, please contact the seller or manufacturer. Keep your purchase receipt for any warranty claims.
