1. Product Overview
The DykbRadio IP2363 30W Automatic Buck-Boost PD Fast Charging Module is a compact and efficient solution for charging 2S-5S Li-ion (NMC/NCA) or LiFePO4 battery packs. It supports a wide input voltage range (5-20V) from PD/QC power supplies or direct DC sources, automatically adjusting its output to charge batteries at up to 30W. The module features a toggle switch for battery cell count configuration, LED status indicators, and comprehensive protection features, ensuring reliable and safe operation.
Key Features:
- 30W Max Power: Requires 20V input for full output.
- Wide Input Range: 5-20V (PD/QC/DC).
- Battery Support: 2S-5S Li-ion / LiFePO4.
- Auto Buck-Boost: Steps up or down voltage as needed.
- Toggle Switch: Easy cell count and chemistry configuration.
- LED Status: Charging / Full / Fault indication.
- Smart Protection: Overvoltage protection (OVP), timeout, reverse polarity.
- Compact Size: 4.6 × 3.8 cm.
2. Safety & Warnings
Read all instructions before use to ensure safety and prevent damage.
⚠ DANGER: LITHIUM BATTERY SAFETY – Risk of fire or explosion.
Lithium batteries can be dangerous if mishandled. Use only with 2S-5S Li-ion or LiFePO4 battery packs that are in good condition. Do not use with damaged, swollen, or over-discharged batteries. Always double-check battery polarity before connecting to prevent module damage and fire.
⚠ CRITICAL: Toggle switch must match the battery configuration.
The module must be configured via the toggle switch to match your battery pack's cell count (2S-5S) and chemistry (Li-ion / LiFePO4). Incorrect settings will overcharge or undercharge the battery, causing permanent damage or fire.
⚠ CAUTION: Use 20V input to achieve full 30W output.
To achieve the maximum 30W charging power, you must use a 20V PD-compliant power supply. Lower input voltages will result in reduced charging power.
Electrical Safety:
- Input voltage: 5-20V (PD/QC or direct DC).
- Maximum output: 30W (requires 20V input).
- Battery compatibility: Li-ion: 4.2V-12.6V (2S-5S) / LiFePO4: 3.6V-18V (2S-5S).
- Power modes: 20W / 30W (default 30W).
- Observe correct battery polarity (+ / -) – reverse connection will damage the module.
- Use thick output cables (e.g., 18AWG) to avoid power loss.
- Do not short-circuit the battery output terminals.
- Keep the module away from water, moisture, and conductive debris.
- Ensure adequate ventilation – the module may generate heat during charging.
Handling Precautions:
- This module contains ESD-sensitive components. Use proper ESD precautions during handling.
- Handle the PCB by the edges to avoid damaging components.
- Do not bend or flex the PCB – it may crack solder joints.
- Do not operate the module in explosive or flammable atmospheres.
3. Setup & Connection
Follow these steps to set up and connect your IP2363 charging module:
- Configure the Module: Before connecting the battery, set the toggle switch to match your battery pack.
- Select the correct cell count (2S, 3S, 4S, or 5S).
- Select the correct chemistry (Li-ion or LiFePO4).
Note: Incorrect configuration will overcharge or undercharge the battery – verify carefully!

Image: IP2363 module showing the toggle switches for configuring cell count (2S, 3S, 4S, 5S) and battery chemistry (Li-ion/LiFePO4).
- Connect Battery: Connect your battery pack to the B+ and B- terminals, observing correct polarity. Double-check polarity - reverse connection will damage the module.
- Connect Power: Connect a PD/QC power supply or direct DC source (5-20V) to the input terminals. For maximum 30W output, use a 20V PD-compliant power supply.
- Monitor LEDs: Observe the LED status indicators to confirm charging progress.
Power Mode Selection:
- The module supports two power modes: 20W and 30W.
- Default setting is 30W (requires 20V input).
- To switch to 20W mode, refer to the configuration instructions on the PCB (PSET resistor values).

Image: Back of the IP2363 module, detailing PSET resistor configurations for Ternary Li-ion (4.2V) and Lithium Iron Phosphate (3.65V) batteries, along with corresponding power settings (20W/30W).
PSET Resistor Configuration:
- Ternary Li-ion (4.2V) Default:
- 9.1K = 4S, 13K = 30W (default)
- 6.2K = 3S, 6.2K = 20W
- Lithium Iron Phosphate (3.65V) LiFePO4:
- 9.1K = 30W
- 3.6K = 20W
4. Operating Instructions
LED Status Indicators:
- Flashing: Charging in progress.
- Solid On: Battery fully charged.
- Rapid Blinking: Input overvoltage or timeout fault.
Video: IP2363 Module in Operation
Video: Demonstration of the IP2363 module charging a battery pack, showing the LED indicator and USB-C connection.
For Optimal Performance:
- Use a 20V PD-compliant power supply to achieve the full 30W charging power.
- Ensure output cables are thick enough (e.g., 18AWG) to minimize power loss.
- Use high-quality PD/QC chargers for reliable performance.
- Charging power will taper near the full charge state - this is normal behavior.
Applications:
- 2S-5S Li-ion / LiFePO4 battery pack charging.
- Portable power station battery management.
- DIY battery projects.
- RC model battery charging (drones, cars, boats).
- E-bike and power tool battery charging.
5. Maintenance & Storage
Cleaning:
- Disconnect all power before cleaning.
- Use a soft, dry brush or compressed air to remove dust.
- Do not use water, solvents, or wet cleaning methods.
Storage:
- Store in a dry, dust-free environment at room temperature (15°C – 35°C).
- Avoid direct sunlight, high humidity, and corrosive atmospheres.
- If not used for an extended period, store in an anti-static bag.
- Before re-use, inspect the terminals for corrosion or damage.
Handling:
- Avoid dropping or mechanical stressing the module.
- Protect the input and output terminals from damage.
6. Troubleshooting
- No Charging / Insufficient Power Output:
- Ensure a 20V PD-compliant power supply is used for full 30W output. Lower input voltages will reduce charging power.
- Check output wire gauge; ensure wires are thick enough (e.g., 18AWG) to handle current and minimize power loss.
- Verify input power meets PD/QC standards.
- Confirm correct battery polarity. Reverse connection will damage the module.
- Check LED status indicators for fault conditions (rapid blinking).
- Module Overheating:
- Ensure adequate ventilation around the module.
- Avoid operating in enclosed spaces without airflow.
- If using high input voltage (e.g., 29.5V as reported by a user), monitor temperature closely. Consider reducing input voltage if excessive heat is generated, especially in enclosed setups.
- Incorrect Battery Charging:
- Double-check the toggle switch configuration for correct cell count (2S-5S) and chemistry (Li-ion / LiFePO4). Incorrect settings can lead to overcharge or undercharge.
- If switching from LiFePO4 to Li-ion, ensure the resistor is correctly replaced as per the PSET configuration.
7. User Tips
- Resistor Modification for Li-ion: If your module is set to LiFePO4 by default and you need to charge Li-ion batteries, you may need to replace a resistor according to the PSET configuration on the PCB. Refer to the "Setup & Connection" section for details.
- Heat Management: When operating at higher voltages or power levels, the module's components (like the inductance) can get very hot. Ensure good ventilation, especially if integrating the module into an enclosure, to prevent overheating.
- Verify Settings: Always double-check your cell count and chemistry settings with the toggle switch before connecting batteries to prevent damage.
8. Technical Specifications
| Parameter | Specification |
|---|---|
| Product Type | Auto Buck-Boost PD Fast Charger Module |
| Controller IC | IP2363 |
| Input Voltage | 5-20V (PD/QC or direct DC) |
| Max Output Power | 30W (requires 20V input) |
| Power Modes | 20W / 30W (default: 30W) |
| Battery Support | 2S-5S Li-ion (4.2V-12.6V) / LiFePO4 (3.6V-18V) |
| Configuration | Toggle switch (cell count + chemistry) |
| Protection Features | Overvoltage protection, timeout protection, reverse polarity protection |
| LED Indicators | Flashing = Charging / Solid = Full / Rapid Blink = Fault |
| Recommended Cable Gauge | ≥ 18AWG (for output to minimize power loss) |
| Dimensions | 4.6 x 3.8 cm |
| Operating Temperature | -20°C to +70°C |
| Certifications | CE, RoHS, WEEE Compliant |
9. Compliance & Disposal
Compliance Information:
This product complies with the essential requirements of applicable European Directives, including but not limited to:
- CE Marking: The product bears the CE mark in accordance with applicable EU harmonization legislation.
- RoHS Directive (2011/65/EU): This product is compliant with the Restriction of Hazardous Substances Directive.
- EMC Directive (2014/30/EU): This product meets electromagnetic compatibility requirements when installed properly.
CE Mark:
Disposal & Recycling (WEEE Directive):
This symbol (crossed-out wheeled bin) indicates that this product should not be treated as household waste. According to the WEEE Directive (2012/19/EU), it must be disposed of at an appropriate electronic waste collection point for recycling to prevent potential negative consequences for the environment and human health.
For proper disposal, please:
- Do not dispose of this product with general household waste.
- Take the product to a designated collection facility for electrical and electronic equipment.
- Follow local regulations for electronic waste disposal.
10. Warranty & Support
Each module is pre-tested for performance before shipping, and built-in smart protection ensures safe charging operation.
For technical support or inquiries, please contact the manufacturer:
- Manufacturer: Shenzhen yakaiyao Trading Co., Ltd.
- Manufacturer Address: 202, building s, No.1, 1st Road, Xiawei Industrial Zone Zhangkengjing community Guanhu Street Longhua District, Shenzhen
- Manufacturer Email/Tel: 1241273859@qq.com
EU Authorized Representative:
- Representative: MJCM SARL
- Address: 78 avenue des Champs Elysees Bureau 326 France
- Email: mjcm190928@gmail.com
Date of Issue: [Insert Date]
Version: 1.0