Estardyn 2.0 inch

Contents

Estardyn 2.0 Inch TFT LCD Display Module User Manual

Model: 2.0 inch | Driver IC: ST7789

1. Product Overview

The Estardyn 2.0 Inch Full Color TFT LCD Display Module is a compact and versatile display solution for various embedded projects, including those based on Arduino. It features a ST7789 controller, supporting both 4-wire SPI and 8-bit parallel interface modes, and offers a vibrant 240x320 pixel resolution.

Front and back view of the 2.0-inch TFT LCD module
Figure 1: Front and back view of the 2.0-inch TFT LCD module, highlighting pin headers and FPC connector.

2. Specifications

Feature Specification
Display Size 2.0 inches
Resolution 240x320 pixels
Driver IC ST7789
Interface Type 4-wire SPI / 8-bit Parallel Port
Display Color Full Color
Power Supply 2.8V ~ 3.3V
Screen Dimensions (mm) 34.6 x 47.8 x 2.03
Module Dimensions (mm) 37.5 x 58.04 x 6.5
Operating Temperature -20°C ~ 70°C
Display Technology COG (Chip-on-Glass)
Product parameters and dimensions
Figure 2: Detailed product parameters and dimensions.

3. Setup and Connections

This module can be connected via either a 4-wire SPI interface or an 8-bit parallel interface. For most microcontroller projects, especially with Arduino, the SPI interface is commonly used due to fewer required pins.

3.1 Pin Definitions

The module features an 8-pin interface. Refer to the table below for pin functions:

8-pin interface definition table
Figure 3: 8-pin interface definition and module dimensions.
PIN SYMBOL Description
1 GND Ground
2 VDD Power Supply (2.8V-3.3V)
3 SCL Serial Clock (SPI)
4 SDA Serial Data (SPI) / MOSI
5 RES Reset Pin
6 DC Data/Command Selection
7 CS Chip Select
8 BL Backlight Control

3.2 Basic SPI Connection (Example for Arduino)

When connecting to a microcontroller like an Arduino, ensure proper voltage levels. The display operates at 3.3V. If your microcontroller operates at 5V, use logic level shifters for data and control pins to prevent damage.

  • GND: Connect to your microcontroller's Ground (GND).
  • VDD: Connect to your microcontroller's 3.3V power supply.
  • SCL: Connect to your microcontroller's SPI Clock (SCK) pin.
  • SDA: Connect to your microcontroller's SPI Master Out Slave In (MOSI) pin.
  • RES: Connect to any available digital pin on your microcontroller.
  • DC: Connect to any available digital pin on your microcontroller.
  • CS: Connect to any available digital pin on your microcontroller.
  • BL: Connect to your microcontroller's 3.3V for constant backlight, or to a PWM-capable digital pin for brightness control.

4. Operating Instructions

To operate the display, you will need to write code for your microcontroller to communicate with the ST7789 driver IC. This typically involves:

  1. Initialization: Send a sequence of commands to the ST7789 controller to configure the display mode, orientation, and other settings.
  2. Drawing Graphics: Use specific commands to draw pixels, lines, rectangles, circles, and other shapes.
  3. Displaying Text: Implement or use a font library to render text on the screen.
  4. Image Display: Convert image data into a format compatible with the display and send it to the display memory.

Refer to the ST7789 datasheet and relevant programming libraries for detailed command sets and usage examples.

5. Maintenance

  • Cleaning: Use a soft, lint-free cloth to gently wipe the display surface. Avoid abrasive materials or harsh chemicals.
  • Handling: Always handle the module by its edges. Avoid touching the display area directly or applying excessive pressure.
  • Storage: Store the module in a dry, cool environment, away from direct sunlight, high humidity, and extreme temperatures.
  • ESD Protection: Take appropriate electrostatic discharge (ESD) precautions when handling the module to prevent damage to sensitive electronic components.

6. Troubleshooting

  • No Display / Blank Screen:
    • Verify that the VDD pin receives 2.8V-3.3V and GND is properly connected.
    • Ensure all data and control lines (SCL, SDA, RES, DC, CS, BL) are correctly wired and making good contact.
    • Check if the backlight (BL) pin is powered (e.g., connected to 3.3V).
    • Confirm that your initialization code for the ST7789 controller is correct and executed properly.
  • Garbled or Incorrect Colors:
    • Double-check that the interface mode configured in your software (SPI or parallel) matches your hardware connections.
    • Ensure the correct color mode (e.g., RGB565) is set in your display library or initialization code.
    • Inspect data lines for any shorts or open circuits.
  • Display Not Responding:
    • Verify the Reset (RES) pin is correctly toggled during the display initialization sequence.
    • Ensure the Chip Select (CS) pin is correctly asserted (usually low) during communication.
    • Check for any conflicts with other SPI devices if sharing the bus.

7. User Tips

  • Recommended Arduino Libraries: For Arduino users, the Adafruit GFX Library and the Adafruit ST7789 Library are highly recommended. These libraries provide robust functions for easy integration and programming of graphics and text.
  • Voltage Level Shifting: Always use logic level shifters if your microcontroller operates at 5V (e.g., Arduino Uno) to interface with this 3.3V display module. Direct connection can damage the display.
  • Backlight Control: The BL pin can be connected to a PWM (Pulse Width Modulation) pin on your microcontroller. This allows you to dynamically control the brightness of the display's backlight, saving power or adjusting for ambient light conditions.
  • Orientation: The ST7789 controller supports various display orientations. Experiment with the rotation settings in your library to find the best fit for your project.

8. Warranty and Support

For any technical assistance, support, or inquiries regarding your Estardyn 2.0 Inch TFT LCD Display Module, please contact the Estardyn Flagship Store. Refer to your purchase documentation or the seller's platform for specific contact information and support channels.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.