Estardyn TB6612 Dual Motor Driver Board

Contents

Estardyn TB6612 Dual Motor Driver Board Instruction Manual

Model: TB6612 Dual Motor Driver Board

1. Introduction

The Estardyn TB6612 Dual Motor Driver Board is a compact and efficient module designed to control up to two DC motors. It provides precise control over motor direction and speed, making it ideal for various microcontroller-based projects such as robotics, automation, and embedded systems. This manual provides essential information for setting up, operating, and maintaining your motor driver board.

2. Specifications

FeatureSpecification
ChipsetTB6612FNG
Logic Supply Voltage (VCC)2.7V - 5.5V DC
Motor Supply Voltage (VM)Up to 15V DC
Output Current (per channel)1.2A (average) / 3.2A (peak)
PWM FrequencyUp to 100kHz
Control ModesCW (Clockwise), CCW (Counter-Clockwise), Short-Brake, Stop
DimensionsApprox. 20mm x 20mm (0.8" x 0.8")
Package TypeSMD
Additional FeaturesStandby control, Built-in thermal shutdown, Low voltage detection, Filtering capacitors

3. Product Overview

The TB6612 Dual Motor Driver Board features the TB6612FNG chip, designed for efficient motor control. It includes all necessary components and decoupling capacitors for stable operation. All pins are broken out to standard 0.1" pitch headers for easy integration into breadboards or custom PCBs.

3.1 Pinout Diagram

Top and bottom view of the TB6612 Dual Motor Driver Board with pin labels
Figure 1: TB6612 Dual Motor Driver Board Pinout. The image displays the top and bottom views of the red PCB, highlighting the TB6612FNG chip and labeled pins for power, control, and motor outputs.

3.2 Pin Descriptions

  • VM: Motor Power Supply (up to 15V DC)
  • VCC: Logic Power Supply (2.7V - 5.5V DC)
  • GND: Ground
  • PWMA: PWM Input for Motor A (speed control)
  • AIN1, AIN2: Logic Inputs for Motor A (direction control)
  • STBY: Standby Pin (must be HIGH to enable motor driver)
  • BIN1, BIN2: Logic Inputs for Motor B (direction control)
  • PWMB: PWM Input for Motor B (speed control)
  • AO1, AO2: Motor A Outputs
  • BO1, BO2: Motor B Outputs

3.3 Dimensions

Top-down view of the TB6612 Dual Motor Driver Board with dimensions
Figure 2: Board Dimensions. This image shows the top view of the motor driver board with labels indicating its approximate dimensions of 20mm by 20mm.

4. Setup and Installation

Follow these steps to correctly set up your TB6612 Dual Motor Driver Board:

  1. Power Connections:
    • Connect your logic power supply (2.7V-5.5V DC) to the VCC pin.
    • Connect your motor power supply (up to 15V DC) to the VM pin.
    • Connect the ground of both power supplies to any of the GND pins on the board. Ensure common ground for your microcontroller and motor driver.
  2. Motor Connections:
    • Connect Motor A to the AO1 and AO2 pins.
    • Connect Motor B to the BO1 and BO2 pins.
  3. Control Signal Connections:
    • Connect your microcontroller's PWM output for Motor A to the PWMA pin.
    • Connect your microcontroller's digital outputs for Motor A direction to AIN1 and AIN2.
    • Connect your microcontroller's PWM output for Motor B to the PWMB pin.
    • Connect your microcontroller's digital outputs for Motor B direction to BIN1 and BIN2.
    • Connect a digital output from your microcontroller to the STBY pin. This pin must be pulled HIGH (e.g., 3.3V or 5V, matching VCC) to enable the motor driver. Pulling it LOW will put the driver into standby mode, saving power.

5. Operating Instructions

The TB6612FNG allows for flexible control of DC motors using a combination of logic inputs and PWM signals.

5.1 Enabling the Driver

Before any motor operation, ensure the STBY pin is set to HIGH. If STBY is LOW, the driver is in standby mode and motors will not respond.

5.2 Motor Direction Control

Motor direction is controlled by the logic states of the IN1/IN2 (for Motor A) and BIN1/BIN2 (for Motor B) pins. Refer to the table below for control modes:

IN1/BIN1IN2/BIN2ModeDescription
LOWLOWStopMotor stops, free-running
HIGHLOWCWMotor rotates Clockwise
LOWHIGHCCWMotor rotates Counter-Clockwise
HIGHHIGHShort-BrakeMotor brakes quickly

5.3 Motor Speed Control

Motor speed is controlled by applying a Pulse Width Modulation (PWM) signal to the PWMA (for Motor A) and PWMB (for Motor B) pins. The frequency of the PWM signal can be up to 100kHz. A higher duty cycle on the PWM signal will result in higher motor speed.

6. Maintenance

The TB6612 Dual Motor Driver Board is designed for durability and requires minimal maintenance. To ensure optimal performance and longevity:

  • Keep the board clean and free from dust and debris.
  • Avoid exposing the board to moisture or extreme temperatures.
  • Regularly check all connections to ensure they are secure and free from corrosion.
  • Ensure adequate ventilation if operating at higher currents or in enclosed spaces to prevent overheating.

7. Troubleshooting

If you encounter issues with your motor driver board, consider the following troubleshooting steps:

  • Motor Not Moving:
    • Verify that the STBY pin is pulled HIGH.
    • Check both VCC and VM power supplies for correct voltage and stable connection.
    • Ensure all GND connections are solid.
    • Confirm that the IN1/IN2 or BIN1/BIN2 pins are set to a valid direction mode (CW or CCW), not Stop or Short-Brake.
    • Check the PWMA/PWMB signal; ensure it is active and has a sufficient duty cycle.
    • Inspect motor connections for continuity and correct polarity.
  • Motor Behaves Erratically or Stops Unexpectedly:
    • Check for loose connections or intermittent contact.
    • Ensure power supplies are stable and can provide sufficient current for the motors. Voltage drops can cause erratic behavior.
    • The TB6612FNG has built-in thermal shutdown. If the chip becomes too hot due to excessive current or poor ventilation, it may temporarily shut down. Reduce load or improve cooling.
    • Low voltage detection can also cause unexpected stops. Ensure VM and VCC are within specified ranges.
  • Incorrect Motor Direction:
    • Review your logic for IN1/IN2 or BIN1/BIN2 pins. Swap the HIGH/LOW states to reverse direction, or reverse the motor's physical connections.

8. User Tips

While no specific user tips were available from external sources, here are some general best practices for working with motor drivers:

  • Start with Low Power: When testing a new setup, begin with lower motor voltages and currents to prevent damage in case of wiring errors.
  • Decoupling Capacitors: The board includes filtering capacitors, but for very noisy environments or long power leads, additional decoupling capacitors near the motor driver's power pins can improve stability.
  • Heat Management: Although the TB6612FNG has thermal shutdown, continuous operation at peak currents can generate significant heat. Consider adding a small heatsink if operating close to the 1.2A average current limit for extended periods.
  • Code Debugging: When troubleshooting, isolate the problem. First, verify your microcontroller code is generating the correct logic and PWM signals. Then, check the motor driver's response.

9. Support

For further assistance or inquiries regarding your Estardyn TB6612 Dual Motor Driver Board, please contact the seller or manufacturer directly. Ensure you have your product details and a clear description of the issue ready when seeking support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.