HORACO ZX-SW82TS-L2

Contents

HORACO 8 Port 2.5Gb L2 Managed Switch

Model: ZX-SW82TS-L2

User Manual

1. Introduction

This manual provides comprehensive instructions for the installation, configuration, and operation of the HORACO 8 Port 2.5Gb L2 Managed Switch. This device is designed to build high-security and high-performance networks, serving as an ideal convergence layer switch for office networks, campus networks, small and medium-sized enterprises, and branch offices.

The switch features 8x 2.5G RJ45 ports and 2x 10G SFP+ optical ports, offering stable and reliable data transmission. It supports advanced network management functions such as VLAN, LACP, DHCP, and SNMP, enabling efficient control and monitoring of your network infrastructure.

HORACO 8 Port 2.5Gb L2 Managed Switch front view

Figure 1: HORACO 8 Port 2.5Gb L2 Managed Switch with key features highlighted.

2. Safety Information

Please read and understand all safety instructions before installing or operating this device. Failure to follow these guidelines may result in injury, damage to the device, or property damage.

  • Ensure the power supply voltage matches the device's requirements.
  • Do not open the device casing. There are no user-serviceable parts inside.
  • Keep the device away from water, moisture, and high humidity environments.
  • Ensure proper ventilation to prevent overheating. Do not block cooling vents.
  • Avoid placing the device on unstable surfaces.
  • Protect power cables from being walked on or pinched.
  • In case of lightning, disconnect the power and network cables to prevent damage.
  • This device is designed for indoor use only.

3. Product Overview

The HORACO L2 Managed Switch is equipped with a variety of ports and indicators for efficient network operation and management.

3.1. Physical Features

Product Overview showing port counts

Figure 2: Product Overview with port types and counts.

  • 8x 2.5G RJ45 Ports: For high-speed Ethernet connections.
  • 2x 10G SFP+ Optical Ports: For high-bandwidth fiber optic uplinks.
  • 1x Console RJ45 Port: For command-line interface (CLI) management.

3.2. Port Description

Port Description diagram

Figure 3: Detailed port layout and labels.

  • Reset Button: Used to reset the device or restore factory settings.
  • Link/Act Indicators (per RJ45 port):
    • 2.5G Rate: Yellow Indicator (Always on), Green Indicator (Flashing).
    • 10M/100M/1G Rate: Green Indicator (Always on), Yellow Indicator (Not on).
  • Power LED: Indicates power status.
  • SYS LED: Indicates system status.
  • Ground Screw: For grounding the device.
  • DC 12V2A Power Supply Input: For connecting the power adapter.
8*2.5G Ports Link/Act indicator explanation

Figure 4: Explanation of Link/Act LED indicators for RJ45 ports.

4. Specifications

The following table details the technical specifications of the HORACO 8 Port 2.5Gb L2 Managed Switch.

Detailed Specifications table

Figure 5: Detailed technical specifications.

Table 1: Technical Specifications
AttributeValue
Brand NameHORACO
Model NumberZX-SW82TS-L2
Switch TypeEthernet, L2 Managed
Ports8x 100M/1G/2.5G RJ45 Network Ports, 2x 1G/2.5G/10G SFP+ Optical Ports, 1x Console RJ45 Port
Transmission Rate100Mbps/1G/2.5/10Gbps (2000 Mbps for RJ45 ports)
Switch Capacity80Gbps
Packet Forwarding Rate59.52Mpps
MAC Address Table16K
Buffer12 Mbit SRAM Packet Buffer
Forwarding ModeStore and forward
Communication ModeFull-Duplex & Half-Duplex
VLAN SupportYes (Supports 4K VLANs, 802.1Q-based VLAN, MAC-based VLAN)
FunctionLACP, VLAN Support, DHCP, SNMP, Port Mirroring, QoS, ACL, Spanning Tree, ERPS, EAPS, LLDP
Chip SolutionRealtek RTL9302D
InstallationDesktop
Lightning Protection6KV
Operating Temperature-10°C ~ 55°C
Storage Temperature-40°C ~ 75°C
Operating Humidity5% ~ 90% RH Non-condensing
Storage Humidity5% ~ 95% RH Non-condensing
Net Weight0.74KG
Gross Weight1.02KG
Product Dimensions230mm × 115mm × 33mm
Package Dimensions260mm × 220mm × 68mm
CertificationCE, FCC, RoHS
Product dimensions diagram

Figure 6: Product dimensions.

5. Setup and Installation

Follow these steps to properly install and connect your HORACO L2 Managed Switch.

5.1. Package Contents

Ensure all items are present in the package:

  • HORACO 8 Port 2.5Gb L2 Managed Switch
  • Power Adapter (US, EU, UK, or AU type, depending on selection)
  • User Manual (PDF available online)
Various power plug types

Figure 7: Available power plug types.

5.2. Physical Installation

  1. Placement: Place the switch on a stable, flat surface. Ensure adequate space around the device for proper ventilation. The metal shell design and cooling vents provide efficient heat dissipation.
  2. Grounding: Connect a grounding wire to the ground screw on the switch and to a proper earth ground.
  3. Power Connection: Connect the provided power adapter to the DC 12V2A input port on the switch, then plug the adapter into a suitable power outlet. The Power LED should illuminate.
  4. Network Connections:
    • Connect your network devices (PCs, NAS, Routers, 4K TVs) to the 8x 2.5G RJ45 ports using Ethernet cables.
    • For high-speed uplinks or connections to other fiber-enabled devices, insert SFP+ modules (not included) into the 2x 10G SFP+ optical ports and connect fiber optic cables.
  5. Console Connection (Optional): For initial configuration or advanced management via CLI, connect a console cable (not included) from your computer's serial port to the Console RJ45 port on the switch.
Highly Efficient Heat Dissipation with cooling vents

Figure 8: Cooling vents on the sides of the switch for efficient heat dissipation.

6. Operation: WEB Network Management

This switch supports WEB-based network management, allowing for easy configuration, monitoring, and troubleshooting. This section outlines how to access and use the WEB management interface.

For detailed information on each function, please refer to the full L2 Managed Ethernet WEB Network Management Operation Guide (PDF).

6.1. System Requirements for WEB Browsing

To access the WEB management interface, ensure your computer meets the following requirements:

Table 2: System Requirements for WEB Browsing
Hardware and SoftwareSystem Requirements
CPUPentium 586Up
Memory128MB or more
Resolution1024 x 768-up
ColorMore than 256 colors
BrowserInternet Explorer 8.0 or above, Firefox, Google Chrome, Opera, etc.
Operating SystemMicrosoft® Windows XP®/Vista®/7/8®, Linux, Unix, etc.

6.2. Login to WEB Browsing Session

Before logging in, ensure:

  • The switch has been configured for IP. By default, the interface IP address for VLAN 1 is 192.168.0.1.
  • The subnet mask is 255.255.255.0.
  • A host with a Web browser is connected to the network and can ping the switch.

To log in:

  1. Open a web browser and enter the switch's IP address (e.g., http://192.168.0.1) in the address bar.
  2. Press Enter. The Web login page will appear.
  3. Enter the default username admin. The default password is empty (leave blank).
  4. Click "Sign in".
WEB Login Page screenshot

Figure 9: WEB Login Page.

6.3. Basic Composition of WEB Page

The WEB page is composed of four main parts:

  • Banner Page: Displays the logo and real-time port status.
  • Category Navigation Page: Provides access to different function categories.
  • Menu Page: Displays the menu items for the selected category.
  • Main Page: Shows the content and configuration options for the selected menu item.
Basic Composition Page of Switch WEB Page screenshot

Figure 10: Basic Composition of the Switch WEB Page.

6.4. Common Page Buttons

The WEB interface includes several common buttons with standard functions:

Table 3: Common Page Button Functions
ButtonAction
RefreshUpdates all displayed information on the page.
ApplyApplies the updated values to the system's memory. Error checking is performed by the Web server upon clicking.
DeleteDeletes the current record or selection.
HelpOpens a help page with configuration instructions for the current section.

6.5. Error Messages and Entry Fields

If an error occurs during a WEB server request, an error message will be displayed in a dialog box.

Error Information Page screenshot

Figure 11: Example of an error message dialog box.

Some pages feature an entry field at the top, allowing you to select and edit specific entries. Selecting a value in this field displays its corresponding information on the page, making it the "active row" for editing.

Entry Field Page screenshot

Figure 12: Example of an entry field for selecting and editing records.

6.6. Detailed WEB Page Introduction

The WEB pages are organized into functional groups. Below is a summary of key configuration areas:

6.6.1. System Configuration

  • System Information: View product model, firmware version, MAC address, serial number, system uptime, and modify system clock.
  • IP Address Configuration: Configure the switch's IP address, subnet mask, and gateway. Management VLAN 1 is default and cannot be modified.
  • User Management: Configure user information. The default 'admin' user cannot be deleted, but its password can be modified.
  • Serial Port Information: View serial port settings like baud rate, character size, parity, stop bits, and flow control.
  • SNTP Configuration: Configure SNTP servers and time intervals for system clock synchronization.
  • SNMP Community Configuration: Configure SNMP community names and read/write permissions.
  • SNMP TRAP Configuration: Configure TRAP message recipients and parameters.
  • Log Information: View system logs based on priority levels.

6.6.2. Port Configuration

  • Port Basic Configuration: Enable/disable ports, set port rates, flow control, and view basic port information.
  • Port Statistics: View statistics such as sent/received packets and bytes, error packets, and discarded packets for all ports.
  • Port Storm Suppression: Configure suppression for broadcast, multicast, and DLF packets.
  • Port Speed Limit: Configure ingress and egress speed limits for ports.
  • Protection Port: Configure and display protection port information.
  • Port Mirroring: Configure port mirroring to monitor data packets.
  • Link Aggregation: Create and configure aggregation groups (LACP) to increase link bandwidth. Supports up to 32 aggregation groups, each with up to 8 ports.
Supports Link Aggregation diagram

Figure 13: Example of Link Aggregation setup.

6.6.3. PoE Configuration

  • PoE Port Configuration: Configure total PoE power, single-port power, and enable/disable PoE for individual ports.
  • PoE Scheduling Configuration: Schedule PoE power on/off based on time and day.
  • PD Query Configuration: Detect PD (Powered Device) online status, configure PD IP address, query interval, and timeout.

6.6.4. VLAN Configuration

  • VLAN Configuration Page: Create VLANs (VID 2-4094), view port membership (tagged/untagged). VLAN 1 is default and cannot be deleted.
  • Access Port Configuration: Configure ports in Access mode and assign them to a single VLAN.
  • Trunk Port Configuration: Configure ports in Trunk mode, allowing multiple tagged VLANs.
  • Hybrid Port Configuration: Configure ports in Hybrid mode, supporting both tagged and untagged VLANs.
  • GVRP Configuration: Enable GVRP globally and per port to dynamically register VLAN information.
Supports VLAN Segmentation diagram

Figure 14: VLAN Segmentation example with network access and devices.

6.6.5. Security Configuration

  • MAC Configuration:
    • Manual MAC Address Binding: Bind specific MAC addresses to ports.
    • Automatic MAC Address Binding: Convert dynamically learned MAC addresses to static bindings.
    • MAC Address Filtering: Configure filtering rules based on MAC addresses.
    • MAC Address Table: View the MAC address table.
  • ACL Configuration:
    • Standard IP Group ACL: Create rules based on source IP address.
    • Extended IP Group ACL: Create rules based on source/destination IP, protocol type, ports, and TCP flags.
    • MAC IP Group ACL: Create rules based on source MAC, source IP, and destination IP.
    • MAC ARP Group ACL: Create rules based on ARP operation type, sender MAC, and sender IP.
    • Port Apply ACLs: Apply configured ACL groups to specific ports.
    • ACL Configuration Information: View all configured ACL rules.
  • AAA Configuration:
    • AAA Global Configuration: Enable 802.1x, configure re-authentication, RADIUS server settings, and shared keys.
    • AAA Port Configuration: Configure authentication port mode and maximum supported hosts per port.
    • AAA User Information: View status of connected users.
  • Native Management Security Configuration: Control access to management services (TELNET, WEB, SNMP) and apply ACL filtering.

6.6.6. DHCP Configuration

  • DHCP Client: Configure the switch to obtain an IP address from a DHCP server.
  • DHCP Relay: Configure DHCP relay functionality.
  • DHCP Server: Configure the switch to act as a DHCP server, including address pools and interface settings.
  • DHCP Snooping: Configure global and interface-specific DHCP snooping settings to prevent unauthorized DHCP servers.

6.6.7. Multicast Configuration

  • IGMP SNOOPING Configuration: Enable IGMP Snooping, configure VLAN-specific settings, querier, and static mrouter ports.
  • CMRP Configuration: Configure global and port-specific CMRP settings.
  • Multicast Routing Configuration: Configure the switch for multicast routing.
  • IGMP Configuration: Configure IGMP parameters per interface, including query intervals and robustness variables.
  • PIM-SM Configuration: Configure global and interface-specific PIM-SM parameters for multicast routing.

6.6.8. Ring Network Configuration

  • Spanning Tree Configuration: Configure global Spanning Tree parameters (MSTP) and port-specific settings.
  • ERPS Configuration: Configure Ethernet Ring Protection Switching (ERPS) instances and rings for network redundancy.
  • EAPS Configuration: Configure Ethernet Automatic Protection Switching (EAPS) rings for network redundancy.

6.6.9. Advanced Configuration

  • QoS Configuration: Configure Quality of Service (QoS) application and scheduling, including port QoS type, user priority, and queue weights.
  • LLDP Configuration: Configure Link Layer Discovery Protocol (LLDP) globally and per port, and view neighbor information.

6.6.10. System Tools

  • Save Configuration: Save the current running configuration to the startup configuration file.
  • Backup Configuration: Download the current configuration file to your PC.
  • Restore Configuration: Upload a configuration file from your PC to the switch.
  • Software Upgrade: Upload firmware image files to upgrade the switch software.
  • Restore Factory Configuration: Delete the startup configuration file and restore the switch to factory default settings. The switch will restart automatically.
  • Restart: Reboot the switch.

7. Maintenance

Regular maintenance helps ensure the longevity and optimal performance of your switch.

  • Cleaning: Periodically clean the exterior of the switch with a soft, dry cloth. Do not use liquid or aerosol cleaners. Ensure cooling vents are free from dust and obstructions.
  • Firmware Updates: Check the manufacturer's website for the latest firmware updates. Regularly updating the firmware can improve performance, add new features, and fix bugs. Refer to the "Software Upgrade" section (6.6.10) for instructions.
  • Configuration Backup: Regularly back up your switch configuration to prevent data loss in case of unexpected issues. Refer to the "Backup Configuration" section (6.6.10).
  • Environmental Control: Ensure the operating environment remains within the specified temperature and humidity ranges to prevent hardware damage.

8. Troubleshooting

This section provides solutions to common issues you might encounter.

  • No Power:
    • Check if the power adapter is securely connected to the switch and the power outlet.
    • Verify the power outlet is functional.
    • Ensure the correct power adapter is being used.
  • No Link Light on Port:
    • Ensure the Ethernet cable is properly connected at both ends.
    • Check if the connected device is powered on and functioning correctly.
    • Try a different Ethernet cable or port.
    • Verify port settings in the WEB management interface (e.g., Port Basic Configuration, Port Storm Suppression, Port Speed Limit).
  • Cannot Access WEB Management Interface:
    • Verify your computer's IP address is in the same subnet as the switch (default 192.168.0.x, subnet 255.255.255.0).
    • Ensure there are no IP address conflicts on the network.
    • Try pinging the switch's IP address (default 192.168.0.1).
    • Clear your browser's cache or try a different browser.
    • If you changed the switch's IP address and forgot it, you may need to reset the switch to factory defaults (see "Restore Factory Configuration" in 6.6.10).
    • Check if the WEB service is enabled under Native Management Security Configuration (6.6.5).
  • Slow Network Performance:
    • Check port statistics for errors or discarded packets.
    • Ensure all devices are operating at their expected speeds (e.g., 2.5G devices connected to 2.5G ports).
    • Review QoS settings if configured, as they might prioritize certain traffic over others.
    • Check for network loops if Spanning Tree Protocol is not properly configured.
  • Forgot Login Password:
    • If the password for the 'admin' user was changed and forgotten, you will need to perform a factory reset to regain access using the default credentials.

9. User Tips

  • VLAN Configuration: The switch supports multiple VLANs per port (multi-VLAN support) and Link Aggregation (LACP). When configuring VLANs, you can assign multiple VLANs to a port using Trunk or Hybrid modes, allowing for flexible network segmentation and traffic management.
  • High-Speed Connections: Utilize the 2.5Gb RJ45 ports for connecting high-bandwidth devices like NAS, high-performance PCs, or 4K TVs to maximize local network speeds. The 10Gb SFP+ ports are ideal for server uplinks or connecting to other 10Gb network infrastructure.
  • Heat Dissipation: While the switch features efficient heat dissipation, ensure it is placed in a well-ventilated area, especially when operating under heavy load, to maintain optimal performance and device longevity.

10. Warranty and Support

HORACO provides a 1-year free warranty and lifetime professional technical support for this product. For warranty claims, technical assistance, or further inquiries, please contact your vendor or the official HORACO support channels.

Please retain your proof of purchase for warranty purposes.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.