JIKONG RS485 Adapter

Contents

JIKONG RS485 Adapter User Manual

Model: RS485 Adapter for JIKONG 4S-8S BMS

Brand: JIKONG

1. Overview

The JIKONG RS485 Adapter is an isolated USB to TTL module specifically designed for the GPS interface of JIKONG Battery Management Systems (BMS). This adapter facilitates convenient connection between the BMS and a host computer. It allows users to access internal BMS data, adjust parameters, and perform firmware updates, ensuring optimal system performance and management.

JIKONG RS485 Adapter product image

Figure 1: JIKONG RS485 Adapter

2. Features

  • Compatible with 5V and 3.3V TTL levels.
  • Equipped with a 1500VDC isolated power module for enhanced safety.
  • Features an LED status indicator for operational feedback.
  • Supports a maximum baud rate of 256000bps.
  • Designed for use with JIKONG Smart BMS, including LTO Battery BMS, Active Balanced BMS, and Common Port BMS.
  • Enables access to BMS functions such as Overcharge Protection, Over Discharge Protection, Overcurrent Protection, and Short Circuit Protection.

3. Setup and Connection

Follow these steps to connect the JIKONG RS485 Adapter to your BMS and computer:

  1. Connect to PC: Insert the USB end of the adapter into your computer's USB port. Verify that the CH340 driver is working correctly in Device Manager. The adapter should appear as "USB-SERIAL CH340 (COMx)", where 'x' is the assigned COM port number. If a warning sign (exclamation mark) appears, the driver may not be installed. Download the driver from the official website (e.g., https://www.wch.cn/download/CH341SER_EXE.html) and install it.

  2. Connect to BMS: Connect the other end of the adapter (the 4-pin connector) to the GPS interface on your BMS. Ensure the connection is secure and correctly oriented.

    JIKONG RS485 Adapter cable wiring diagram

    Figure 2: Adapter cable showing pinout. Yellow Cable = A, White Cable = B, Black Cable = GND.

    The pin definitions for the 4-pin connector are as follows:

    Pin Name Definition
    GND Connects to external device GND
    TX Transmit data pin, connects to external device RX
    RX Receive data pin, connects to external device TX
  3. BMS Power-On and Mobile App Settings: After powering on the BMS, use the mobile application to configure the BMS parameters. Set the device address to '1' and the serial port 1 protocol to '1'.

  4. Connect to Host Computer Software: Launch the host computer software. In the bottom right corner, enter the device address and the COM port number identified in step 1. Click 'Connect' to establish communication.

4. Operating Instructions (Host Computer Software)

The JIKONG BMS monitoring platform software provides various functionalities:

  • Real-time Status Page: This page displays real-time information such as battery voltage, charging current, abnormal alarms, battery status, and balancing group data.

    Host computer software real-time status dashboard

    Figure 3: Real-time status display in JIKONG BMS software.

  • Parameter Settings Page: By default, parameters cannot be modified. To make changes, you must click 'Authorize Settings' and enter the default factory password: 123456.

  • BMS Control Page: Similar to parameter settings, modifications on this page require authorization. Enter the default factory password: 123456.

  • System Log Page: Click the 'Update Log' button to refresh the BMS internal log to the host computer. The 'Export Log' button allows you to save all current log data to a specified folder on your computer in XLSX format, viewable with Excel or similar software.

  • Fault Download Page: The 'Fault Download' button updates the BMS internal fault log to the host computer. The 'Export Fault' button saves all displayed fault log data to a specified folder on your computer in XLSX format.

  • About BMS Page: This section provides basic product information, including the model, hardware version, software version, and power-on time.

  • Firmware Upgrade: To upgrade firmware, click the icon in the upper right corner of the host computer software, then select 'Upgrade Firmware'. Choose the appropriate firmware file to proceed with the upgrade.

  • Forced Firmware Upgrade: In cases where the device is bricked or requires a mandatory firmware change, use the 'Forced Upgrade' function. Select the forced upgrade firmware and click 'Forced Upgrade'. This process requires an authorization code from the original BMS manufacturer.

5. Maintenance

The JIKONG RS485 Adapter is a low-maintenance device. No specific routine maintenance is required. To ensure longevity and reliable performance, please observe the following:

  • Keep the adapter clean and free from dust and moisture.
  • Avoid exposing the adapter to extreme temperatures or direct sunlight.
  • Handle the cables and connectors with care to prevent damage.
  • Store the adapter in a dry, cool place when not in use.

6. Troubleshooting

If you encounter issues with the JIKONG RS485 Adapter, consider the following troubleshooting steps:

  1. Check Connections: Verify that all connections between the adapter, computer, and BMS are correct and secure.

  2. Verify CH340 Driver: Ensure that the CH340 driver is properly installed on your computer and recognized in Device Manager without any errors.

  3. Check BMS Settings: Use the mobile application to confirm that the BMS address and communication protocol settings are correctly configured.

  4. Software Communication: If the software fails to connect, double-check the selected COM port and device address in the host computer software.

7. Specifications

Attribute Value
Model RS485 Adapter
Compatibility JIKONG 4S-8S BMS
Cable Length 380mm
Module Dimensions (L x W x H) 53.00mm x 24.00mm x 14.00mm
TTL Level Compatibility 5V and 3.3V
Isolation 1500VDC Isolated Power Module
Max Baud Rate 256000bps
Interface USB to TTL (RS485)
Usage Scenario (BMS) Power BMS, Energy Storage BMS, 3C Digital BMS
Balance Function (BMS) Active Balanced BMS
Charge and Discharge Port (BMS) Common Port BMS
Type (BMS) LTO Battery BMS
Protection Functions (BMS) Overcharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection

8. User Tips

  • Always ensure the correct CH340 driver is installed and recognized by your operating system before attempting to connect the adapter.
  • For optimal performance, use the latest version of the JIKONG BMS host computer software and mobile application.
  • When performing firmware updates, ensure a stable power supply to both the computer and the BMS to prevent interruptions.

9. Warranty & Support

For warranty information, technical support, or service inquiries, please contact your original seller or the JIKONG manufacturer directly. Please refer to the official product documentation for detailed warranty terms and conditions.

A PDF version of the user manual is available for download: User manual (PDF)

© 2024 JIKONG. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.