Important Safety Information
Please read and understand all safety instructions before using this appliance. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- Always plug the heater directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
- Do not operate any heater with a damaged cord or plug, or after the heater malfunctions, has been dropped or damaged in any manner.
- Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and keep them away from the sides and rear.
- Do not use outdoors.
- This heater is not intended for use in bathrooms, laundry areas, and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.
- Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over.
- To disconnect heater, turn controls to OFF, then remove plug from outlet.
- Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
- To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
- A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable vapors or liquids are used or stored.
- Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
- Always unplug heater when not in use.
Integrated Safety Features:
- Overheat Protection: The heater is equipped with an automatic shut-off mechanism that activates if the unit reaches an unsafe temperature due to severe overheating.
- Tip-Over Protection: A safety switch automatically turns off the heater if it is accidentally tilted or knocked over (e.g., when dumped 113°F from its upright position).
- Built-in Overload Protector: This feature automatically shuts down the heater to prevent overheating.
- Safety Patented Design: Tail fin separation technology is incorporated to ensure safe heating without oil leakage.
Product Overview
The Zohop Oil Filled Radiator Heater is designed to provide efficient and consistent warmth for indoor spaces. Its portable design and multiple safety features make it a reliable heating solution.
Key Features:
- Powerful and Efficient Heating: 1500W power output, suitable for rooms up to 200 sq.ft. Oil-filled fins retain heat effectively for continuous warmth.
- Adjustable Heat Settings: Features three heat settings (Low, Medium, High) and an adjustable thermostat for personalized comfort.
- Whisper-Quiet Operation: Operates with minimal noise, ideal for quiet environments like bedrooms and offices.
- Portable Design: Equipped with four 360° swivel wheels for easy movement between rooms.
- Compact Body Design: Space-saving and aesthetically pleasing.
- Integrated Cord Storage: A built-in rack allows for neat storage of the power cord when not in use.
Package Contents
Ensure all items are present and in good condition upon unpacking.
- 1 x Radiator Heater
- 4 x Wheels
- 1 x User Manual
Specifications
| Feature | Detail |
|---|---|
| Model | NSC-150-7B2 |
| Voltage | 120V/60Hz |
| Rated Power | 1500W |
| Coverage Area | 15-20 sq.m / 200 sq.ft |
| Heating Element | Heating Tube |
| Heat Settings | 3 (Low, Medium, High) |
| Thermostat | Adjustable |
| Timer | No |
| Digital Display | No |
| Remote Control | No |
| Certification | FCC |
| Product Dimensions (L x W x H) | Approx. 13.8" x 9.8" x 24.4" (35 cm x 25 cm x 62 cm) |
| Weight | 7.5 lbs / 3.4 kg |
Setup and Assembly
Follow these steps to assemble and prepare your heater for use.
- Unpack: Carefully remove the heater and all components from the packaging. Retain packaging for future storage.
- Attach Wheels:
- Turn the heater upside down.
- Locate the wheel attachment points on the base of the heater.
- Insert each wheel into its designated slot until it clicks securely into place. Ensure all four wheels are firmly attached.
- Placement:
- Place the heater on a firm, level surface.
- Ensure there is at least 3 feet (0.9 m) of clear space around the heater from any walls, furniture, curtains, or other combustible materials.
- Do not place the heater directly below a power outlet.
Operating Instructions
Follow these steps to operate your oil-filled radiator heater.
- Plug In: Insert the power plug into a suitable 120V/60Hz wall outlet. The power indicator light on the control panel will illuminate.
- Adjust Thermostat: Turn the upper knob (thermostat control) to your desired temperature setting. Turning it clockwise increases the temperature.
- Select Heat Setting: Use the lower knob to select one of the three heat settings:
- OFF: Heater is off.
- I (Low): Provides a lower heat output.
- II (Medium): Provides a medium heat output.
- III (High): Provides the maximum heat output (1500W).
- Automatic Operation: Once the desired temperature is reached, the heater will cycle on and off to maintain the set temperature.
- To Turn Off: Turn the heat setting knob to "OFF" and unplug the heater from the wall outlet.
Maintenance
Proper maintenance ensures the longevity and efficient operation of your heater.
- Cleaning:
- Always unplug the heater and allow it to cool completely before cleaning.
- Wipe the exterior surfaces with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Ensure no water enters the interior of the heater.
- Storage:
- When not in use, store the heater in a cool, dry place.
- Utilize the built-in cord storage rack to neatly wrap the power cord, preventing tangles and damage.
Troubleshooting
If you encounter issues with your heater, refer to the following common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Heater does not turn on. | No power to the unit. Thermostat set too low. Tip-over switch activated. Overheat protection activated. | Check if the heater is securely plugged into a working outlet. Increase the thermostat setting. Ensure the heater is on a flat, stable surface. Unplug the heater, let it cool for 30 minutes, then plug it back in. |
| Heater is on but not producing enough heat. | Heat setting is too low. Room size exceeds coverage area. Drafts or poor insulation. | Increase the heat setting (I, II, or III). Ensure the heater is appropriate for the room size (up to 200 sq.ft.). Close windows/doors, improve room insulation. |
| Heater makes unusual noises. | Normal expansion/contraction of metal parts. Loose components. | Minor clicking sounds are normal during heating and cooling. If noises are loud or persistent, discontinue use and contact support. |
User Tips
Maximize your heater's performance and comfort with these helpful tips.
- Quiet Operation: The heater's low-noise design makes it ideal for use in bedrooms or offices where a quiet environment is preferred.
- Optimal Placement: For best results, place the heater in the center of the room or near the area you wish to heat most. Its 360° rotating wheels allow for easy repositioning.
- Energy Efficiency: To save energy, use the heater to supplement your main heating system in specific rooms rather than heating your entire home to a high temperature.
- Continuous Warmth: Oil-filled radiators provide a gentle, consistent heat that radiates evenly, avoiding the dry air often associated with forced-air heaters.
Warranty and Support
This product comes with a 1-year warranty from the date of purchase. For any questions, technical assistance, or warranty claims, please refer to the contact information provided at the point of purchase.
Please retain your proof of purchase for warranty purposes.