1. Introduction
The SpeedyBee F405 V5 OX32 55A Flight Controller (FC) and Electronic Speed Controller (ESC) Stack is a high-performance, all-in-one solution designed for model aircraft, particularly FPV drones and helicopters. This stack combines a powerful F405 V5 Flight Controller with an OX32 55A 4-in-1 ESC, offering advanced features such as wireless tuning, robust power architecture, and integrated protection mechanisms. It is engineered for precision and top performance in various flying styles.
2. Package Contents
2.1 Standard Package

Image: SpeedyBee F405 V5 OX32 55A Standard Package Contents
- SpeedyBee F405 V5 Model Aircraft Flight Controller x1
- SpeedyBee OX32 55A 32 4-in-1 Model Aircraft ESC x1
- Model Aircraft Stack Connector Cable x1 (SH1.0 10pin*25mm)
- Model Aircraft Stack Connector Cable x1 (SH1.0 10pin*75mm)
- DJI Air Unit Connector Cable x1 (SH1.0 6pin*80mm)
- GPS 6pin Connector Cable + 4pin SH1.0 Terminal x1 (SH1.0 6pin to SH1.0 4pin*120mm)
- Receiver 4pin Connector Cable x1 (SH1.0 4pin*100mm)
- XT60 Power Cable x1 (120mm)
- M3 Model Aircraft Stack Mounting Screws x4 (30mm)
- Quick Start Guide for Model Aircraft Stack x1
- M3 Hex Nylon Nuts x5
- M3 Black Silicone Washers x5
- Capacitor Heat Shrink Tube x2
- Model Aircraft FC Silicone Covers x5
- Model Aircraft ESC Silicone Covers x5
- 35V 1000uF Solid Capacitor x1
2.2 Deluxe Package (Includes all Standard items plus the following)

Image: SpeedyBee F405 V5 OX32 55A Deluxe Package Contents
- Soldering Practice Board x1
- Short-Circuit Protection Tool x1
- Type-C Extension Module 4pin Connector Cable x1 (SH1.0 4pin*80mm)
- Active Buzzer x1
- Type-C Extension Module x1
- Power Expansion Board x4
3. Specifications
3.1 SpeedyBee F405 V5 30.5×30.5mm Model Aircraft Flight Controller
| Feature | Description |
|---|---|
| MCU | STM32F405 |
| IMU (Gyro) | ICM42688P |
| USB Port Type | New Type-C interface |
| Barometer | SPA06-003 |
| OSD Chip | AT7456E |
| Full-featured Bluetooth Tuning | Supported. Connect via SpeedyBee App for FC firmware flashing and parameter tuning. |
| Wireless FC Firmware Upgrade | Supported |
| DJI Air Unit Connection | Supports 6-pin direct plug-in or solder connection |
| Blackbox | Supported, built-in 16MB storage chip |
| Input Voltage | 3-6S LiPo battery |
| Independent 5V BEC Output | 9 groups (4× +5V pads on front, 1× BZ+ buzzer pad, and 4× +5V pads at the corners for external LEDs). Total output current: 1.5A. |
| Independent 9V BEC Output | 2 groups (1x 9V pad on front, 1x 9V output in a connector on the back). Total output current: 3A. Supports PINIO remote on/off control. |
| MCU & Gyro Power | Independent LDO |
| 3.3V Output | 1 group (1× 3.3V pad on front) |
| 4.5V Output | 3 groups (3× 4.5V pads on front). Can power receiver and GPS when FC is powered via USB. Max output current: 1A. |
| ESC Signal | M1-M4 pads and 10-pin connector on the back |
| Servo Signal | S5-S6 pads on the front |
| ESC Telemetry Input | Supported (UART5) |
| Betaflight Camera Tuning Pad | Supported (CC pad on front) |
| I2C | Supported (GPS connector + pads) |
| UART | UART1 (Bluetooth); UART2 (front pads for receiver); UART3 (DJI VTX pads + rear SH1.0-6-pin); UART4 (GPS pads + front SH1.0-6-pin); UART5 (TLM); UART6 (receiver pads + rear SH1.0-4-pin) |
| ST LED Pads | Supported, on front G/5V/LED pads; controlled by FC firmware |
| Meteor LED Strip Pads | Supported. Switch between SB-LED and ST-LED modes via BOOT button or App. In SB-LED mode, controlled by ESP32 Bluetooth chip. |
| Buzzer Pads | Supported |
| BOOT Button | [A] Hold BOOT while powering on to force DFU mode for flashing. [B] When powered and in standby, short-press cycles LED display modes; long-press switches SB-LED/ST-LED. In ST-LED mode, LED1–LED4 are controlled by FC firmware. |
| RSSI Pads | Supported |
| SmartPort | Not supported |
| Supported FC Firmware | Betaflight, INAV, Ardupilot |
| Firmware Target Name | SPEEDYBEEF405V5 |
| Factory Firmware Version | Betaflight 4.5.2 |
| Configurator Version | Betaflight 10.10.0 |
| Mounting Holes | 30.5 × 30.5mm (Ø4mm), side opening |
| Dimensions | 39mm (L) × 39mm (W) × 4.9mm (H) |
| Weight | 8.1g |
3.2 SpeedyBee OX32 55A 30.5×30.5 4-in-1 ESC
| Feature | Description |
|---|---|
| Default Firmware | OX32 |
| Continuous Current | 55A (per channel) / 220A (4-in-1) |
| Maximum Current | 70A (per channel) / 280A (4-in-1) |
| TVS Protective Diode | Yes (built-in) |
| External Capacitor | 1000µF Solid Capacitor (included in package) |
| ESC/Motor Protocol | DSHOT300/600 |
| Input Voltage | 3-6S LiPo |
| Power Output | VBAT |
| Current Sensor | Supported |
| ESC Telemetry | Supported |
| Mounting Holes | 30.5 × 30.5mm (Ø4mm), side opening |
| Dimensions | 40.9mm (L) × 44.9mm (W) × 8.0mm (H) (incl. heatsink) |
| Weight | 19.1g |
| ESC Webpage | https://ox32.oxbot.com/ |
| Current Meter Note | Supported (Scale=27, Offset=-2644) |
4. Key Features
- Recessed Type-C USB Port: Efficiently prevents USB detachment under extreme conditions. A 2mm lower profile simplifies battery installation and maintenance.

Image: Recessed Type-C USB Port design for improved durability and ease of use.
- Equipped with OX32 Firmware: Preloaded with high-performance OX32 firmware for model aircraft ESCs, featuring an efficient DMA control algorithm for faster acceleration response, safe soft-start, and improved robustness. Key throttle ranges are optimized for better flight stability across different flying styles. Compatible with small-pitch propellers, enhancing flight stability and cornering performance.

Image: Overview of OX32 Firmware features and benefits.
- Onboard ICM-42688 Gyroscope: Features upgraded noise reduction with an independent high-PSRR LDO to effectively isolate power noise. Dedicated external clock input ensures more precise data output and provides temperature drift redundancy. (External clock function requires Betaflight 4.6.0 or later).

Image: Diagram highlighting the ICM-42688 Gyroscope and its noise reduction capabilities.
- Onboard Blackbox Storage Chip: Includes 16MB built-in Blackbox storage with multi-platform firmware support, ensuring readiness for use without compatibility issues.

Image: Illustration of the integrated 16MB Blackbox storage chip.
- Wireless Tuning 2.0: Enhanced functionality and improved performance. Features newly upgraded algorithm architecture, new APP wireless firmware update, and multicolor battery LED function. Allows full-featured wireless tuning via the SpeedyBee App, eliminating the need for a computer on-site.

Image: Overview of Wireless Tuning 2.0 features and benefits.

Image: Screenshot of the SpeedyBee App FC Tuning interface.
- PCB-Mounted Frame and Pad Redesign: More compact and easier to install. Newly designed flight controller and ESC pad shapes minimize solder-burr issues, making soldering easier and more precise. The board frame is designed to avoid the ESC soldering area, allowing maintenance without removing the flight controller.

Image: Diagram illustrating the redesigned PCB-mounted frame and soldering pads.
- All-New Model Aircraft ESC Hardware Design: Redundancy upgraded with built-in spike voltage and back-EMF suppression, plus protection against accidental electrostatic startup. True Ratings: 55A continuous, 70A peak (second-generation testing standard, actual performance exceeds previous 60A). Equipped with 24 new high-quality genuine TDK capacitors.

Image: Visual representation of the upgraded ESC hardware design with enhanced redundancy.

Image: Exploded view showing heatsink, nickel-plated bus bars, and new high-spec 40V MOSFETs within the ESC.
- Integrated Smart Switch: Easily control the 5V output via the remote controller using the configurator, delivering a steady 1.5A current without needing any extra electronic switch, supporting DIY night lighting and other creative applications.

Image: Diagram illustrating the integrated smart switch functionality.
- Dual-Upgrade Power Architecture: Innovative power architecture with independent supply for peripherals and internal chipsets, effectively isolating RF noise and electrical interference from external devices such as the VTX. Includes a high-performance DC-DC solution with peaks up to 42V, providing faster transient response and superior electrical performance, and full protection against surges, back-EMF, over-temperature, overcurrent, and overload. Offers a 9V output for VTX, configurable via remote controller switch.

Image: Visual representation of the dual-upgrade power architecture.
- Onboard STM32F405 Main Controller: Provides stable performance with multi-platform system support. Compatible with Betaflight, INAV, and ArduPilot (preloaded with Betaflight; future support for INAV and ArduPilot). Main frequency up to 168MHz and 1MB of built-in flash storage.

Image: Close-up of the STM32F405 main controller chip.

Image: Bar chart comparing STM32F405 main frequency and flash storage with other MCUs.
- Supports X4 Meteor LED Strips: Controllable via Betaflight.

Image: Example of X4 Meteor LED strips in use.
- Optional Smart Voltage Tester + Short-Circuit Protection Tool: (Deluxe version only) Includes a digital display, voltage and current measurement, intelligent capacitor charging detection, selectable 1/2A protection mode, short-circuit response as fast as 5ms, long-time power-on and secondary passive overload protection, ensuring safe operation.

Image: The Smart Voltage Tester and Short-Circuit Protection Tool.
5. Setup and Installation
5.1 Dimensions

Image: Detailed dimensions of the F405 V5 Flight Controller and OX32 55A ESC.
- Flight Controller: 39mm (L) × 39mm (W) × 4.9mm (H)
- ESC: 40.9mm (L) × 44.9mm (W) × 8.0mm (H) (incl. heatsink)
- Mounting Holes: 30.5 × 30.5mm (Ø4mm), side opening
5.2 Layout and Pinout

Image: Detailed layout and pinout diagram for the F405 V5 Flight Controller, showing connections for Servo, FPV Camera, Buzzer, Electronic Switch, Firmware Control LED, Front Receiver, Gyroscope, Bluetooth Chip, Bluetooth Antenna, Barometer, 4-Level LED Battery Indicator, BOOT Button, USB Type-C Port, STM32F405 Main Chip, LEDs (Blue, Green, Orange, Red), GPS & Compass, VTX (HD/Analog), Receiver, 10pin Connector (to Model Aircraft ESC), 9V BEC, 5V BEC, Internal 5V BEC, External Type-C Port Pads, OSD Chip, HD VTX (Direct Plug Connector).
5.3 FC and ESC Wiring Instructions
The stack supports both soldered and direct plug connections. Ensure proper orientation and secure connections.

Image: Wiring instructions showing both soldering and direct plug methods for connecting the FC and ESC. Also illustrates standard and reverse ESC installation methods.
- Soldering Method: Connect the corresponding pads on the FC and ESC as indicated in the diagram.
- Direct Plug Method: Use the provided 10-pin connector cable to link the FC and ESC.
- Installation: Use M3 black silicone washers when fixing the Model Aircraft stack to ensure sufficient space between the flight controller and the ESC.
5.4 Connection with FC & Motors
Connect your motors to the ESC following the diagram below. It is strongly recommended to use the included 1000uF solid capacitor to protect the AIO flight controller from being damaged by instantaneous voltage spikes when powered on.

Image: Wiring diagram showing connections for Motor 1-4, 1000uF Solid Capacitor, and XT60 Power Cable to the ESC.
5.5 Detailed Wiring Diagram (Soldered Connection)

Image: Comprehensive soldered wiring diagram for the F405 V5 FC, showing connections for Servos, Buzzer, LED Strips, GPS, TX ULTRA, TX 800, and various receivers.
5.6 BLS 55A 4-in-1 ESC Internal Layout

Image: Internal component layout of the BLS 55A 4-in-1 ESC, highlighting Current Distribution Copper Busbars, Filter Capacitors, Motors, Positive/Negative Power Pads, Current Sense Resistor, 10pin Flight Controller Connector, Driver Chips, and TVS Diode.
6. Operating Instructions
6.1 BOOT Button Functionality
- DFU Mode: Hold the BOOT button while powering on the flight controller to force it into DFU mode for firmware flashing.
- LED Control: When powered and in standby, a short-press of the BOOT button cycles through different LED display modes. A long-press switches between SB-LED and ST-LED modes. In ST-LED mode, LED1–LED4 are controlled by the FC firmware.
6.2 Wireless Tuning via SpeedyBee App
The SpeedyBee F405 V5 supports full-featured wireless tuning through the SpeedyBee App. This allows for FC firmware flashing and parameter tuning without needing a physical USB connection to a computer.
- Connection: Connect to the FC via Bluetooth using the SpeedyBee App.
- Firmware Upgrade: Perform wireless FC firmware upgrades directly from the app.
- Parameter Tuning: Adjust flight controller parameters and settings conveniently from your mobile device.
6.3 9V Output Control
The independent 9V BEC output can be remotely controlled (on/off) via a configurable switch on your remote controller. This is useful for powering VTX units or other peripherals only when needed.
7. Maintenance
7.1 Conformal Coating
The SpeedyBee F405 V5 Flight Controller and ESC come with a factory-applied conformal coating. This coating provides extra protection against moisture, solder residue, plant sap, and other harsh environmental conditions, enhancing the durability and longevity of your stack.

Image: Illustration of the factory-applied conformal coating process.
7.2 General Care
- Keep the stack clean and free from dust and debris.
- Avoid exposing the unit to extreme temperatures or direct sunlight for prolonged periods.
- Regularly inspect all connections for signs of wear or damage.
8. Troubleshooting
- No Power/Intermittent Power: Check all power connections, including the XT60 cable and the 1000uF solid capacitor. Ensure the battery is fully charged and correctly connected.
- Flight Controller Not Responding: Try connecting the FC to the SpeedyBee App or Betaflight Configurator via USB. If it doesn't connect, attempt to enter DFU mode by holding the BOOT button during power-up and re-flash the firmware.
- Motor Issues: Verify ESC signal connections to the FC and motor connections to the ESC. Ensure the ESC firmware (OX32) is correctly flashed and configured. Check for any physical damage to motors or ESC.
- Bluetooth Connectivity Issues: Ensure Bluetooth is enabled on your mobile device and the SpeedyBee App has necessary permissions. Restart both the FC and your device.
- LEDs Not Functioning: Check LED strip connections. Use the BOOT button to cycle through LED modes or switch between SB-LED and ST-LED modes. Verify LED settings in Betaflight.
- GPS/Receiver Issues: Confirm correct wiring for GPS and receiver modules. Check UART configurations in Betaflight. Ensure 4.5V output is sufficient if powering these peripherals from the FC.
9. User Tips
- Voltage Spike Protection: Always use the included 1000uF solid capacitor. This is crucial for protecting the flight controller from damaging voltage spikes, especially during initial power-up or aggressive maneuvers.
- Wireless Convenience: Leverage the SpeedyBee App for all your tuning and firmware update needs. It significantly simplifies field adjustments and eliminates the hassle of carrying a laptop.
- Firmware Compatibility: For advanced gyroscope features, ensure your Betaflight firmware is version 4.6.0 or later. Regularly check for updates to both FC and ESC firmware for optimal performance and new features.
- Soldering Best Practices: Take advantage of the redesigned PCB pads for easier soldering. If you're new to soldering, consider using the optional soldering practice board (Deluxe version) before working on your main components.
- Custom LED Effects: Experiment with the Meteor LED Strip Pads and the BOOT button functions to customize your drone's lighting.
10. Warranty and Support
For warranty information, technical support, and further assistance, please refer to the official SpeedyBee website or contact your retailer. Keep your proof of purchase for any warranty claims.