1. Introduction
Thank you for purchasing the NieNie LED Digital Alarm Clock. This device offers multiple functions including time, date, day of the week, temperature, humidity display, dual alarms, timer, and countdown features. Please read this manual carefully before use to ensure proper operation and to fully utilize all features.
2. Product Features
- Multi-Display: Time, date, day of the week, temperature, and humidity displayed simultaneously on one screen.
- Adjustable Brightness: 3 manual levels (L-01, L-02, L-03), Auto-Sensitive (L-AU), and Auto-Sensitive with Sleep Mode (L-SL).
- Dual Alarm: Two independent alarms with options for single, double break, or daily alarm cycles, including a snooze function.
- Timing Functions: Integrated timer and countdown functions, up to 99 minutes and 59 seconds.
- Dual Power Supply: Operates via DC5V USB cable (for continuous display) or 3xAA batteries (for temporary display with power-saving mode).
- Daylight Saving Time (DST): Quick toggle for DST.
- Time Format: Switch between 12-hour and 24-hour formats.
- Temperature Units: Switch between Celsius (°C) and Fahrenheit (°F).
3. Setup
3.1 Unpacking
Carefully remove all components from the packaging. Please check that all items are present:
- 1 x LED Digital Alarm Clock
- 1 x Instruction Manual
- 1 x 1.5M USB Cable
3.2 Powering On
Your alarm clock can be powered by two methods:
- DC5V USB Cable (Recommended for continuous display): Connect the provided USB cable to the DC5V port on the back of the alarm clock and plug the other end into a USB power adapter (not included) or a powered USB port. The display will remain continuously on.
- 3 x AA Batteries (for temporary display): Open the battery compartment on the back of the clock and insert three AA batteries (not included), ensuring correct polarity (+/-). In battery-powered mode, the screen will turn off after 10 seconds of inactivity to conserve power. Press any button to wake the display for 5-10 seconds.

Figure 1: Two Power Supply Methods
3.3 Initial Setup
After powering on, the clock will display default settings. You will need to set the current time, date, and other preferences as described in the Operating section.
4. Operating Instructions
4.1 Key Functions Overview
- SET: Short press to switch display mode (Time → Date → Temperature → Humidity). Long press to enter setting mode.
- UP: Short press to increase value. Long press for fast adjustment. In time display, short press to switch 12/24H format.
- DOWN: Short press to decrease value. Long press for fast adjustment. In time display, short press to switch °C/°F.
- ALARM: Short press to view Alarm 1 or Alarm 2 settings. Long press to enter alarm setting mode.
- TIMER: Short press to start/stop the timer. Long press to reset the timer.
- DST: Short press to toggle Daylight Saving Time (DST) ON/OFF.
- BRIGHTNESS: Short press to cycle through brightness levels (L-01, L-02, L-03, L-AU, L-SL).
4.2 Setting Time and Date
- Long press the SET button to enter setting mode. The Year will start flashing.
- Use the UP or DOWN buttons to adjust the Year.
- Press SET again to confirm the Year and move to Month setting.
- Repeat steps 2 and 3 for Month, Day, 12/24H format, Hour, and Minute.
- After setting the Minute, press SET one last time to exit setting mode.
4.3 Setting Alarms
- Long press the ALARM button to enter alarm setting mode. Alarm 1 Hour will start flashing.
- Use the UP or DOWN buttons to adjust the Alarm 1 Hour.
- Press ALARM again to confirm and move to Alarm 1 Minute.
- Repeat for Alarm 1 Minute.
- Press ALARM to set Alarm 1 Mode (OFF/ON).
- Press ALARM to set Alarm 1 Cycle (1-7 for Mon-Sun, 1-5 for Mon-Fri, 6-7 for Sat-Sun).
- Repeat steps 2-6 for Alarm 2 settings.
- After setting Alarm 2 Cycle, press ALARM one last time to exit alarm setting mode.
4.4 Snooze Function
When an alarm sounds, press any button (except ALARM) to activate the snooze function. The alarm will sound again after 5 minutes. To turn off the alarm completely, press the ALARM button when it is sounding.
4.5 Using Timer and Countdown

Figure 2: Timing and Countdown Display
- Setting Timer/Countdown: Long press the TIMER button. The Minute will start flashing. Use UP or DOWN to adjust minutes, then press TIMER to move to seconds. Adjust seconds with UP or DOWN. Press TIMER again to confirm and exit setting mode.
- Starting/Stopping: Short press the TIMER button to start or pause the timer/countdown.
- Resetting: Long press the TIMER button to reset the timer/countdown to its set value or to zero if not set.
4.6 Brightness Adjustment

Figure 3: Brightness Adjustment Levels
Short press the BRIGHTNESS button to cycle through the following display modes:
- L-01: Lowest manual brightness.
- L-02: Medium manual brightness.
- L-03: Highest manual brightness.
- L-AU: Auto-sensitive brightness (adjusts automatically based on ambient light).
- L-SL: Auto-sensitive brightness with Sleep Mode (dims further during sleep hours).
4.7 12/24 Hour Format

Figure 4: 12/24 Hour Format Examples
In time display mode, short press the UP button to switch between 12-hour and 24-hour formats.
4.8 Celsius/Fahrenheit Switching

Figure 5: Celsius/Fahrenheit Switching
In time display mode, short press the DOWN button to switch between Celsius (°C) and Fahrenheit (°F) temperature units.
4.9 Daylight Saving Time (DST)
Short press the DST button to toggle Daylight Saving Time ON or OFF. When DST is active, a 'DST' indicator will appear on the display.
5. Maintenance
- Cleaning: To clean the clock, gently wipe the display and casing with a soft, dry cloth. Do not use abrasive cleaners, solvents, or spray directly onto the unit.
- Battery Replacement: If using batteries, replace all three AA batteries simultaneously when the display becomes dim or functions become erratic. Ensure correct polarity.
- Storage: If the clock will not be used for an extended period, remove the batteries to prevent leakage and damage.
6. Troubleshooting
- Display is off or dim:
- Check if the USB cable is securely connected and powered.
- If using batteries, ensure they are fresh and correctly inserted. - Display turns off after 10 seconds:
- This is normal behavior when powered by batteries to conserve energy. For continuous display, use the USB power supply. - Time/Date resets after power loss:
- The clock does not have an internal backup battery for settings. If both USB power and AA batteries are removed, settings will reset. - Temperature/Humidity readings seem inaccurate:
- Environmental sensors can have slight variations. Ensure the clock is not placed in direct sunlight, near heat sources, or in areas with extreme drafts, which can affect readings. - Buttons are unresponsive:
- Try disconnecting and reconnecting the power source (USB or batteries) to reset the device.
7. Specifications

Figure 6: Size Information
| Feature | Specification |
|---|---|
| Model Numbers | DS-6671, 5512 |
| Brand | NieNie |
| Dimensions (L x H x W) | 26.5 cm x 7 cm x 3.5 cm (10.43 in x 2.76 in x 1.38 in) |
| Power Input | DC5V via USB cable, 3 x AA batteries |
| Display Type | LED |
| Material | Plastic |
| Functions | Time, Date, Week, Temperature, Humidity, Dual Alarm, Timer, Countdown, DST, Snooze, Auto Dimming |
8. User Tips
- For a continuously lit display, always use the USB power cable. Battery power is primarily for portability or temporary use, as the display will turn off after 10 seconds to save power.
- If you plan to mount the clock on a wall, note that it is primarily designed for tabletop use. Creative mounting solutions may be required as specific wall-mounting holes are not provided.
- Keep the instruction manual handy for quick reference on setting various functions.
9. Warranty and Support
For any questions, technical support, or warranty inquiries regarding your NieNie LED Digital Alarm Clock, please contact the seller or retailer from whom you purchased the product. Please retain your proof of purchase for any warranty claims.