MESTEK WM700B

Contents

MESTEK WM700B Non-Contact Wood Moisture Meter Instruction Manual

Model: WM700B | Brand: MESTEK

Introduction

The MESTEK WM700B is a non-contact digital hygrometer designed for quick and efficient moisture detection in various materials without causing damage. It features high accuracy, a clear HD LCD screen with backlight, and multiple functions including self-calibration, data hold, MAX/MIN record, auto-shutdown, and an adjustable alarm function. This manual provides essential information for the safe and effective use of your WM700B moisture meter.

Safety Information

  • Read all instructions carefully before use.
  • Do not attempt to disassemble or modify the device.
  • Keep the device away from water and extreme temperatures.
  • Ensure batteries are inserted correctly according to polarity markings.
  • Remove batteries if the device will not be used for an extended period.
  • This device is for measurement purposes only and should not be used for medical or safety-critical applications.

Product Overview

The MESTEK WM700B utilizes a spherical probe for non-destructive moisture measurement. Its intuitive interface and robust design make it suitable for woodworking, flooring, construction, and general home inspection tasks.

MESTEK WM700B Non-Contact Wood Moisture Meter with spherical probe and digital display.

Figure 1: MESTEK WM700B Non-Contact Wood Moisture Meter

Key Features:

  • Non-destructive spherical probe measurement.
  • HD LCD screen with backlight and multi-color display.
  • Self-calibration function.
  • Data hold function.
  • MAX/MIN value recording.
  • Automatic shutdown (10 minutes inactivity).
  • Adjustable moisture alarm function.
  • Low power indicator.
  • Measuring depth: 20-40mm.

Component Identification:

Labeled diagram of MESTEK WM700B components and controls.

Figure 2: WM700B Component Diagram

  • 1. Non-destructive Moisture sensor (Spherical probe, Diameter: 25mm)
  • 2. Color screen
  • 3. Power on/off button
  • 4. Alarm value set button (SET)
  • 5. Calibration keys / Data management (MEAS)
  • 6. Alarm Numerical Adaptation (-) button
  • 7. Alarm Numerical Adaptation (+) button

Setup

Battery Installation:

The MESTEK WM700B requires 3 AAA batteries (not included). To install:

  1. Locate the battery compartment on the back of the device.
  2. Use a small screwdriver to open the battery compartment cover.
  3. Insert 3 AAA batteries, ensuring correct polarity (+/-) as indicated inside the compartment.
  4. Replace the battery compartment cover and secure it with the screw.

Video 1: Battery Installation and Basic Operation

Operating Instructions

Power On/Off:

  • Press the Power On/Off button (labeled with a power symbol) to turn the device on.
  • The device will automatically shut down after 10 minutes of inactivity to conserve battery life.

Calibration:

Before each use, it is recommended to calibrate the device for accurate readings.

  1. Turn on the device.
  2. Ensure the spherical probe is in the air, not touching any surface.
  3. Press the MEAS key. The display will show "CAL" indicating calibration is in progress.
  4. Once "CAL" disappears and the display shows "0.0", calibration is complete.
Step-by-step guide for calibrating the MESTEK WM700B moisture meter.

Figure 3: Calibration Steps

Taking Measurements:

The WM700B uses a non-destructive spherical probe to measure moisture content. The measuring depth is approximately 20-40mm.

  1. After calibration, gently place the spherical probe against the surface of the material you wish to measure.
  2. Ensure full contact between the probe and the material for accurate readings.
  3. The moisture content will be displayed on the HD LCD screen. The display includes a color analog bar (green for DRY, yellow for RISK, red for WET) and a numerical value.
MESTEK WM700B showing inductive measurement for drywall, masonry, and wood.

Figure 4: Inductive Measurement for Various Materials

Data Hold Function:

  • Press the HOLD button (often integrated with MEAS or a dedicated button) to freeze the current reading on the screen.
  • Press it again to release the hold and resume live measurement.

MAX/MIN Record:

  • The device can record the maximum and minimum moisture values detected during a measurement session.
  • Refer to the display for MAX/MIN indicators. The specific button to toggle this function might be the MODE button or a dedicated MAX/MIN button.

Moisture Alarm Function:

The WM700B features an adjustable alarm to alert you when moisture levels exceed a set threshold.

  1. Press the SET button to enter alarm setting mode.
  2. Use the Alarm Numerical Adaptation (+) and (-) buttons to adjust the alarm threshold value.
  3. Press SET again to confirm and exit.
  4. When the measured value exceeds the set RISK threshold, the device will emit a "Beep" sound. If it exceeds the WET threshold, it will emit a faster "BeepBeep" sound.
MESTEK WM700B demonstrating moisture alarm function with DRY, RISK, WET indicators.

Figure 5: Moisture Alarm Function

Material Moisture Ranges:

The moisture status (DRY, RISK, WET) varies depending on the material. Refer to the table below for general guidelines:

Moisture comparison table for building materials (Holzwerkstoffe, Mauerwerk, Gipskarton/Zement) with DRY, RISK, WET ranges.

Figure 6: Moisture Status by Material Type

Moisture Status Guidelines
Building MaterialMoisture Range (Digit)Moisture Status
Wood Materials< 25DRY
25 - 50RISK
> 50WET
Masonry< 30DRY
30 - 60RISK
> 60WET
Gypsum Board/Cement< 50DRY
50 - 80RISK
> 80WET

Maintenance

  • Cleaning: Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Storage: Store the device in a cool, dry place when not in use. Remove batteries if storing for extended periods to prevent leakage.
  • Battery Replacement: Replace batteries when the low power indicator appears on the screen.

Troubleshooting

  • Device does not power on: Check battery installation and ensure batteries are not depleted. Replace if necessary.
  • Inaccurate readings: Ensure the device is calibrated before use. Make sure the spherical probe has full contact with the material surface. Avoid measuring near strong electromagnetic fields.
  • No alarm sound: Check if the alarm threshold is set correctly.

Specifications

ItemValue
Brand NameMESTEK
Model NumberWM700B
TypeMoisture Meter
Detection Thickness40mm
Automatic Shut-down10 minutes
Battery3 x 1.5V AAA (not included)
Working Current35mA
Operating Temperature0~40°C
Working Humidity0%~70%
Storage Environment-10~50°C (5%~95%RH)
ColorBlack
CertificationCE, EAC, FCC, RoHS, UL
OriginMainland China
Warranty3 years

User Tips

  • For consistent results, always calibrate the meter in the air before taking measurements.
  • When measuring, ensure the spherical probe is flat against the surface to get the most accurate reading within the 20-40mm depth.
  • Pay attention to the color bar on the display: green indicates dry, yellow indicates risk, and red indicates wet.
  • Utilize the MAX/MIN record function when scanning large areas to quickly identify the highest and lowest moisture points.
  • The alarm function is particularly useful for quickly identifying areas exceeding a safe moisture threshold without constantly monitoring the display.

Warranty and Support

The MESTEK WM700B comes with a 3-year warranty from the date of purchase. For technical support, warranty claims, or service inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

© 2023 MESTEK. All rights reserved.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.