HOMEFISH AC 100-240V DC 42V 2A Electric Scooter Power Adapter

Contents

HOMEFISH Electric Scooter Power Adapter

Model: AC 100-240V DC 42V 2A

Introduction

This manual provides essential information for the safe and efficient use of your HOMEFISH Electric Scooter Power Adapter. Please read this manual thoroughly before using the product and retain it for future reference.

Safety Information

  • WARNING: Beware of flames, sparks, and explosive gases. Keep adequate ventilation to avoid fire.
  • Do not use the charger in wet environments.
  • Ensure the charger's voltage and polarity are consistent with your battery pack to prevent damage.
  • This charger is designed for lithium-ion battery packs (24-36V). Do not use it for lead-acid batteries.

Setup

1. Package Contents

Your package should include:

  • 1 x 42V 2A Lithium Battery Charger with 5.5mm 1-Prong DC Plug
  • 1 x AC Power Cord (US, EU, or UK plug, depending on selection)
  • 4 x Adapter Connectors:
    • Adapter to 8mm 3-Prong Connector
    • Adapter to 12mm 3-Prong Connector
    • Adapter to 8mm RCA Connector
    • Adapter to 3-Pin Male XLR Connector

2. Power Cord and DC Plug Options

The charger is compatible with various regional power outlets and comes with a standard 5.5mm DC interface. A selection of adapter cables is provided for wide compatibility.

Image showing US, UK, and EU power cord plug options.
Optional Power Cord Specifications: US, UK, and EU plugs available.
Close-up of the standard 5.5mm DC plug with dimensions and cable length.
Standard DC Plug: 5.5mm DC interface with approximately 1 meter cable length.
Main charger unit with various DC output connectors and AC input plug.
The charger comes with a 5.5mm DC plug and includes adapters for 8mm 3-Prong, 12mm 3-Prong, 8mm RCA, and 3-Pin Male XLR connectors.

Operating Instructions

1. Pre-Charging Check

  • Ensure the incoming and outgoing voltage and polarity of the charger are consistent with your battery pack. Using a charger with incorrect polarity or voltage can cause damage.
  • Always disconnect the power supply before connecting or disconnecting the charger from the battery.

2. Charging Process

  1. Connect the AC power cord to a power outlet. The indicator light on the charger will turn green.
  2. Connect the appropriate DC plug (or adapter) from the charger to the charging port of your electric vehicle's battery. The indicator light will turn red, indicating that charging is in progress.
  3. Once the battery is fully charged, the indicator light will turn green again. The charger features intelligent safe charging with full automatic disconnect and overcharge protection.
Close-up of charger indicator light showing red for charging and green for finished.
Charging Indicator Light: Red indicates charging, Green indicates charging finished.
Image showing red light for charging and green light for full, emphasizing automatic disconnect.
Intelligent Safe Charging: Automatic disconnect when full, indicated by a green light.

Maintenance

  • Keep the charger in a dry environment. Avoid exposure to moisture or liquids.
  • Do not expose the charger to extreme temperatures.
  • Clean the charger with a dry, soft cloth. Do not use harsh chemicals or abrasive cleaners.
  • Regularly inspect the power cord and connectors for any signs of damage.

Troubleshooting

If you encounter issues with your charger, refer to the table below for common problems and solutions.

Fault Phenomenon Fault Analysis Processing Method
When the charger is charging, the indicator light is always green or flashing. The connection plug between the charger and the battery box is not connected well. Please reconfirm whether it is inserted properly.
Check the battery box and socket for voltage output with digital multimeter. Please open the battery box and check whether the internal connecting wire and fuse are open.
The positive and negative polarity of the battery box socket is inconsistent with the positive and negative polarity marked on the charger instructions. Please adjust the positive and negative polarity of electric vehicle battery charging interface pair.
Charger indicator light does not illuminate. The output line is damaged or poorly welded. Post processing of measurement with universal meter.
The charger is damaged or there is no power in the power socket. Replace the charger and check the power socket.

Specifications

Parameter Value
Product Name Lithium battery intelligent charger
Input Parameter AC 100-240V, 50/60Hz, 2A (max)
Output Parameter DC 42V 2A (Other output configurations like 29.4V2A and 54.6V2A may exist for different models)
Power 84W (for 42V 2A model)
Applicability For 24-36V Lithium Battery Packs
Input Plug Options US, EU, UK (Optional)
Output Plug 5.5 x 2.5mm (Outer Diameter x Inner Diameter)
Power Supply Cable Length Approx. 95cm
Adapter Cable Length Approx. 90cm
Dimensions (Charger Unit) 11.4cm x 5.2cm x 3cm

User Tips

  • Always double-check the connector type of your battery before purchasing and using the charger to ensure compatibility.
  • For optimal battery life, avoid leaving the battery connected to the charger for extended periods after the green light indicates a full charge, although the charger has overcharge protection.
  • Store the charger in a cool, dry place when not in use.

Warranty and Support

For warranty information, please refer to the terms and conditions provided by your retailer or contact the seller directly. For additional guidance, you may consult the official user manual PDF:

View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.