1. Product Overview
The iFlight Borg Mini 60 ESC is a high-performance 4-in-1 Electronic Speed Controller designed for FPV racing drones. It features an integrated anti-spark circuit and high polymer capacitors, eliminating the need for external capacitors in 5-inch racing models. This design simplifies installation, reduces weight, and enhances reliability and performance for competitive racing.
Key Features:
- Supports 2-6S Battery Input for versatile power options.
- 8-Layer high flow resistant PCB for continuous current handling of 60A (peak 65A).
- Integrated Anti-Spark Filter protects equipment from voltage spikes.
- Built-in High Polymer Capacitors eliminate the need for external capacitors in racing models.
- FPC Ribbon Cable Connection ensures a reliable link between the flight controller and ESC.
Product Video:
A visual overview of the iFlight Borg Mini 60 ESC and its components.
2. Specifications
| Parameter | Value |
|---|---|
| Product Name | Borg Mini 60 ESC |
| Input Voltage | 2-6S (Supports LIHV battery) |
| Max. Continuous Current | 60A |
| Max. Burst Current | 65A (10s) |
| MCU | STM32G071N |
| Driver | FD6288 |
| Firmware | BL32 (32bit ESC) |
| Target | IFLIGHT_BLITZ_G3 32.9 |
| Current Sensor | Yes |
| BEC | No |
| Telemetry | Supported |
| Bidirectional DSHOT | Supported |
| Dimensions | 42mm x 35mm (±1mm) |
| Mounting Holes | 20mm x 20mm / Φ4mm |
| Weight | 10.1g (±1g) |
| Protocol | DShot150/300/600, MultiShot, OneShot etc. |
Dimensions:

Side and top view of the Borg Mini 60 ESC with detailed measurements: 1.8mm thickness, 6mm total height, 20x20mm mounting holes with 4mm diameter, 35mm width, and 42mm length.
3. Setup and Installation
Careful installation is crucial for optimal performance and safety. Please follow these steps:
3.1 Wiring Diagram:

This diagram illustrates the connections for the Borg Mini 60 ESC. It shows the four motor connections (MOTOR 1-4), the VBAT (battery positive) and GND (ground) connections. It also indicates the capacitor positive and negative ends.
Important Note for Capacitor Installation:
- For 6-inch and above drone builds, a 50V 470uF capacitor needs to be added.
- Solder the capacitor at the position indicated by the arrow in the diagram, ensuring correct polarity (positive to VBAT, negative to GND).
3.2 Pinout Details:
The pinout for the ESC is as follows:
- GND: Ground connection
- VBAT: Battery Voltage Input
- NC: No Connection
- M4, M3, M2, M1: Motor Signal Outputs (for Motors 4, 3, 2, 1 respectively)
- CUR: Current Sensor Output
- Rx: Receiver Signal Input (for telemetry)
3.3 Mounting:
- The ESC features 20x20mm mounting holes with a 4mm diameter.
- Use the provided silicon grommets to absorb vibrations and secure the ESC to your drone frame.
- Ensure proper alignment and avoid overtightening screws to prevent damage to the PCB.
3.4 Connecting to Flight Controller:
Utilize the FPC ribbon cable for a secure and reliable connection between the Borg Mini 60 ESC and your compatible flight controller. Refer to your flight controller's manual for specific FPC connector orientation and pin mapping.
4. Operation
Once the ESC is correctly installed and wired, follow these general steps for operation:
4.1 Firmware:
- The Borg Mini 60 ESC comes pre-flashed with BL32 (32bit ESC) firmware.
- The target firmware is IFLIGHT_BLITZ_G3 32.9.
- If updating firmware, always use the correct target and follow the instructions provided by the firmware developer (e.g., BLHeliSuite32).
4.2 Protocols:
This ESC supports various digital and analog protocols:
- Digital: DShot150, DShot300, DShot600
- Analog: MultiShot, OneShot
For best performance and reliability, DShot600 is generally recommended with compatible flight controllers.
4.3 Powering On:
- Connect your 2-6S LiPo or LIHV battery to the main power leads of the ESC.
- Ensure all connections are secure before powering on.
- Listen for the ESC initialization tones, indicating it has powered up correctly.
5. Maintenance
Regular maintenance helps prolong the life and performance of your ESC:
- Inspection: Periodically check all solder joints and connections for any signs of wear, corrosion, or damage.
- Cleaning: Keep the ESC free from dust, dirt, and debris. Use a soft brush or compressed air for cleaning. Avoid using liquids directly on the board.
- Environmental Protection: Protect the ESC from moisture and extreme temperatures. If flying in damp conditions, consider conformal coating for added protection.
- Physical Damage: After any crash or hard landing, inspect the ESC for physical damage, such as cracked components or bent pins.
6. Troubleshooting
If you encounter issues with your Borg Mini 60 ESC, consider the following:
- No Power/No Initialization Tones:
- Check battery connection and voltage.
- Verify main power leads are correctly soldered and not shorted.
- Ensure the flight controller is powered and sending signals.
- Motors Not Spinning/Erratic Behavior:
- Check motor connections to the ESC.
- Verify motor direction in your flight controller software (e.g., Betaflight, EmuFlight).
- Ensure ESC firmware is up-to-date and correctly configured for your motors.
- Check for bent motor shafts or damaged propellers.
- Overheating:
- Ensure adequate airflow around the ESC.
- Check for motor issues (e.g., binding, incorrect KV for prop size) that might draw excessive current.
- Verify propeller balance.
- Desyncs/Random Motor Stuttering:
- Increase D-term filtering in your flight controller.
- Ensure motor wires are not too long or too thin.
- Check for loose connections or cold solder joints.
- Consider adjusting motor timing in BLHeliSuite32 (advanced users only).
7. User Tips
- Solder Quality: Always ensure clean and strong solder joints for all connections, especially power and motor leads, to prevent intermittent issues and maximize current flow.
- Cable Management: Keep motor and power cables as short as reasonably possible to reduce electrical noise and weight.
- Firmware Updates: While the ESC comes with stable firmware, periodically check the manufacturer's website for updated BLHeli32 firmware versions that might offer performance improvements or bug fixes.
- Testing: Before your first flight, always perform a bench test with propellers removed to verify motor direction and responsiveness.
8. Packing List
The following items are included with your iFlight Borg Mini 60 ESC:
- 1 x Borg Mini 60 ESC
- 1 x Cables set
- 4 x Silicon grommets
9. Warranty and Support
For warranty claims, technical support, or further assistance, please contact the official iFlight customer service or the retailer from whom you purchased the product. Keep your proof of purchase for any warranty-related inquiries.