Ourlife Q100 4K Action Camera User Manual

1. Product Overview

The Ourlife Q100 is a versatile 4K action camera designed for capturing high-quality video and photos in various environments, including underwater. It features a 170° ultra-wide angle lens, 4x digital zoom, a 2.0-inch IPS display, and built-in Wi-Fi for easy sharing and control.

2. Package Contents

Please check the package to ensure all items are present:

• Ourlife Q100 Action Camera
• Waterproof Housing
• Handle Bar/Pole Mount
• 2 x 900mAh Batteries
• Battery Charger
• Clip 1
• Data Line (USB Cable)
• Mount 1, Mount 2, Mount 3, Mount 4
• Bandages (various sizes)
• User Manual

3. Setup Guide

3.1 Battery Installation and Charging

The camera comes with two 900mAh removable/replaceable batteries. Ensure batteries are fully charged before first use.

1. Open the battery compartment cover on the bottom of the camera.
2. Insert a battery, ensuring the correct orientation.
3. Close the battery compartment cover securely.
4. To charge, use the provided battery charger and USB cable. Connect the charger to a USB power source. The indicator light on the charger will show charging status.

3.2 Memory Card Installation

The camera supports MicroSD/TF cards up to 64GB. A high-speed card (Class 10 or higher) is recommended for 4K video recording.

1. Locate the memory card slot on the side of the camera.
2. Insert the MicroSD card with the gold contacts facing the back of the camera until it clicks into place.
3. To remove, gently push the card until it pops out.

3.3 Attaching the Waterproof Housing

The included waterproof housing allows the camera to be submerged up to 30 meters (approximately 98 feet).

1. Ensure the camera is dry and clean before placing it into the housing.
2. Open the latch on the top of the waterproof housing.
3. Carefully place the camera inside the housing, ensuring it fits snugly.
4. Close the latch securely. Always test the housing without the camera first to ensure it is watertight.

4. Operating Instructions

4.1 Power On/Off and Mode Selection

• Power On: Press and hold the Power/Mode button (usually on the front) for a few seconds.
• Power Off: Press and hold the Power/Mode button for a few seconds until the screen turns off.
• Change Mode: Briefly press the Power/Mode button to cycle through video, photo, playback, and settings modes.

4.2 Video Recording

The camera supports 4K video recording at 30 frames per second (4K30FPS).

1. Switch to Video Mode.
2. Press the Shutter/OK button (usually on top) to start recording. A red indicator light will flash, and a timer will appear on the screen.
3. Press the Shutter/OK button again to stop recording.

4.3 Photo Capture

Capture high-resolution 16MP photos.

1. Switch to Photo Mode.
2. Press the Shutter/OK button to take a photo.

4.4 Digital Zoom

The camera features 4x digital zoom.

1. In Video or Photo Mode, use the Up/Down buttons (if available, or on-screen controls) to adjust the zoom level.
2. The screen will display the current zoom magnification (e.g., X2, X4).

4.5 Wide Angle Lens

The 170° ultra-wide angle lens provides an expansive field of view, enhancing perspective and capturing more of the scene.

4.6 2.0-inch IPS Display

The camera features a 2.0-inch IPS screen for live view, playback, and menu navigation.

4.7 Wi-Fi Connectivity

Connect the camera to your smartphone via 2.4G Wi-Fi for remote control, live preview, and file transfer.

1. Turn on Wi-Fi on the camera (usually via the settings menu).
2. On your smartphone, search for the camera's Wi-Fi network and connect.
3. Open the dedicated camera app (refer to the manual for app name) to control the camera.

4.8 Webcam Functionality

The Ourlife Q100 can be used as a webcam for video calls or streaming.

1. Connect the camera to your computer using the USB cable.
2. The camera should be recognized as a webcam without needing additional drivers.
3. Select the camera as your video input device in your video conferencing or streaming software.

4.9 Dash Cam Functionality

The camera supports various modes suitable for use as a dash cam, including driving mode, loop recording, motion detection, and upside-down display.

To use as a dash cam:

1. Mount the camera securely in your vehicle using appropriate mounts.
2. Access the camera's settings to enable 'Driving Mode' or 'Loop Recording'.
3. Ensure 'Motion Detection' is enabled if you wish for the camera to record automatically when motion is detected.
4. If needed, adjust the 'Upside Down' setting for correct video orientation.

5. Maintenance

5.1 Cleaning

• Camera Body: Use a soft, dry cloth to wipe the camera body. For stubborn dirt, slightly dampen the cloth with water.
• Lens: Use a lens cleaning cloth or specialized lens wipes. Avoid touching the lens with your fingers.
• Waterproof Housing: After use in saltwater, rinse the housing with fresh water and let it air dry. Ensure no sand or debris is trapped in the seals.

5.2 Battery Care

• Store batteries in a cool, dry place when not in use.
• Avoid fully discharging batteries frequently to prolong their lifespan.
• If storing for extended periods, charge batteries to about 50% capacity.

5.3 Storage

• Store the camera and accessories in a protective case to prevent scratches and damage.
• Keep away from extreme temperatures, high humidity, and strong magnetic fields.

6. Troubleshooting

Camera won't turn on:

Ensure the battery is fully charged and correctly inserted. Try using the second battery if available.

Video quality is poor:

Check that the lens is clean. Ensure you are using a high-speed MicroSD card (Class 10 or higher). Verify video resolution settings are set to 4K30FPS.

Wi-Fi connection issues:

Make sure Wi-Fi is enabled on the camera and your smartphone. Ensure you have the correct camera app installed. Try restarting both the camera and your smartphone.

Camera freezes:

Remove and reinsert the battery to perform a hard reset. If the issue persists, try formatting the memory card (this will erase all data).

Water leakage in housing:

Immediately remove the camera. Check the rubber seal (O-ring) for any dirt, hair, or damage. Ensure the latch is fully closed. Always perform a water test without the camera before diving.

7. Specifications

8. Warranty and Support

The Ourlife Q100 Action Camera is certified with CE, FCC, and RoHS standards, ensuring compliance with health, safety, and environmental protection regulations.

For technical support or warranty inquiries, please refer to the contact information provided by your retailer or the official Ourlife website.

9. User Tips

• Always format your MicroSD card in the camera before first use and periodically to maintain optimal performance.
• Carry spare charged batteries, especially for extended recording sessions, as 4K video consumes power quickly.
• When using the waterproof housing, double-check all seals and latches before submerging to prevent water damage.
• Experiment with different mounts and angles to capture unique perspectives of your activities.
• Utilize the Wi-Fi feature to quickly review footage on your phone and free up camera storage if needed.