SCHEPPACH SBP2.0

Contents

SCHEPPACH 20V SBP2.0 Electric Tool Battery User Manual

Model: SBP2.0 | Brand: SCHEPPACH

Introduction

This manual provides essential information for the safe and effective use, maintenance, and troubleshooting of your SCHEPPACH 20V SBP2.0 Li-Ion battery. Please read these instructions carefully before first use and keep them for future reference.

SCHEPPACH 20V SBP2.0 Li-Ion Battery front view
Figure 1: SCHEPPACH 20V SBP2.0 Li-Ion Battery

Safety Instructions

Always observe the following safety precautions to prevent injury or damage to the battery and connected tools:

  • Do not disassemble, open, or shred the battery pack.
  • Do not expose the battery to heat or fire. Avoid storage in direct sunlight.
  • Do not short-circuit a battery pack.
  • Do not expose the battery to mechanical shock.
  • In case of battery leakage, do not allow the liquid to come into contact with skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice.
  • Keep the battery pack clean and dry.
  • Do not use any charger other than that specifically provided for use with the equipment.
  • Do not leave a battery on prolonged charge when not in use.
  • Do not store the battery above 50°C (122°F).
  • Dispose of batteries properly according to local regulations.
Battery label with safety warnings and specifications
Figure 2: Battery label showing safety symbols (max 50°C, no fire, no disposal in trash) and certifications (CE, RoHS).

Setup and Initial Use

  1. Unpacking: Carefully remove the battery from its packaging. Inspect for any signs of damage.
  2. Initial Charge: Before first use, fully charge the battery using a compatible SCHEPPACH 20V battery charger. Refer to your charger's manual for specific charging instructions.
  3. Installation: Align the battery with the battery slot on your SCHEPPACH 20V electric tool. Push firmly until it clicks into place. Ensure it is securely seated.
Top view of the SCHEPPACH SBP2.0 battery showing tool interface
Figure 3: Top view of the battery, illustrating the connection points for power tools.

Operating the Battery

  • Powering Tools: Once installed, the battery will power your compatible SCHEPPACH 20V tool.
  • Checking Charge Level: The battery features an integrated charge indicator. Press the button on the battery to illuminate the LED lights, indicating the remaining charge.
    SCHEPPACH 20V SBP2.0 Li-Ion Battery with illuminated charge indicator
    Figure 4: Battery with illuminated charge indicator showing remaining power.
  • Removing Battery: To remove the battery, press the release latches on the sides of the battery pack and slide it out of the tool.

Maintenance

  • Cleaning: Keep the battery contacts clean and free of debris. Use a dry cloth to wipe the battery exterior. Do not use liquids or solvents.
  • Storage: Store the battery in a cool, dry place, away from direct sunlight and extreme temperatures. For long-term storage, it is recommended to store the battery at approximately 50% charge.
  • Charging: Do not overcharge or deep discharge the battery. Follow the charging instructions provided with your SCHEPPACH charger.

Troubleshooting

ProblemPossible CauseSolution
Battery not chargingCharger not plugged in; faulty charger; battery too hot/cold; damaged battery.Ensure charger is properly connected. Allow battery to reach room temperature. Check charger for damage. If battery is damaged, replace it.
Tool not powering onBattery not fully charged; battery not properly installed; faulty tool.Charge battery fully. Re-install battery, ensuring it clicks into place. Test with another battery if available.
Reduced run timeBattery nearing end of life; extreme operating conditions.Consider replacing the battery. Avoid using tools in extremely hot or cold environments.

Specifications

FeatureDetail
Model NumberSBP2.0
Brand NameJedila (Compatible with SCHEPPACH)
TypeLi-Ion
Nominal Capacity2Ah
Voltage / Rated Voltage20V
Energy40Wh
ApplicationElectric Tool (e.g., Electric Saw, Screwdriver, Cutting Machine, Angle Grinder)
Weight0.3KG
Max Operating Temperature50°C (122°F)
CertificationsCE, RoHS
Internal view of the battery pack showing individual Li-Ion cells
Figure 5: Internal components of the battery, including the Li-Ion cells.
Battery Management System (BMS) circuit board
Figure 6: The internal circuit board (BMS) responsible for battery management.

User Tips

  • Charger Compatibility: This battery is designed for SCHEPPACH 20V tools. Ensure you use a compatible 20V charger, as the battery is typically sold separately from the charger.
  • Temperature Management: For optimal performance and longevity, avoid charging or operating the battery in extreme temperatures. Allow a hot battery to cool down before charging.
  • Regular Use: Li-Ion batteries benefit from regular use. If storing for extended periods, charge to about 50% and recharge every few months.

Warranty and Support

For warranty information and technical support, please refer to the documentation provided with your purchase or contact the seller directly. Keep your proof of purchase for any warranty claims.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.