LEIRONG BPG BPT tube, BP200-B46, BPG silicone tube, BP200-B30

Contents

LEIRONG Peristaltic Pump Head User Manual

High Quality Laboratory, Food, and Medical Grade Peristaltic Pump Head

1. Product Overview

The LEIRONG Peristaltic Pump Head is designed for precise fluid transfer in various applications, including laboratory, food processing, and medical environments. It operates by compressing and relaxing a flexible tube, creating a positive displacement flow. This pump head is compatible with both BPT and silicone tubing, offering versatility for different fluid types and operational requirements.

Front view of the LEIRONG peristaltic pump head with tubing installed.
Figure 1: Front view of the LEIRONG Peristaltic Pump Head with tubing.

2. Setup and Installation

2.1 Mounting the Pump Head

The pump head is designed to be mounted onto a compatible motor or drive unit. Ensure the drive shaft of your motor matches the hexagonal interface on the back of the pump head.

  1. Align the hexagonal drive interface of the pump head with the drive shaft of your motor.
  2. Gently push the pump head onto the shaft until it is securely seated.
  3. If applicable, use any provided fasteners (screws, clamps) to secure the pump head to the motor housing.
Rear view of the pump head showing the hexagonal drive interface.
Figure 2: Rear view showing the hexagonal drive interface for motor attachment.

2.2 Tubing Installation

Proper tubing installation is crucial for optimal performance and to prevent leaks.

  1. Open the pump head cover. This usually involves releasing latches or screws, depending on the specific model.
  2. Select the appropriate BPT or silicone tubing for your application. Ensure the tubing diameter matches the pump head's specifications.
  3. Carefully insert the tubing into the pump head, guiding it along the rotor path. Ensure the tubing is seated correctly within the channels and under the rollers.
  4. Close the pump head cover, ensuring it latches securely. The tubing should be held firmly in place without being overly pinched or stretched.
  5. Connect the inlet and outlet ends of the tubing to your fluid source and destination, respectively.
Front view of the pump head with the cover removed, showing the rotor and tubing path.
Figure 3: Pump head with cover removed, illustrating the tubing path around the rotor.

3. Operating Instructions

Once the pump head is installed and tubing is connected, operation is controlled by the motor/drive unit it is attached to.

  1. Power On: Ensure the motor/drive unit is connected to a power source and turned on.
  2. Flow Rate Adjustment: The flow rate is primarily controlled by the speed of the motor. Refer to your motor/drive unit's manual for instructions on adjusting speed.
  3. Direction of Flow: The direction of fluid flow is determined by the rotation direction of the motor. Most peristaltic pumps allow for reversible flow.
  4. Monitoring: Observe the fluid flow to ensure proper operation and check for any leaks or blockages.
  5. Power Off: When finished, turn off the motor/drive unit.

4. Maintenance

Regular maintenance ensures the longevity and reliable performance of your peristaltic pump head.

4.1 Tubing Replacement

Peristaltic tubing is a wear component and should be replaced periodically, depending on usage and fluid type. Signs of wear include reduced flow, cracking, discoloration, or loss of elasticity.

  1. Turn off the pump and disconnect it from the power source.
  2. Disconnect the inlet and outlet tubing from your system.
  3. Open the pump head cover.
  4. Remove the old tubing.
  5. Clean the pump head interior if necessary (see 4.2 Cleaning).
  6. Install new tubing as described in Section 2.2.
  7. Close the pump head cover and reconnect the system.

4.2 Cleaning

Clean the pump head exterior and interior (when tubing is removed) with a damp cloth and mild detergent. Avoid using abrasive cleaners or solvents that could damage the plastic components. Ensure all parts are dry before reassembly.

4.3 Inspection

Periodically inspect the rollers and rotor for any signs of wear, damage, or debris accumulation. Ensure they rotate freely and smoothly. If any components appear damaged, contact support for replacement parts.

5. Troubleshooting

Problem Possible Cause Solution
No fluid flow or reduced flow
  • Tubing clogged or kinked
  • Tubing worn out or incorrect size
  • Motor/drive unit not operating
  • Pump head not properly seated
  • Check and clear tubing; ensure no kinks.
  • Replace tubing; verify correct size.
  • Check motor power and operation.
  • Re-seat pump head securely.
Fluid leakage from pump head
  • Improper tubing installation
  • Damaged or cracked tubing
  • Pump head cover not securely closed
  • Reinstall tubing correctly.
  • Replace damaged tubing.
  • Ensure pump head cover is latched.
Excessive noise during operation
  • Worn rollers or rotor
  • Improper mounting of pump head
  • Tubing rubbing against components
  • Inspect and replace worn parts.
  • Ensure pump head is securely mounted.
  • Adjust tubing position.

6. Specifications

Feature Detail
Brand LEIRONG
Product Type Peristaltic Pump Head
Compatible Tube Types BPT Tube, Silicone Tube
Typical Models/Tube Types BPG BPT tube, BP200-B46, BPG silicone tube, BP200-B30
Application Grades Laboratory, Food, Medical
Weight (approx.) 30g
Origin Mainland China
Package Dimensions (approx.) 10cm (L) x 9cm (W) x 8cm (H)

7. User Tips

  • Tube Selection: Always choose tubing that is chemically compatible with the fluid being pumped and suitable for the required temperature range.
  • Regular Inspection: Periodically check the tubing for signs of wear, especially at the points where the rollers compress it. Early replacement can prevent unexpected failures.
  • Cleanliness: For food and medical applications, ensure strict adherence to cleaning and sterilization protocols for both the pump head and tubing.
  • Motor Compatibility: Ensure the motor/drive unit used with this pump head provides sufficient torque and speed control for your application.

8. Warranty and Support

For any questions regarding the operation, maintenance, or troubleshooting of your LEIRONG Peristaltic Pump Head, please contact the LEIRONG Official Store directly. They can provide specific guidance and information regarding warranty terms and technical support.

Seller: LEIRONG Official Store

© 2023 LEIRONG. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.