1. Introduction
Thank you for choosing the Seauto Crab Cordless Robotic Pool Cleaner. This device is designed to provide reliable, convenient, and cost-effective pool cleaning. Featuring advanced cleaning technology, intelligent navigation, and a cordless design, the Seauto Crab ensures a clean pool with minimal effort.
Its reliable filtration system, active brushing, and full-surface climbing capabilities contribute to maximum pool hygiene. Enjoy swimming with the assurance that your pool is thoroughly clean.
1.1 Warnings and Precautions
Please read these instructions carefully before using the device. We are not responsible for losses or injuries caused by improper use.
- Ensure the device is fully charged before its first use.
- The water depth of the pool must be at least 50 cm (1.6 ft) from the top of the device for optimal cleaning performance.
- The device is equipped with a Lithium battery. Do not disassemble the sealed casing without authorization. Protect the device from direct sunlight and impacts.
- Keep people and animals out of the pool while the device is in operation. Do not leave children unsupervised when the device is in use.
- Turn off the device before cleaning the filters.
- Charge the device once a month during the off-season to preserve battery life.
- Use the pool cleaner only under the following water conditions:
- Chlorine: Maximum 4 PPM
- pH-Value: 7.0 - 7.8 PPM
- Temperature: 41-95 °F (5-35 °C)
- NaCl: Maximum 5000 PPM
2. Product Structure
The Seauto Crab consists of the main pool cleaner unit, a charger, a hook for retrieval, and a filter basket. Refer to the diagrams below for component identification.
Figure 2.1: Seauto Crab Robotic Pool Cleaner Overview
Figure 2.2: Cleaning Patterns (Reciprocal and N-Pattern)
Figure 2.3: Included Components
3. Specifications
| Feature | Specification |
|---|---|
| Applicable Pool Size (Max) | Up to 2150 sq ft (200 m²) |
| Supported Water Depth | 0.5-5 m (1.6-16.4 ft) |
| Charger Input | 100-240 VAC, 50/60 Hz |
| Lithium Battery Capacity | 22.2V / 7800 mAh |
| Battery Lifespan | Up to 150 minutes |
| Charging Time | 3 hours |
| Filter System | 250µm filter basket for regular cleaning |
| Moving Speed | 60 ft/min / 18 m/min |
| Dimensions (L x W x H) | 16.7 x 15.1 x 9.8 inches / 424.7 x 384 x 250.42 mm |
| Net Weight | 19.8 lb / 9 kg |
| Waterproof Level | IP68 |
| Storage Temperature | 32 to 104°F (0 to 40°C) |
| pH Value Supported | 7.0-7.8 |
| Debris Type | Leaves, Algae, Stones, Pollen, Soil, etc. |
| Suction Motor Quantity | 1 |
| Power of Motor | 180W |
| Flow Rate | 80 GPM |
4. Setup
4.1 Initial Charging
Before first use, ensure the Seauto Crab is fully charged. The charging process should be done indoors to prevent damage to the charger, as it is not waterproof or sun-protected.
- Connect the device to the power supply using the provided charger.
- The LED indicator will glow solid red during charging.
- Once fully charged, the LED will turn green and the device will automatically switch off after 10 minutes to protect the battery.
Figure 4.1: App Control Interface (for mode selection)
5. Operating Instructions
5.1 Placement in the Pool
The Seauto Crab operates in a 'Full Protection Mode' by default, cleaning the entire pool, including walls and floor.
- Press the power button on the device to turn it on. The blue light will blink, and you will hear a voice prompt: "Welcome to Seauto Pool Cleaning Robot. I'm ready for work."
- Gently place the device into the pool. Ensure the water surface is above the top of the cleaner for proper operation. The LED indicator will glow solid blue when cleaning begins.
Video 5.1: Product demonstration showing unboxing, features, and in-pool operation.
5.2 Cleaning Modes
The Seauto Crab features advanced navigation technology (SonarNav Pro™) for intelligent path planning and comprehensive pool coverage. You can select different cleaning modes via the app.
To access additional cleaning modes, download the "SEAUTO Unlock" app from Google Play or the App Store. Enable Bluetooth on your phone and the cleaner, ensuring your phone is near the cleaner.
| Mode | Cleaning Coverage | Voice Reminder |
|---|---|---|
| All-cover Mode | Covers all areas (default) | Full-cover Mode |
| Wall-only Mode | Cleans walls only | Wall Mode |
| Floor-only Mode | Cleans floor only | Floor Mode |
Note: Modes can be selected by pressing the switch button. An acoustic signal will indicate the current mode. The default mode upon startup is "All-cover".
Figure 5.2: SonarNav Pro™ Navigation Technology
Figure 5.3: Cleaning Process Overview
5.3 Removal from the Pool
To remove the cleaner from the pool:
- Attach the provided hook to a compatible pole (pole not included).
- Use the pole to hook and retrieve the cleaner from the pool.
- Before cleaning the filter, press and hold the power button to turn off the cleaner.
6. Maintenance
6.1 Cleaning the Filter Basket
It is crucial to clean the filter basket before it dries. Always ensure the cleaner is turned off before performing maintenance.
- Release both sides of the filter basket to open its lid.
- Remove the filter basket from the cleaner.
- Open the lid of the basket.
- Clean the filter basket thoroughly.
- Reassemble the robot after cleaning.
Figure 6.1: Extra-Large 3.5L Basket for Ultra-Fine Filtration
6.2 Battery Replacement
If the performance of the new battery is compromised, allow the cleaner to sit for 2 days before replacement to ensure complete moisture evaporation. Follow these steps to replace the battery and restore optimal cleaning performance:
- Remove the six screws securing the device and carefully take out the used battery.
- Insert the new battery, ensuring the contacts align with those of the old battery.
- Before inserting a new battery, remove any water droplets, sand, or other foreign objects from the connection area.
- Insert, fasten, and secure the screws.
6.3 Off-Season Storage
If the pool cleaner will not be used for an extended period, follow these storage steps:
- Ensure no water remains in the pool cleaner.
- Clean the filter basket thoroughly and reinstall it.
- Store the pool cleaner in a protected location, away from direct sunlight, rain, or frost, at a temperature between 41-113°F (5-45°C).
- Charge the pool cleaner once a month to maintain battery health.
7. Troubleshooting & FAQ
If the suggested solutions do not resolve the issue, please contact customer support.
- Q: What type of pool is suitable?
- A: It is recommended for pools up to 2150 sq ft (200 m²), including in-ground and above-ground pools with flat bottoms. The slope gradient should be less than 90°.
- Q: Why doesn't the cleaner respond after being turned on?
- A: The battery might be low due to long delivery or storage. Please charge the device; the lamp will glow red during charging.
- Q: Why can't it climb walls?
- A1: The device might be set to floor-only mode. Please press the button to select the correct mode.
- A2: There might be too much debris or impurities in the filter basket. You need to remove and clean the basket.
- Q: Why does the cleaner stay on the pool bottom and not move or move slowly?
- A1: It might be caught in the bottom drain. It will try to move itself to get free. If it remains stuck for several minutes, please use the pole to assist it.
- A2: If placed in a very dirty pool, it can pick up a lot of dirt in a short time, which might affect its movement.
- Q: Why does the front part float while the rear part stays on the bottom?
- A: This is an intelligent feature of our pool cleaner to prevent it from getting stuck.
- Q: Why does the cleaner automatically turn off after a few hours of charging?
- A: It is designed to automatically turn off 10 minutes after being fully charged to protect the battery and extend its lifespan. You can leave it charging without worrying about safety.
- Q: What does a yellow light on the cleaner indicate?
- A: A yellow light indicates that the vacuum cleaner has a problem (e.g., overcurrent due to being stuck, or not starting). Remove the vacuum cleaner and restart it; it should then be ready for use again.
- Q: Why does the cleaner show a purple LED while working in the pool?
- A: The cleaner is stuck on an obstacle at the bottom of the pool. Please use the pole to remove the cleaner, restart it, and place it back in the pool.
- Q: Why can't I turn off the cleaner when I take it out of the pool?
- A: This is because water is present in the water detection probe, and the cleaner mistakenly thinks it is still underwater. Wipe the probe clean.
- Q: Are spare parts available, such as wheels or a filter basket with finer filtration?
- A: Please contact your dealer or visit our website for information on replacement accessories and spare parts. The standard filter density is 250µm.
8. User Tips
- To fully utilize all features, download the "SEAUTO Unlock Robot" app. This app is essential for controlling certain functions and is available on Google Play and the App Store.
- When retrieving the cleaner from the pool, use the provided hook attached to a standard pool pole (pole not included).
- The filter is very easy to remove and clean, making maintenance straightforward.
- While the robot generally plans its route automatically, some users have found that occasionally repositioning it can help ensure full coverage, especially if it seems to focus on one area.
- If you experience any Bluetooth connectivity issues with the app, try restarting both the cleaner and your mobile device.
9. Warranty and Support
This product has passed all quality and safety tests conducted by the factory's technical department.
- The warranty period is 12 months from the original purchase date.
- The warranty does not extend to consumable materials (e.g., filter net).
- This warranty is void if the product is modified, misused, or repaired by unauthorized personnel.
- The warranty covers manufacturing defects only and does not cover damage resulting from improper handling by the owner.
- For any warranty claims or repairs, the order number or receipt must be presented.
For questions regarding the warranty, accessories, or consumables, please contact us via email or phone, or visit our website for more information and support.
9.1 Contact Information
Manufacturer: SeautoManufacture Model: Seauto Crab-E
Phone: +1800-618-8968
Email: support@seautorobots.com
Website: https://seautorobots.com
Operating Hours: Mon-Fri, 09:00-18:00 (EST)
Origin: Mainland China
Document Version: 01.007.0062