Dooya DM45R-50/12, DM45S-50/12

Contents

Dooya Tubular Motor DM45R-50/12 & DM45S-50/12 Instruction Manual

Models: DM45R-50/12, DM45S-50/12

Brand: Dooya

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Dooya Tubular Motor, models DM45R-50/12 and DM45S-50/12. These motors are designed for use with rolling blinds, canopies, and electric sunshades. Please read this manual thoroughly before installation and use to ensure safe and efficient operation.

Dooya DM45RM-50/12 Tubular Motor with remote and accessories
Dooya DM45RM-50/12 Tubular Motor with remote control and adapters.

2. Safety Information

This product is a Curtain Motor with a rated voltage of AC 220V~. It has undergone EU conformity assessment and complies with the following directives:

  • Low Voltage Directive 2014/35/EU (LVD)
  • Electromagnetic Compatibility Directive 2014/30/EU (EMC)
  • Restriction of Hazardous Substances Directive 2011/65/EU (RoHS)
  • General Product Safety Regulation (GPSR)

This product meets the requirements of electrical safety, electromagnetic compatibility, and environmental compliance. The EU Declaration of Conformity (DoC) is issued, and technical documentation is kept by the EU Authorized Representative for inspection.

Environmental Note

This product complies with EU RoHS. Do not dispose of it as household waste. Please recycle it in accordance with local regulations for waste electrical and electronic equipment.

3. Product Overview

Model Distinction

The primary distinction between the DM45R and DM45S models lies in their motor line configuration and built-in features:

  • DM45R (Built-in Motor): Features a built-in RF433 receiver and uses a 3-core wire. It does not have an external antenna. This motor can be directly controlled by a wireless switch or wireless remote controller, making it suitable for installations without switch wiring or in small spaces.
  • DM45S (External Motor): This is an external motor that uses a 4-core wire. It does not have a built-in RF433 module and requires an external receiver or switch for remote control functionality.
DM45R-50 vs DM45S-50 motor distinction and wiring diagrams
Comparison of DM45R (built-in, 3-core) and DM45S (external, 4-core) motor wiring.

Components and Accessories

A typical installation for a motorized roller blind includes the tubular motor and several accessories. The motor package typically includes the tubular motor, crown, and drive adapter. Other components like brackets, driving tube, fabric, and bottom beam are usually ordered separately.

Accessories for DM45 Tubular Motor including brackets, drive wheel, crown, tail plug, and tube
Common accessories for DM45 Tubular Motors: Brackets, Drive Wheel, Crown, Tail Plug, and compatible 50mm/55mm Tube (tube sold separately).

4. Specifications

General Specifications

AttributeValue
Brand NameBIAONU
Model NumberDM45R-50/12, DM45S-50/12
Product NameDooya DM45R-50/12 Electric Tubular motor
Voltage230V (Working Voltage: 220/230V, 50/60Hz)
Wattage205W (Power for DM45S-50/12: 205W, Power for DM45R-50/12: 205W)
Rolling Speed / Rotating Speed12r/min
CertificationCE
OriginMainland China
EU LVD VoltageHigh voltage: Above 50Vac or 75Vdc
Battery IncludedNo
High-concerned chemicalNone

DM45 Series Motor Parameter List

Table of DM45 series motor parameters including torque, speed, voltage, current, power, diameter, and length
Detailed parameters for various DM45 series tubular motors.

For DM45S-50/12 and DM45R-50/12 models:

  • Rated Torque: 50Nm
  • Rated Speed: 12r/min
  • Voltage: 220V
  • Rated Current (DM45S): 2.6A
  • Rated Current (DM45R): 0.89A
  • Rated Power: 205W
  • Outer Tube Diameter: 45mm
  • Motor Total Length (DM45S): 514mm
  • Motor Total Length (DM45R): 604mm
DM45S-50/12 motor label with specifications
DM45S-50/12 motor label showing specifications like torque, speed, voltage, current, power, and IP44 rating.

5. Setup Instructions

Installation Overview

The installation of the tubular motor involves mounting the motor within a driving tube, securing it with brackets, and connecting it to power and control systems. Ensure all components are compatible and securely fastened.

Diagram showing the solution for motorized roller blinds with components like tubular motor, drive adapter, idler bracket, wall bracket, driving tube, fabric, and bottom beam.
Solution for Motorized Roller Blinds: Illustrates the placement of the tubular motor, drive adapter, idler bracket, wall bracket, driving tube, fabric, and bottom beam.

Wiring Instructions

Proper wiring is crucial for the safe and correct operation of the motor. Refer to the diagrams below for guidance.

  • DM45R (Built-in Motor, 3-core wire): Connect the Blue wire to the zero line, the Brown wire to the Fire Wire, and the Yellow/Green wire to the ground wire.
  • DM45S (External Motor, 4-core wire): Connect the Blue wire to the zero line, the Brown wire to Fire Wire 1, the Black wire to Fire Wire 2, and the Yellow/Green wire to the ground wire.
Built-in motor with 3-core wire (Blue, Brown, Yellow/Green)
Built-in Motor (DM45R) with 3-core wire connection.
External motor with 4-core wire (Blue, Brown, Black, Yellow/Green)
External Motor (DM45S) with 4-core wire connection.

Motor Application Notes

AC tubular motors are categorized into external and built-in types. For external motors, 220V AC power is supplied to the switch, and then a 3-wire connection goes to the motor (2 Fire Wires, 1 Zero Line). This setup allows for mechanical manual switch control with up, down, and stop functions.

External motors can also be equipped with a receiver and used with a remote control. This provides flexible control options. Built-in motors have an internal receiver, allowing direct control via remote or wireless switch without external wiring for the receiver.

Motor application notes showing wiring for external tubular motor with mechanical switch and with receiver switch
Motor application notes: External tubular motor wiring for mechanical hand switch and with receiver switch (DC305 remote, DC254 switch).

Limit Adjustment

The motor features a stroke adjustment mechanism to set the upper and lower limits of the blind's travel. This is typically done using a stroke adjustment rod (often green) inserted into the motor head. Refer to the motor's specific instructions for precise adjustment steps.

Close-up of motor end with limit adjustment screws
Close-up view of the motor end, showing the limit adjustment points.

6. Operating Instructions

Basic Operation

Once installed and powered, the motor can be operated to move the blinds or sunshade up, down, or stop at any desired position.

  • Up/Open: Press the 'Up' button on your remote or switch.
  • Down/Close: Press the 'Down' button on your remote or switch.
  • Stop: Press the 'Stop' button to halt movement at any point.

Remote Control and Pairing

For DM45R motors, which have a built-in RF433 receiver, a compatible RF433 remote controller (e.g., DC1650) or wall switch (e.g., DC863, DC305) is used for control. New rolling code motors require pairing with the rolling code remote control before first use. Specific pairing instructions are typically provided with the remote control unit.

Built-in motor diagram with wireless switch DC863 and remote DC305
Built-in tubular motor directly connected to power, controlled by wireless switch (DC863) or remote (DC305).

For DM45S motors, external controllers such as DC227A, DC228A, or Tuya WiFi curtain wall switches can be used. These external controllers allow for simultaneous control via wall switch and remote controller.

7. Maintenance

To ensure the longevity and optimal performance of your tubular motor, follow these general maintenance guidelines:

  • Keep Clean: Periodically clean the motor and surrounding area to prevent dust and debris buildup, which can affect performance.
  • Avoid Obstructions: Ensure that the path of the blinds or sunshade is free from any obstructions that could strain the motor.
  • Regular Checks: Occasionally check the mounting brackets and connections for any signs of loosening or wear. Tighten as necessary.
  • Professional Service: For any complex issues or internal repairs, contact a qualified technician. Do not attempt to disassemble the motor yourself.

8. Troubleshooting

If you encounter issues with your tubular motor, consider the following common problems and solutions:

  • Motor Not Responding: Check the power supply and all wiring connections. Ensure the remote control batteries are functional and the motor is properly paired with the remote.
  • Limits Not Setting Correctly: Re-check the limit adjustment procedure as per the motor's specific instructions. Ensure the adjustment rod is fully engaged.
  • Unusual Noises During Operation: Inspect the blind or sunshade mechanism for any obstructions or misalignments that might be causing friction. Ensure the motor is securely mounted.
  • Intermittent Operation: This could indicate a loose connection, interference with the RF signal (for DM45R), or an issue with the control unit. Verify connections and try operating from a closer distance.

If problems persist after basic troubleshooting, please contact customer support.

9. User Tips

  • Always read the user manual carefully before using the motor for the first time to familiarize yourself with its features and safety guidelines.
  • When selecting a motor, ensure compatibility with your specific tube type (e.g., 50mm Round Tube, 60mm Octagonal, 90mm Groove Tube) and control system requirements (RF433 remote or external switch).
  • If you have any questions or encounter issues, it is recommended to contact customer support for assistance to ensure the best possible solution.

10. Warranty and Support

This product is manufactured by Lumi United Technology Co., Ltd. and complies with relevant EU directives for safety and environmental standards. A detailed user manual (PDF) is available for further reference.

Manufacturer Information

Name: Lumi United Technology Co., Ltd.
Address: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China
Tel: 86-18589043609

EU Authorized Representative

Name: Sophie Bennett
Address: 9 rue du Bat d'Argent, 69001 Lyon, France
Tel: 33-774555006

For support or inquiries, please contact the manufacturer or your local distributor.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.