TDD Lexus IS Steering Wheel

Contents

TDD Lexus IS Carbon Fiber Perforated Leather Steering Wheel

Model: Lexus IS Steering Wheel | Brand: TDD

Introduction

Thank you for choosing the TDD Carbon Fiber Perforated Leather Steering Wheel for your Lexus IS. This manual provides essential information for the proper installation, operation, and maintenance of your new steering wheel. Please read it thoroughly before proceeding with any steps.

Installed TDD carbon fiber steering wheel in a Lexus IS interior.
The TDD carbon fiber steering wheel seamlessly integrated into a Lexus IS vehicle.

Setup and Installation

Important Safety Note: Steering wheel replacement involves working with the vehicle's airbag system. Improper installation can lead to serious injury or malfunction. It is highly recommended that installation be performed by a qualified professional.

This product is the steering wheel frame and covering only. It does NOT include the airbag, trims, switches, or other electronic components. These parts must be carefully transferred from your original steering wheel.

Pre-Installation Checklist:

  • Ensure your vehicle is turned off and the battery is disconnected to prevent accidental airbag deployment.
  • Gather necessary tools (e.g., Torx bits, socket wrenches, trim removal tools).
  • Review your vehicle's specific service manual for detailed instructions on removing the original steering wheel.

Installation Steps (General Guide):

  1. Disconnect Battery: Disconnect the negative terminal of your car battery and wait at least 10-15 minutes to allow the airbag system to discharge.
  2. Remove Airbag Module: Carefully follow your vehicle's service manual to safely remove the airbag module from your original steering wheel.
  3. Disconnect Wiring: Disconnect all electrical connectors for the airbag, horn, and steering wheel controls.
  4. Remove Steering Wheel: Use a suitable socket wrench to remove the central nut securing the steering wheel to the steering column. Mark the steering wheel's position relative to the column to ensure proper alignment during reinstallation.
  5. Transfer Components: Transfer the airbag module, steering wheel controls, paddle shifters (if applicable), and any decorative trims from your original steering wheel to the new TDD steering wheel. Ensure all components are securely fastened.
  6. Install New Steering Wheel: Align the new TDD steering wheel with the marks made on the steering column and slide it into place. Secure it with the central nut, tightening to the manufacturer's specified torque.
  7. Reconnect Wiring: Reconnect all electrical connectors for the steering wheel controls, horn, and finally, the airbag module.
  8. Reconnect Battery: Reconnect the negative terminal of your car battery.
  9. Test Functionality: Turn on your vehicle and test all steering wheel functions (horn, controls, paddle shifters) and ensure no airbag warning lights are illuminated.
Rear view of the TDD steering wheel frame, showing mounting points.
The rear structure of the steering wheel, highlighting the mounting brackets and internal components.
Front view of the TDD steering wheel frame, ready for installation.
The front view of the steering wheel frame, illustrating its ergonomic design before final assembly.

Operating Instructions

The TDD Carbon Fiber Perforated Leather Steering Wheel operates identically to your vehicle's original steering wheel once installed. All transferred controls (horn, audio, cruise control, paddle shifters, etc.) will function as before.

  • Steering: Use the steering wheel to control the direction of your vehicle.
  • Controls: Utilize the integrated buttons and switches for various vehicle functions as per your Lexus IS owner's manual.
  • Paddle Shifters (if applicable): Operate the paddle shifters for manual gear selection if your vehicle is equipped with this feature.

Maintenance and Care

To ensure the longevity and appearance of your TDD steering wheel, follow these care guidelines:

  • Cleaning Carbon Fiber: Wipe carbon fiber surfaces with a soft, damp cloth. Avoid abrasive cleaners or harsh chemicals that could damage the clear coat.
  • Cleaning Leather: For perforated leather sections, use a dedicated automotive leather cleaner and conditioner. Apply sparingly to a microfiber cloth and gently wipe the surface. Do not saturate the leather.
  • Avoid Direct Sunlight: Prolonged exposure to direct sunlight can cause fading or cracking of materials. Consider using a sunshade when parking for extended periods.
  • Avoid Harsh Chemicals: Do not use household cleaners, solvents, or silicone-based products on the steering wheel, as these can degrade the materials.

Troubleshooting

If you encounter any issues after installing your TDD steering wheel, consider the following:

  • Airbag Warning Light: If the airbag warning light illuminates after installation, immediately stop driving and consult a professional mechanic. This indicates an issue with the airbag system. Recheck all airbag connections.
  • Controls Not Functioning: Ensure all electrical connectors from the original steering wheel were properly reconnected to the new steering wheel's components. Check for any pinched or damaged wires.
  • Steering Wheel Not Straight: If the steering wheel is not centered when driving straight, it may have been installed incorrectly on the steering column spline. Re-align the steering wheel carefully.
  • Fit Issues: The steering wheel is designed to OE specifications. If you experience significant fit issues, double-check that the correct model was ordered for your Lexus IS. Contact customer support with photos if necessary.
  • Color Discrepancy: Due to variations in monitor settings and lighting, the color of the product may appear slightly different in person. If you believe there is a significant color error, contact customer support.

Specifications

FeatureDetail
Brand NameTDD
MaterialCarbon Fiber, Perforated Leather, ABS/Plastic
Carbon Fiber Standard3K 240g
Construction Layers6 Resin Layers, Carbon Fiber, ABS/Plastic
OriginMainland China
Package Length43 cm
Package Width42 cm
Package Height19 cm
Package Weight3.5 kg
Diagram showing the layers of real carbon fiber construction: 6 resin layers, carbon fiber, ABS/Plastic.
Detailed diagram illustrating the multi-layered construction of the steering wheel, emphasizing the use of real carbon fiber and eco-friendly resin.
Images showing solid, light, soft, and durable properties of carbon fiber, and a diagram of real carbon fiber layers from Japan.
Visual representation of carbon fiber properties (solid, light, soft, durable) and a diagram detailing the construction with real carbon fiber from Japan.

Warranty and Support

Warranty:

The product comes with a 12-month free maintenance warranty. If parts need to be replaced during this period, the buyer is responsible for the cost of the parts and shipping.

Returns:

Returns are accepted within 15 days of receipt if the item is in its original condition. The buyer is responsible for return shipping costs. If the item is damaged during return shipping, the buyer should file a claim with the logistics company.

Customer Support:

For any questions, concerns, or issues, please contact the TDD Official Store directly. Providing detailed information and photos can help expedite the support process.

Text detailing return, warranty, feedback, size, and color policies.
Important information regarding returns, 1-year warranty, feedback guidelines, and notes on size and color variations.

User Tips

  • Professional Installation: Given the complexity of transferring components and the safety implications of the airbag system, professional installation is strongly recommended.
  • Customization Options: TDD offers multiple customization options for carbon fiber types, leather colors, and stitching colors. Ensure you confirm your desired specifications before ordering.
  • Component Transfer: Remember that only the steering wheel itself is provided. All functional components like the airbag, buttons, and trims must be transferred from your original steering wheel.
TDD carbon fiber steering wheel with red perforated leather grips.
A variant of the TDD steering wheel featuring red perforated leather for enhanced grip and aesthetics.
Diagram showing various color options for steering wheel stripes and perforated leather sections.
Visual guide for available color customizations for the steering wheel's stripe and perforated leather areas. Carbon fiber is only available in black color. Colors other than black are glass fiber.
Examples of different carbon fiber weave patterns: Classic, Honeycomb, Forged, Smooth.
Visual examples of various carbon fiber types available for customization, including Classic, Honeycomb, Forged, and Smooth patterns.
Color chart displaying a wide range of stitching thread color options.
A comprehensive chart showcasing the numerous stitching color options available for personalizing the steering wheel.
Swatches of various leather types and colors, including Italian Suede, Micro-Fiber, Lichi Texture, Smooth, Perforated, and Nappa leather.
A selection of leather material options, including Italian Suede, Micro-Fiber, Lichi Texture, Smooth, Perforated, and Nappa leather, highlighting their tactile qualities.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.