Introduction
This manual provides detailed instructions for the safe and efficient operation of your Radtel RT-880G Ham Radio. Please read this manual thoroughly before using the device to ensure proper functionality and to prevent damage.
The Radtel RT-880G is a versatile multi-band ham radio featuring APRS, GPS, 10W RF power, 1024 channels, and reception capabilities across AM, USB, LSB, CW, CB, HF, UHF, VHF, LW, MW, SW, and SSB bands. It also includes a cross-band repeater function and a 2.4-inch TFT HD large color screen display.
Familiarization with Your Radio
Radio Overview
The following diagram identifies the main components of your Radtel RT-880G radio:

This image displays the front, side, and top views of the radio with numbered labels for each part, along with a list of included accessories.
- Antenna
- PTT (Push-To-Talk) Button
- Side-key 1
- Side-key 2
- Battery
- SW/MW/LW FM antenna (Channel knob)
- ON/OFF volume
- Indicator Light
- Alarm Button
- Display screen
- Keypad
- MIC
- Speaker
- Ear/Mic jack
- Type C charging port/programmable jack
Antenna Ports and LED Indicator

This image highlights the two antenna ports and the power/volume adjustment knob at the top of the radio.
- Antenna Port 1: Used for all frequency transmission and reception except short wave/middle wave/long wave/FM radio frequencies.
- Antenna Port 2: Used for short wave/middle wave/long wave/FM radio frequencies.
- Power Button/Volume Adjustment: Used to turn the device on/off and adjust the volume.
- Emergency Alarm Button/Customizable Button: Can be used for emergency alarms or customized functions.
- LED Light:
- Green Light: Indicates the device is receiving a signal.
- Red Light: Indicates the device is transmitting a signal.
Setup
Charging the Radio
Your RT-880G radio supports three charging methods:

The radio can be charged using a Type-C cable (from car, PC, power bank, or wall socket) or via the included desk charger.
- Charging with the Radio in the Charging Dock:
- Insert the battery into the radio.
- Place the radio into the charging dock.
- Ensure the radio is properly seated in the charger.
- Charging the Battery Alone in the Charging Dock:
- Remove the battery from the radio.
- Insert the battery into the charging dock.
- Make sure the battery is aligned correctly.
- Charging via USB-C Cable:
- Plug a USB-C cable into the charging port on the side of the radio.
- Connect the other end of the cable to a power adapter, computer, or power bank.
LED Indicator Status during Charging:
- Red Light: Charging in progress.
- Green Light: Charging complete.
Note: Use only recommended chargers and cables. Do not charge in extreme temperatures. Fully charge the battery before first use for optimal performance. Do not use cell phone fast chargers for this radio.
Initial Frequency Setup
The device operates in three frequency ranges: 64-620 MHz, 18-64 MHz, and 840-1000 MHz. Transmission and reception for all three bands are handled via the left main antenna port.
To change the frequency band, navigate to [Basic Settings] → [17 Work Range] in the menu. After selecting the desired frequency band and confirming, the device will restart.
Important: Ensure that you replace the antenna with one that matches the selected frequency band. Using an incorrect antenna may result in damage due to frequency mismatch.
Operating Instructions
Keypad Functions
The keypad provides various functions for controlling the radio:
| Key | Function |
|---|---|
| PTT | Transmit or Exit |
| Alert Key | Definable long press (L) and short press (S) functions |
| Side Key 1 | Can be set as PTT-2 for transmission (disables custom function). Also has definable long and short press functions. |
| Side Key 2 | Can be set as PTT-3 for transmission (disables custom function). Also has definable long and short press functions. |
| Menu/OK | Short press to confirm or enter into menu. Long press to enter DTMF inputting (standby) or exit menu interface. |
| Up Arrow | Move up; long press to quickly scroll up. DTMF :B |
| Down Arrow | Move down; long press to quickly scroll down. DTMF :C |
| Exit/Cancel | Short press: Switch ABC channels, exit menu, cancel operation. DTMF :C |
| 0 | Short press: Enter number 0. Long press for definable functions or switch scanning direction in FM RADIO mode. DTMF :0. To input Number 0 or Space Bar. |
| 1 | Short press: Enter number 1. Long press for definable functions. DTMF :1. To input Number 1/English Letters/Chinese Characters. |
| 2-9 | Short press: Enter numbers 2-9. Long press for definable functions. DTMF :2-9. To input Number 2-9/English Letters/Chinese Pinyin Codes. |
| * | Short press: Switch between channel frequency/number/alias, move cursor in FM RADIO mode. Long press to lock keypad. DTMF :*. Text input: Delete text. |
| # | Short press: Switch working mode (VFO/channel/zone). Or switch short wave modulation in FM RADIO. Long press: Jump to transmit frequency input menu. Or switch short wave mode in FM RADIO. DTMF :# . Text input: Enable/disable text input, switch text input method. |
LCD Display
The 2.4-inch TFT HD large color screen displays various information and indicators:

The display shows channel aliases, VFO mode, and frequency information, along with battery status and signal strength.
Key indicators include:
- Keyboard Lock, Prompt Tone, Scan, RR (Talk around)/TR (Reverse Frequency), Multi-Frequency Standby, VOX, GPS (option function), Cross-Band Repeater, Battery Icon, Multi-PTT Enable, Received Signal Strength, Received Signal Field Strength Value, High Power / Low Power switchable, CTCSS / DCS / MUT Non-standard DCS / ENC Encrypted DCS, Wide or Narrow Bandwidth, FM/AM RX, Channel Number (CH-XXXX), Zone Number (ZONE-XXX), Working Frequency / Working Channel, Main Frequency Area Indicator Icon, Channel Name, Working Frequency Range, A/B/C Main Frequency Area, Received Signal Meter.
Basic Operation
Frequency Input
- Switch to VFO Frequency Mode: Press the # key to enter VFO Frequency Mode.
- Enter the Frequency: Use the numeric keypad to input the desired frequency. The input must be either 6 digits or 8 digits, depending on the selected setting.
- Frequency Input Settings: Navigate to [Basic Settings] → [Frequency Input 30]. Select [6 Bits] for 6-digit input or [8 Bits] for 8-digit input.
Repeater Frequency Input
Method 1: Using Offset Frequency Settings
- Navigate to [CH Settings] → [16 Offset Freq] and use the numeric keypad to input the offset frequency.
- Go to [CH Settings] → [15 Offset Direction] and select either positive or negative offset.
Method 2: Direct Transmit Frequency Input
- In standby mode, long press the [#V/M] key to enter the [Transmit Frequency] menu.
- Use the numeric keypad to enter the desired transmit frequency, then press OK to confirm.
- Go to [CH Settings] to access the sub-audio settings menu and configure the sub-audio frequency as needed.
Transmitting and Receiving Signals
- Standard Transmission: Press the PTT key to initiate a call. The LED indicator will turn red.
- Multi-PTT Mode: If enabled ([Key Definition] → [1 Multi-PTT]), Side Key 1 transmits on Band B, and Side Key 2 transmits on Band C. Shortcut functions of Side Key 1 and 2 are disabled in this mode.
- Receiving Signals: The LED indicator turns green. Audio is enabled if no sub-audio (CTC/DCS) is set, or if the received sub-audio matches the configured sub-audio.
CTCSS/DCS Settings
Navigate to [CH Settings] to set the sub tone CTCSS or DCS.
- CTC/DCS (Transmit & Receive): Enables both transmit and receive CTC/DCS. Communicates only with matching signals.
- RX CTC/DCS (Receive Only): Accepts signals matching the set CTC/DCS code; transmission is unrestricted.
- TX CTC/DCS (Transmit Only): Transmits using the set CTC/DCS code; receives all incoming signals without restriction.
U/V Cross-Band Repeater

The radio can transfer UV cross-band and UU same-frequency inter-transfer, for example, UHF transmitting to VHF.
Activating Cross-Band Repeater Mode: Assign a button to [26 UV Repeater] or enable via [Basic Settings] → [28 UV Repeater].
Once activated:
- Channel C is disabled.
- Only Channels A and B are used for cross-band repeating.
- Signals received on Channel A are retransmitted on Channel B.
- Signals received on Channel B are retransmitted on Channel A.
Monitoring Repeater Audio: Enable [29 Repeater Monitor] in [Basic Settings] to listen to repeater voice communications.
DTMF Function
- Accessing DTMF Input Mode: In standby mode, long press the Menu/OK key to enter the DTMF input interface.
- Entering DTMF Codes: Use the numeric keypad. Short press Side Key 2 to delete the last entered digit.
- Transmitting DTMF Codes: Press the PTT key. The device sends the DTMF code after a preset delay.
- DTMF Decoding: When enabled, received DTMF codes are displayed on screen.
- DTMF Transmission in Analog Mode: Pressing a key on the keypad sends the corresponding DTMF code.
- DTMF Remote Monitoring: Set a DTMF monitoring code and enable [Accept Remote Control]. Another radio sending this code will cause the device to transmit for 60 seconds.
- DTMF Remote Stun/Kill/Wake: Set a remote stun/kill/wake code and enable [Accept Remote Control]. Another radio can send this code to stun (cannot transmit/operate keypad, but receives), kill (inoperable until wake code), or wake the device. Important: Always set a wake code before enabling stun/kill.
Text Input Function
- In the Text Input Menu, use the # key to switch input methods and the * key to delete text or pinyin.
- Number Input [123]: Use numeric keypad.
- English Input [AB] / [abc]: Keys 2-9 for letters, 0 for space, 1 for symbols. Press a key multiple times to cycle through letters.
- Chinese Pinyin Input [PY1] / [PY2]: Enter pinyin using numeric keypad, use arrow keys to select characters, and press the Menu/OK key to confirm.
FM Radio & Shortwave Receiver
- Defining the FM Radio Trigger: Assign a button for the FM Radio function via Menu → Key Define. Pressing the button enters radio mode; pressing PTT exits.
- Switching Between Radio Bands: Long press the # key to switch between USW (64-108 MHz), SW (2.0-30.0 MHz), MW (520-1710 KHz), LW (153-279 KHz).
- Switching Demodulation Modes: Short press the # key. USW band is fixed to FM. Other bands can switch between AM, USB, LSB, CW.
- NOAA Weather Forecast Frequencies: The radio can access 11 NOAA weather forecast frequencies (e.g., 162.550, 162.400, etc.).
One-Key Frequency Measurement & Remote Sub-Audio CTCSS/DCS Decoding
- Press the trigger button to enter Frequency Measurement or Remote Sub-Audio Decoding Mode.
- Press the * key to switch between modes.
- During frequency measurement, press PTT or exit key to exit. Press # to switch frequency band.
- After measurement, press exit to re-measure, or menu key to save to VFO channel. Press PTT to transmit.
Spectrum Scanning
This video demonstrates the GPS, APRS position transmission, shortwave reception, and spectrum functions of the Radtel RT-880G.
- Press the trigger button to enter Spectrum Scanning Mode. Press * to exit.
- Short press * to switch input fields. The display shows Scan Center Frequency, SPACE (scan step size), DECAY (signal amplitude attenuation).
- Use arrow keys to move the indicator cursor. The bottom display shows Frequency, RSSI, NOISE, and GLITCH.
GPS Functionality
The RT-880G includes GPS for positioning and tracking:
- GPS Positioning: Displays Longitude, Latitude, Altitude, Speed, Callsign, and current time.
- Standalone Distance Measurement: After GPS lock, set a starting point (briefly press Menu key). After moving, briefly press # key to get current distance and direction relative to the start point.
- Two RT-880G Devices: Can send GPS coordinates to each other via end-of-transmission tone. The receiving unit displays distance and direction.
- GPS Track Recording and Querying: Record latitude and longitude manually or at timed intervals. View track points, distance, and direction relative to current location.
- GPS Settings: Turn on/off GPS background reception, set GPS Baudrate, UTC Zone, PC Monitor (upload data to PC via programming cable), Coordinate Type, Speed Unit, Distance Unit, Altitude Unit, Fixed Latitude/Longitude/Altitude, Mileage, Mileage Type, Clear Mileage, Manual Record, GPS Auto Record, GPS Record Time, Query Track, Clear Track.
APRS Functionality
The radio supports APRS for transmitting and decoding position information:
- APRS Hardware Encoding/Decoding: Transmit device's APRS info to other units, and decode incoming APRS data. If received data includes GPS coordinates, the device calculates direction and distance to the other unit.
- APRS Data Transmission to PC: APRS data can be reported to a PC via a programming cable for internet forwarding.
- APRS Settings: Turn on/off APRS function, Station Mode (dynamic GPS or fixed coordinates), Beacon Setup, Call Sign, SSID, Symbol Table, Symbol, Comment, MIC-E On-off, MIC-E Mode, Path 1, Path 1 Count, Path 2, Path 2 Count, TX Voltage, TX Star Count, TX Mileage, Beacon Mode, PTT After, Smart Mode, Time Mode, Timed Time(S), Queue Mode, Queue Interval, DIGI SETUP, DIGI REP CH, DIGI1 On/Name, DIGI2 On/Name, Wait Before REP, Remote Password, APRS RX CH, APRS TX CH, TX Level, RX Level, Demod Tone.
Maintenance
- Always use the ON/OFF control to power the device.
- Do not transmit with a damaged antenna.
- Avoid prolonged transmission.
- Do not touch the antenna or any part of your body when transmitting.
- If malfunction (burnt scent, smoke) occurs, immediately turn off the device, disconnect the charger, and consult Technical Service.
- Do not introduce objects into the speaker holes or transceiver connectors.
- If using an external headset, reduce volume to avoid very high audio levels.
- Protect the equipment and battery charger from water, direct sunlight, heat sources, dust, dirt, fire, or explosive conditions.
- Do not store the transceiver in a vehicle parked in direct sunlight.
- Avoid humidity condensation. If condensation occurs, clean with a dry cloth and allow to dry completely.
- Do not place anything on the transceiver that can spill.
- To clean, ensure the equipment and battery charger are OFF. Use an antistatic cloth (preferably) or a humid (not wet) cloth.
- Do not spray liquids or cleaning products directly on the transceiver, battery pack, or charger. Avoid polish, detergents, alcohol, or solvent.
- Do not use a dry cloth for cleaning, as it could cause static shock.
Troubleshooting Guide
| Problem | Possible Cause | Solution |
|---|---|---|
| No power on | Battery is dead or not inserted properly | Check battery charge and connection |
| No Transmission | PTT (Push-To-Talk) button not pressed or faulty | Ensure PTT is pressed; check for damage |
| Poor Audio Quality | Weak signal or interference | Move to a clear area; adjust antenna |
| Short Battery Life | Old battery or high power usage | Replace battery; use power-saving mode |
| Cannot Receive Signal | Wrong channel or squelch level set | Verify channel settings; adjust squelch |
| Distorted Sound | Volume too high or speaker clogged | Lower volume; clean speaker grille |
| Overheating | Prolonged transmission or faulty unit | Allow cooldown; check ventilation |
| Stuck in One Channel | Lock feature enabled | Disable channel lock function |
| The radio keeps transmitting | VOX may be turned on or the squelch level is too sensitive | Turn off VOX or adjust squelch level |
If these solutions do not resolve your issue, please contact technical support.
Technical Specifications

This image provides a table of detailed technical specifications for the RT-880G.
| General | |
|---|---|
| Frequency Range | Radio: FM 64-108MHz, SW 2.3-30MHz, MW 520-1710KHz, LW 153-279KHz RX: 18-620MHz, 840-1000MHz TX: 18-32MHz, 136-174MHz, 400-520MHz |
| Channel Capacity | 1024 Channels + 3*VFO Channels |
| Channel Spacing (W/N) | Analog: 25kHz/12.5kHz, Digital: 12.5K |
| Voltage | 7.4V DC |
| Working Mode | Same frequency simplex, different frequency simplex |
| Antenna | Removable Antenna |
| Frequency Stability | ±2.5ppm |
| Working Temperature | -20℃ ~ +60℃ |
| Dimension | 149 * 64 * 37 mm (Antenna is not included) |
| Weight | About 307g |
| Receiving Part | |
| Modulation Mode | F3E |
| Maximum Frequency deviation (W/N) | ≤5KHz / ≤2.5KHz |
| RX Current | ≤350mA |
| Standby current | ≤100mA |
| Transmitting Part | |
| Output Power (UHF/VHF) | ≤10W |
| TX Current | ≤2500mA |
| Sensitivity (W/N) | 0.22μV / 0.25µV (12dB SINAD) |
| Inter modulation (W/N) | 65dB / 60dB |
| Audio Distortion | <5% |
| Audio Output Power | ≤1W (16Ω) |
Note: Specifications may change due to technical improvements without prior notice or liability.
User Tips
- Performance: The radio offers very good sensitivity and sufficient power, even if it doesn't always reach the full 10 watts.
- Build Quality: Users report neat workmanship and a good feel.
- Troubleshooting: If you encounter any issues, the seller is noted for being responsive and helpful in resolving problems.
- SSB on VHF/UHF: The radio supports SSB on HF, UHF, and VHF bands.
- Included Accessories: The package typically includes the main unit, antenna, battery, back clip, charger, and instruction manual.
Warranty and Support
FCC Warning and Compliance
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this equipment causes harmful interference to radio or television reception, try reorienting the receiving antenna, increasing separation, or connecting the equipment to a different circuit. Consult the dealer or an experienced radio/TV technician for help.
Safety Information for Radios
Your portable transceiver contains a low power transmitter. When the talk button is pushed, it sends out radio frequency (RF) signals. The device is authorized to operate at a duty factor not to exceed 50%. The FCC adopted RF exposure guidelines with safety levels for handheld wireless devices. For body-worn operation, this radio has been tested and meets the FCC RF exposure guidelines when used with accessories supplied or designated for this product. Use of other accessories may not ensure compliance. Use only the supplied antenna. Unauthorized antennas, modifications or attachments could damage the transmitter and may violate FCC regulations.
Normal Position: Hold the transmitter approximately 25 mm from your face and speak in a normal voice, with the antenna pointed up and away.
Local Government Regulations
When two-way radios are used as a consequence of employment, Local Government Regulations require users to be fully aware of and able to control their exposure to meet occupational requirements. Your Radtel two-way radio has an RF Exposure Product Label. Your user manual or separate safety booklet includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements.
CE Marking
The CE marking indicates that Xiamen Radtel Electronics Co.,Ltd declares that the radio equipment type is in compliance with the RED Directive 2014/53/EU, ROHS Directive 2011/65/EU, and WEEE Directive 2012/19/EU. The full text of the EU declaration of conformity is available in this manual or at www.radtel.com.
Important Warnings
- Only use this equipment for its intended purpose. The manufacturer and salesperson will not accept responsibility, and the guarantee will be invalidated, in the event of inadequate use.
- This equipment does not have user-repairable components. Always consult an Authorized Technical Service for any repair.
- Explosion risk if the battery pack is replaced with an incompatible one.
For further support, please contact support@radtel.com or visit www.radtel.com.