ALLMATIC YNG800

Contents

ALLMATIC Universal Garage Door Opener Remote Control

Model: YNG800

1. Introduction

This manual provides detailed instructions for the ALLMATIC YNG800 universal garage door opener remote control. This device is designed to duplicate existing ALLMATIC rolling code remotes, offering a convenient solution for controlling garage doors, gates, and barriers. It operates at a frequency of 433.92MHz and supports both 2-button and 4-button configurations.

Multiple views of the ALLMATIC YNG800 remote control, showing front, back, side with clip, and top views.

Figure 1: Views of the ALLMATIC YNG800 Remote Control

2. Specifications

FeatureDescription
Model NumberYNG800
Frequency433.92MHz
Encoding MethodRolling Code
Buttons2 or 4
BatteryIncluded
OriginMainland China
CertificationCE, FCC, RoHS, WEEE

Compatible ALLMATIC Models:

  • ALLMATIC FOR4
  • ALLMATIC TECH 3
  • ALLMATIC BRO OVER
  • ALLMATIC MINI PASS
  • ALLMATIC B.RO 1WN
  • ALLMATIC B.RO 2WN
  • ALLMATIC B.RO 4WN
  • ALLMATIC B.RO 1WN RED
  • ALLMATIC B.RO 2WN RED
  • ALLMATIC B.RO 4WN RED
Image showing various ALLMATIC remote controls and the universal remote, indicating compatibility.

Figure 2: Compatible ALLMATIC Remote Controls

3. Setup and Programming

The ALLMATIC YNG800 remote control can duplicate both fixed and rolling codes. Ensure you have access to your receiver/opener before starting the programming process.

3.1. Fixed Code Duplicating Procedures

  1. While pressing button 1, press button 2 four times.
  2. Release both buttons. The LED on the new remote will emit a quick flash every 2 seconds.
  3. Place the original remote control in front of the new remote, at a distance of about 4-60 cm.
  4. Press and hold the button on the original remote control that you wish to copy. Continue holding until the new remote's LED changes its flashing frequency (faster than before), confirming a successful code copy.
  5. While the LED is flashing rapidly, press the corresponding button on the new remote where you want to store the copied code, until the LED turns off.
  6. The copy process is complete.
Diagram illustrating the fixed code programming steps.

Figure 3: Fixed Code Programming Diagram

3.2. Rolling Code Duplicating Procedures

  1. While pressing button 1, press button 2 four times.
  2. Release both buttons. The LED on the new remote will emit a quick flash every 2 seconds.
  3. Place the original remote control in front of the new remote, at a distance of about 4-60 cm.
  4. Press and hold the button on the original remote control that you wish to copy. Continue holding until the new remote's LED turns on with a steady light and then emits a double flash every 2 seconds.
  5. Transmit the seed code of the original remote control by pressing the rear hide button or buttons 1 and 2 simultaneously on the new remote.
  6. Now the LED will flash quickly. Press the button on the new remote where you want to store the copied code until the LED turns off.
  7. Activate the procedure to insert the new remote control on the receiver.
Diagram illustrating the rolling code programming steps.

Figure 4: Rolling Code Programming Diagram

3.3. Auto Matching Code

  1. Ensure you are close to the automation system.
  2. Press and hold the programmed button on the new remote for about 10 seconds. When the LED starts to flash, release the button.
  3. Wait until the LED turns off. The operation is complete, and you can now use your new remote control.

To activate other models on the receiver, refer to the instructions of the original model.

NOTE: The seed code can be emitted as follows:

  1. Press buttons 1 and 2 simultaneously for 8 seconds and release them when the LED starts to flash.
  2. While the LED is flashing, press the button corresponding to the needed seed code.
Diagram showing two remote controls side-by-side for cloning, with 'button1' and 'button2' indicated.

Figure 5: Remote Control Button Layout for Programming

3.4. Programming Demonstration Video

Video 1: Step-by-step demonstration of the remote control programming process.

4. Operation

Once successfully programmed, your ALLMATIC YNG800 remote control can operate up to four different doors or functions, depending on the number of buttons on your model and how you've programmed them.

  • Garage Door: Typically assigned to Button 1.
  • Gate Door: Typically assigned to Button 2.
  • Barrier: Can be assigned to Button 3.
  • Sliding Gate: Can be assigned to Button 4.

Simply press the corresponding button to activate the desired function.

Diagram showing how one remote control can operate four different types of doors: garage door, gate door, barrier, and sliding gate.

Figure 6: One Remote Control, Four Doors Functionality

The remote control clipped to a car visor for easy access.

Figure 7: Remote Control with Car Visor Clip

5. Maintenance

  • Battery Replacement: The remote control includes a battery. If the remote's LED does not light up or is dim when a button is pressed, the battery may need replacement. Refer to the device's internal design for battery access.
  • Cleaning: Wipe the remote control with a soft, dry cloth. Avoid using harsh chemicals or abrasive cleaners.
  • Storage: Store the remote in a dry place, away from direct sunlight and extreme temperatures.
  • Water Exposure: This device is not waterproof. Avoid exposure to water or high humidity.

6. Troubleshooting

  • Remote not programming:
    • Ensure the original remote control is functioning correctly.
    • Verify the distance between the original and new remote is within 4-60 cm during programming.
    • Confirm that your original remote control is an ALLMATIC model listed as compatible.
    • Make sure you are pressing and holding the buttons for the correct duration as specified in the programming steps.
    • Check the battery of the new remote.
  • Remote programmed but not operating the door/gate:
    • Ensure you have successfully completed the 'Auto Matching Code' procedure or the receiver registration process as per your original receiver's manual. This step is crucial for the receiver to recognize the new remote.
    • Verify that the receiver is powered on and functioning correctly.
    • Check for any obstructions between the remote and the receiver.
  • LED on new remote not flashing:
    • The battery might be depleted. Replace the battery.
    • Ensure buttons are pressed correctly during the initial programming sequence.

7. User Tips

  • Access to Receiver: Always ensure you have physical access to your garage door or gate receiver/opener before attempting to program the new remote. This is often required for the final registration step.
  • Original Remote Condition: For successful cloning, your original remote control must be in good working condition and emit a strong signal.
  • Multiple Functions: If your original remote has multiple buttons for different functions (e.g., opening a gate and a garage door), you can program each function to a separate button on the new universal remote.
  • Clear Programming Area: Perform programming in a quiet area, free from other radio frequency interference, to ensure accurate signal duplication.

8. Warranty and Support

For additional information, detailed diagrams, or specific troubleshooting related to your receiver, please consult the official user manual (PDF) available at: ALLMATIC Remote Control User Manual (PDF).

For product support or warranty inquiries, please contact your retailer or the manufacturer directly.

© 2023 ALLMATIC. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.