1. Introduction
The ANDELI TIG-250MPL is a versatile and portable MOS Tube Multifunctional TIG Welding Machine designed for a wide range of welding applications. It supports Hot TIG, Cold TIG, Pulse TIG, MMA (Manual Metal Arc), and Clean functions, making it suitable for both small operations and industrial use. This manual provides essential information for the safe and effective operation and maintenance of your welding machine.
2. Safety Instructions
Always prioritize safety when operating welding equipment. Failure to follow safety precautions can result in serious injury or death.
- Ensure proper ventilation to avoid inhaling welding fumes.
- Wear appropriate personal protective equipment (PPE), including welding helmet, gloves, and protective clothing.
- Never weld near flammable materials.
- Ensure the machine is properly grounded.
- Do not touch live electrical parts.
- Disconnect power before performing any maintenance or adjustments.
- Keep children and unauthorized personnel away from the welding area.
3. Package Contents
Upon unpacking, verify that all components are present and undamaged:
- TIG-250MPL Main Unit
- WP-17F TIG Torch
- WP-9F TIG Torch
- Ground Clamp
- 2-core Foot Switch
- Trachea (Gas Hose)
- Nozzles (various sizes)
- Contact Tips
- Tungsten Electrodes
- Power Cable
4. Setup
Follow these steps to set up your TIG-250MPL welding machine:
-
Power Connection: The machine supports dual voltage operation. Connect the power cable to either a 110V or 220V power source. The machine automatically adapts to the input voltage.
Figure 4.1: Dual voltage capability: 110V for small operations, 220V for industrial operations. - Gas Connection: Connect the trachea (gas hose) from your inert gas cylinder (e.g., Argon) to the gas inlet on the rear of the welding machine. Ensure all connections are secure to prevent gas leaks.
- TIG Torch Connection: Connect the TIG torch to the appropriate connector on the front panel of the machine. Ensure the gas line from the torch is also connected.
- Ground Clamp Connection: Attach the ground clamp cable to the designated terminal on the front panel. Securely attach the ground clamp to the workpiece or welding table to ensure a good electrical connection.
- Foot Switch Connection: If using, connect the 2-core foot switch to its designated port on the machine.
- Electrode Installation: Install the appropriate tungsten electrode and nozzle into the TIG torch head according to your welding requirements.
5. Operating Instructions
The TIG-250MPL offers multiple welding modes and precise control. Familiarize yourself with the control panel and modes before operation.
5.1 Control Panel Overview
- Mode Selection: Use the mode buttons to select between TIG, Cold Welder, MMA, Clean, and Pulse functions.
- Menu Switching: Navigate through different parameters using the menu switching buttons.
- Numeric Adjustment: Use the rotary knob and up/down buttons to precisely adjust welding current, time, frequency, and other settings.
5.2 Welding Modes
- TIG (Tungsten Inert Gas): Provides high-quality, precise welds for various metals.
- Cold Welder: Ideal for low-heat applications, minimizing material deformation.
- MMA (Manual Metal Arc): For stick welding with coated electrodes.
- Clean: A specialized function, likely for surface preparation or specific welding processes.
- Pulse: Offers enhanced control over heat input, especially useful for thin materials and out-of-position welding.
5.3 Low Temperature Welding for Thin Plates
The machine's cold welding feature allows for precise control of welding time to manage temperature, preventing penetration and minimizing deformation on thin workpieces. This is achieved through instant high current discharge in a short time.
5.4 Memory Storage
The TIG-250MPL features memory storage for up to 6 welding channels (01-06). This allows you to save and recall frequently used welding parameters, improving efficiency and consistency.
6. Maintenance
Regular maintenance ensures the longevity and optimal performance of your welding machine.
- Cleaning: Periodically clean the machine's exterior and ventilation openings to prevent dust and debris buildup. Use compressed air to clear internal components if necessary, ensuring the machine is unplugged.
- Cable Inspection: Regularly inspect all cables (power, torch, ground) for cuts, fraying, or damage. Replace damaged cables immediately.
- Torch and Consumables: Inspect the TIG torch, nozzles, collets, and tungsten electrodes for wear. Replace consumables as needed to maintain weld quality.
- Gas System: Check gas hoses and connections for leaks. Ensure the gas regulator is functioning correctly.
- Storage: Store the welding machine in a clean, dry environment when not in use.
7. Troubleshooting
This section addresses common issues you might encounter. For problems not listed here, contact customer support.
| Problem | Possible Cause | Solution |
|---|---|---|
| Machine does not power on | No power supply; Faulty power cable; Internal fuse blown | Check power outlet and circuit breaker; Inspect power cable; Contact service center. |
| No arc initiation | Poor ground connection; Incorrect welding parameters; Worn tungsten electrode; Gas flow issue | Ensure solid ground connection; Adjust current/voltage; Sharpen or replace tungsten; Check gas supply. |
| Poor weld quality | Incorrect settings; Contaminated workpiece; Improper gas shielding; Incorrect torch angle/travel speed | Adjust welding parameters; Clean workpiece thoroughly; Check gas flow and purity; Practice welding technique. |
| Overheating protection activated | Exceeded duty cycle; Blocked ventilation; High ambient temperature | Allow machine to cool down; Clear ventilation openings; Operate in a cooler environment. |
8. Specifications
Technical specifications for the ANDELI TIG-250MPL welding machine:
| Feature | Specification |
|---|---|
| Model | TIG-250MPL |
| Material / Metal Processed | Carbon steel, Stainless Steel |
| Tube Type | MOS |
| Functions | Hot TIG, Cold TIG, Pulse TIG, MMA, Clean |
| Power Voltage | 110V/220V (Dual Voltage) |
| Frequency | 50/60 Hz |
| Rated Input Capacity | 4.6 KVA |
| Rated Current Input | 20.9 A |
| Rated Output | 180A/17.2V |
| Rated Duty Cycle @40°C (TIG) | 60% (180A), 100% (140A) |
| HOT TIG Plate Thickness | 0.6-10mm |
| Cold TIG Output Current Range | 20-180 A |
| Cold TIG Output Current Time | 35-999 S |
| Cold TIG Plate Thickness | 0.2-3mm |
| Pulse TIG Peak Current | 10-250 A |
| Pulse TIG Pulse Frequency | 4-0.01 S |
| Pulse TIG Pulse Width (Ratio) | 5-95 |
| Pulse TIG Pre-Gas Time | 0-2 S |
| Pulse TIG Flow-Gas Time | 0.5-5 S |
| Pulse TIG Plate Thickness | 0.4-3mm |
| Efficiency | 85% |
| Power Factor | 0.76 |
| Insulation Class | H |
| Weight | 7.55 KG |
| Dimensions (L x W x H) | 377mm (14.8in) x 152mm (6in) x 234mm (9.2in) |
| Feature | PORTABLE |
| Applicable Industries | Building Material Shops, Machinery Repair Shops, Manufacturing Plant, Home Use, Construction works, Other |
9. User Tips
- For optimal performance, ensure your workpiece is clean and free of rust, paint, or oil before welding.
- Experiment with the memory storage function to quickly switch between common settings for different materials or tasks.
- When welding thin materials, utilize the Cold TIG or Pulse TIG modes to minimize heat input and prevent burn-through.
- Always use the correct size and type of tungsten electrode for your specific welding application and current.
10. Warranty and Support
The ANDELI TIG-250MPL welding machine comes with a 2-year warranty from the date of purchase, covering manufacturing defects. For technical support, warranty claims, or service inquiries, please contact your authorized dealer or ANDELI customer service.
ANDELI Group Co., Ltd. is a leading manufacturer in the electrical industry, founded in 1985. They are committed to producing high-quality electrical equipment. For further information or assistance, please refer to the contact details provided at the point of purchase or on the official ANDELI website.