1. Introduction and Overview
This manual provides detailed instructions for the safe and efficient operation of your MYAMi Laboratory Switching DC Power Supply. This programmable power supply is designed for various laboratory applications, including lithium battery charging and fuse performance testing, offering precise control over voltage and current output.
Key features of your MYAMi DC Power Supply include:
- 5-inch LCD screen for intuitive display and operation.
- Advanced embedded operating system for stable performance and precise data.
- Battery algorithm curve charging function to effectively reduce battery damage.
- Powerful multi-functional fuse blowing test mode for convenient fuse performance testing.
- Output positive timing and countdown testing functions.
- Support for MODBUS RTU protocol with standard RS485 interface, and optional USB and RS232 communication interfaces.
- Comprehensive protection features including OVP (Over Voltage Protection), OCP (Over Current Protection), and OTP (Over Temperature Protection).

Figure 1: Front view of the MYAMi DC Power Supply.

Figure 2: Overview of the 6000W DC Power Supply's upgraded features.
2. Setup
Before operating the device, ensure it is placed on a stable, level surface with adequate ventilation. Connect all necessary cables securely.
2.1 Power Connection
The power supply requires an AC 220V input. Do not use ordinary power plugs. Connect the AC input line of the power supply directly to a circuit breaker interface. Control the input on/off of the power supply through the circuit breaker.
2.2 Output Connections
Connect your load to the output terminals on the rear panel. Observe correct polarity (red for positive, black for negative). The SENSE compensation interface can be used for precise voltage regulation at the load.
2.3 Communication Interfaces
The device comes standard with an RS485 interface. Optional USB and RS232 interfaces may also be present for remote control and data logging. Connect the appropriate cable to the desired communication port on the rear panel.

Figure 3: Rear panel connections and power input instructions.
3. Operating Instructions
The MYAMi DC Power Supply features a user-friendly interface with a 5-inch LCD screen and a combination of buttons and rotary encoders for control.
3.1 Power On/Off
Press the red power button on the front panel to turn the unit on or off.
3.2 Navigation and Parameter Adjustment
Use the 'Mode' button to cycle through different operating modes: Normal Mode, Charge Mode, and Fuse Mode. Use the arrow keys and 'Adjustment & Enter' rotary encoder to navigate menus and adjust values. The numeric keypad allows for direct input of values.
Video 1: Demonstration of UI navigation and parameter adjustment.
3.3 Normal Mode
In Normal Mode, you can set the output voltage and current limits. The display shows real-time voltage, current, power, and run time. Use the 'Set' button to select the parameter to adjust (voltage or current), then use the rotary encoder or numeric keypad to change the value. Press 'Enter' to confirm.
3.4 Charge Mode (Battery Algorithm Curve Charging)
This mode is optimized for charging lithium batteries, utilizing a curve algorithm to minimize battery damage. To configure Charge Mode:
- Select 'Charge Mode' using the 'Mode' button.
- Press 'Config' on the screen or 'Enter' button to access charging parameters.
- Adjust 'Charge Voltage', 'Charge Current', 'Pre-charge Voltage', 'Pre-charge Current', 'Charge completion current threshold', and 'Charging time limit' using the controls.
- The display will show a graph of cell voltage, capacity, and current over time.
- Press 'Return' to exit configuration.

Figure 4: Battery charging process through algorithms.
3.5 Fuse Mode (Fuse Blowing Test)
This mode allows for convenient fuse performance testing. To configure Fuse Mode:
- Select 'Fuse Mode' using the 'Mode' button.
- Access the configuration menu.
- Choose between 'Fuse current mode' (to obtain instantaneous melting of fuses and critical current value) or 'Only fuse timing mode' (for constant current output to test fuse in ampere seconds (A-T) characteristics).
- Set parameters such as 'Fuse Time', 'Fuse Current', 'Current Start', 'Current End', 'Current Step', and 'Check Delay' as required for your test.

Figure 5: Fuse Mode configuration options.
3.6 Timing Functions
The power supply includes advanced timing functions:
- Timing Pause: Turn off output, run time does not reset to zero. Accumulated time after restarting output.
- Timing Reset: After turning off the output, the running time is reset to zero. Restart the output and restart the timer.
- Countdown: Pre-set the required running time. Turn off output after reaching the set time.

Figure 6: Timing function details.
4. Maintenance
To ensure the longevity and optimal performance of your MYAMi DC Power Supply, follow these maintenance guidelines:
- Cleaning: Regularly wipe the exterior of the unit with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure no liquids enter the device.
- Ventilation: Keep the ventilation openings on the sides and rear of the unit clear of obstructions to prevent overheating.
- Storage: Store the power supply in a cool, dry environment away from direct sunlight, excessive dust, and corrosive gases when not in use.
- Inspection: Periodically check all cables and connections for signs of wear or damage. Replace any damaged components immediately.
- Safety: Always disconnect the power supply from the main power source before performing any cleaning or maintenance.

Figure 7: Side view showing ventilation.
5. Troubleshooting
If you encounter issues with your MYAMi DC Power Supply, please refer to the following basic troubleshooting steps:
- No Power: Ensure the power cable is securely connected to both the unit and the circuit breaker. Verify that the circuit breaker is switched on and providing 220VAC.
- No Output: Check if the output is enabled in Normal Mode. Ensure the voltage and current settings are appropriate for your load. Verify that the load is correctly connected and not short-circuited.
- Overload/Protection Triggered: If OVP, OCP, or OTP indicators are active, disconnect the load and check for faults. Reduce the load or adjust settings to prevent exceeding the device's limits. Allow the unit to cool down if OTP is active.
- Display Issues: If the display is blank or unresponsive, try restarting the unit. If the problem persists, contact customer support.
- Communication Issues: Ensure the correct communication cable is used and properly connected. Verify software settings and drivers if using a PC for control.
For persistent issues, please contact MYAMi customer support.
6. Specifications
| Feature | Specification |
|---|---|
| Brand Name | MYAMi |
| Model | MY-K6020PL |
| Input Voltage | 220VAC |
| Output Voltage | Up to 30V |
| Output Current | Up to 200A |
| Output Power | Up to 6000W |
| Display | 5-inch LCD Color Screen |
| Operating System | Embedded Operating System |
| Communication Interfaces | RS485 (Standard), USB, RS232 (Optional) |
| Protection Features | OVP, OCP, OTP |
| Package Length | 52 cm |
| Package Width | 35 cm |
| Package Height | 26 cm |
| Package Weight | 11.0 kg |
| Origin | Mainland China |
7. User Tips
- Always double-check your voltage and current settings before connecting a sensitive load to prevent damage.
- Utilize the 'Charge Mode' for lithium batteries to benefit from the optimized charging algorithm, which helps prolong battery life.
- When performing fuse tests, ensure you understand the fuse's specifications and select the appropriate test mode and parameters to avoid damaging the fuse or the power supply.
- For remote control or data logging, ensure the correct communication interface (USB, RS232, or RS485) is selected and configured in the device settings and your control software.
- Keep the device's firmware updated if new versions are released by the manufacturer to ensure access to the latest features and bug fixes.
8. Warranty and Support
For warranty information, technical support, or service inquiries, please contact MYAMi Official Store directly. Keep your purchase receipt or order details handy when contacting support.