Merlin E960M Premium Garage Door Remote Control User Manual

1. Introduction

The Merlin E960M is a premium garage door remote control designed for convenience and security. It features rolling code encryption to ensure secure operation of your garage door or gate opener. This manual provides detailed instructions for setting up, operating, and maintaining your remote control.

Figure 1: Merlin E960M Remote Control

2. Features

• Secure Rolling Code: Generates a unique code with each activation (Security+ 2.0 encryption) to prevent code grabbing.
• Multi-Frequency Operation: Supports 433.30MHz, 433.92MHz, and 434.54MHz.
• LED Indicator: Green LED light flashes when a button is pressed.
• Four Programmable Buttons: Allows control of up to four different door or gate openers.
• Broad Compatibility: Designed for MERLIN+ and MERLIN+ 2.0 receivers, and fits all Security+, Security+ 2.0, some Legacy FM Merlin motors, and some Motorlift motors.

3. Specifications

Figure 2: Back of E960M Remote Control with Specifications

4. Package Contents

• 1 x Merlin E960M Remote Control
• 1 x Battery (pre-installed)
• 1 x English Instruction Manual
• 1 x Keychain

5. Compatibility

The Merlin E960M remote control is compatible with a wide range of Merlin and Motorlift garage door and gate openers. Please ensure your existing remote or opener model is listed below for guaranteed compatibility. Access to your receiver/opener is required for programming.

Compatible Models List:

• Roller Door Motors: Merlin MR550EVO WeatherDrive, Merlin MR650EVO Quiet Drive, Merlin MR850EVO Silent Drive, Merlin MR655MYQ SilentDrive Essential, Merlin MR855MYQ SilentDrive Elite, Merlin MR600, Merlin MR650, Merlin MR800, Merlin MR800A, Merlin MR850, Merlin MR60, Merlin MR1000, Chamberlain CR650EVO Handylift.
• Industrial Motors: Merlin MRC950 Overdrive Light Industrial Roller Door Motor, Merlin MRC950EVO Overdrive Light Industrial Roller Door Motor, Grifco GLD-RDO Light Industrial Motor.
• Gate Motors: Merlin MGA300, Merlin MGS300, Merlin MGS400, Merlin MGS500, Merlin MGS1000, Motorlift HC100ML, Motorlift HC300ML, Motorlift HC400ML, Motorlift HC500ML, Motorlift HC600ML.
• Sectional / Panel Door Motors: Merlin MT3850EVO WhisperDrive Sectional Door Motor, Merlin MT120EVOPS Cyclone Pro Panel Door Motor, Merlin MT100EVO Tiltmaster Panel Door Motor, Merlin MT60EVO PowerAce Panel Door Motor, Merlin MS65MYQ Commander Essential, Merlin MS105MYQ Commander Elite, Merlin MS125MYQ Commander Extreme, Merlin MJ3800MYQ, Merlin MT60, Merlin MT60P, Merlin MT230, Merlin MT600, Merlin MT800, Merlin MT1000, Merlin MJ3800, Merlin MJ3800R, Merlin MT5580, CS60EVO Powerlift, CS100EVO Powerlift Plus, Motorlift ML700, Motorlift ML750, Motorlift ML850, HC100ML, HC300ML, HC400ML, HC500ML, HC600ML, LiftMaster 3800.

Figure 3: Examples of Compatible Remote Controls

6. Setup and Programming

Follow these steps to program your Merlin E960M remote control:

1. Enter Switching Code Mode: Press and hold the '2' (left) and '3' (right) buttons on the remote control simultaneously for approximately 6 seconds. The indicator light will remain on. Release the buttons to enter switching code mode.
   

   Figure 4: Holding Buttons 2 and 3

2. Select Code Type: While in switching code mode, press the button you wish to program a specific number of times to select the desired code type:
   • Press 1 time for Merlin 2.0 (433.3MHz, 433.92MHz, 434.54MHz).
   • Press 2 times for 433.92MHz Liftmaster.
   • Press 3 times for 433.92MHz Billion Code.
   

   Figure 5: Selecting Code Type
3. Exit Switching Code Mode: After selecting the code type, press any other button on the remote control to exit the switching code mode.
   

   Figure 6: Exiting Code Switching Mode

4. Learn with Receiver: Once the remote control is configured with the correct code type, use it to learn with your corresponding garage door or gate receiver. Refer to your opener's instruction manual for specific receiver learning procedures.
   

   Figure 7: Learning with Receiver

7. Operating Instructions

After successful programming, operate your garage door or gate opener by simply pressing the corresponding programmed button on the remote control. The green LED light will illuminate briefly with each press, indicating signal transmission.

8. Maintenance

• Battery Replacement: The remote control uses a standard coin cell battery. If the LED indicator light becomes dim or the remote's range decreases, it may be time to replace the battery. Carefully open the remote casing (usually by prying gently with a small flat-head screwdriver) and replace the battery with a new one of the same type.
• Cleaning: Clean the remote control with a soft, dry cloth. Avoid using abrasive cleaners or solvents, as these can damage the casing or internal components.
• Storage: Store the remote control in a dry place, away from extreme temperatures and direct sunlight.

9. Troubleshooting

• Remote Not Working:
  • Check if the LED indicator lights up when a button is pressed. If not, replace the battery.
  • Ensure the remote is correctly programmed to your receiver. Repeat the programming steps if necessary.
  • Verify that your garage door or gate opener is powered on and functioning correctly.
• Reduced Range:
  • Replace the battery.
  • Check for any obstructions between the remote and the receiver.
  • Ensure the antenna on your receiver is extended and unobstructed.
• Interference: Other radio frequency devices nearby might cause interference. Try operating the remote from a different location or temporarily disabling other devices to diagnose.

10. User Tips

• Verify Compatibility: Before purchasing or programming, always confirm that your existing garage door or gate opener model is explicitly listed in the compatibility section of this manual. If your model is not listed (e.g., Merlin E970M), compatibility cannot be guaranteed.
• Receiver Access: Programming the remote requires physical access to your garage door or gate opener's receiver. Ensure you can reach the 'Learn' or 'Program' button on your opener unit.
• Multiple Openers: Utilize the four distinct buttons to control different garage doors or gates, provided each opener is compatible and can be programmed separately.

11. Warranty and Support

For any issues, technical support, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.