REMOCON RMC-600

Contents

REMOCON RMC-600 Fixed Code Adjustable Frequency Remote Control User Manual

Model: YNG129

1. Product Overview

The REMOCON RMC-600 is a versatile 4-button fixed code remote control designed for electric gates and garage doors. It features an adjustable frequency range of 250MHz-450MHz, allowing it to duplicate a wide variety of existing fixed code remote controls. This remote is self-learning and comes with a 12V 23A battery included.

Important Note: This remote control is designed to duplicate fixed code remote controls only. It cannot clone remotes that utilize 'Code Hopping' or 'Anti-Code Grabbing Technology', as these types of remotes transmit a different code each time a button is pressed.

Multiple REMOCON RMC-600 remote controls
Figure 1: REMOCON RMC-600 Remote Controls

2. Package Contents

  • REMOCON RMC-600 Remote Control
  • 12V 23A Battery (pre-installed)
  • Keychain
  • English Manual (this document)

3. Specifications

AttributeValue
Model NumberYNG129
Encoding MethodFixed Code (Self-learning)
Frequency Range250MHz-450MHz (Adjustable)
Number of Buttons4 Buttons
Battery Type12V 23A (Included)
Dimensions (L x W x H)60mm x 35mm x 15mm
MaterialABS
OriginMainland China
CertificationCE, FCC, RoHS, WEEE

4. Setup and Cloning Instructions

Follow these steps carefully to clone your existing fixed code remote control to the REMOCON RMC-600.

Diagram showing internal components of the remote, including jumpers and frequency adjuster
Figure 2: Internal Components and Frequency Adjustment Points
  1. **Setting the Frequency:**
    1. Ensure Jumper 2 is installed. Place your existing remote and the REMOCON remote within 1 cm of each other.
    2. Press and hold any button on both remotes simultaneously.
    3. Using the provided tuning bar (small screwdriver), adjust the 'Frequency adjuster' on the REMOCON remote until its LED flashes 3 times.
    4. While still holding the buttons, increase the distance between the two remotes to about 3 cm. Observe the brightness of the REMOCON remote's LED. Adjust the frequency further until the LED shows maximum brightness.
    5. If a suitable adjustment cannot be found, change Jumper 1 to the next 2-pin position and repeat from step 'a'.
    6. (Optional) If you have a frequency counter, you can remove Jumper 2 and adjust the frequency using the counter. Remember to re-install Jumper 2 for the next procedure.
  2. **Cloning the Code:**
    1. Place the two remotes within 2 cm of each other.
    2. Press and hold the button on your existing remote that you wish to copy.
    3. Simultaneously, press and hold the corresponding button on the REMOCON remote where you want to store the code.
    4. Wait until the LED of the REMOCON remote flashes 3 times. This indicates successful cloning.
    5. Repeat the above steps for any other buttons you wish to copy.
  3. **Finalizing Setup:**
    1. Once all desired buttons are cloned, remove Jumper 2.
    2. Place Jumper 2 in a way that only one leg is connected (e.g., on a single pin). This prevents losing the jumper for future programming.

Important: Program remotes in areas free from electrical interference to avoid incorrect programming.

Video 1: Demonstration of the cloning process for the REMOCON RMC-600.

5. Operating Instructions

Once successfully cloned, operate the REMOCON RMC-600 remote control as you would your original remote. Press the corresponding button on the REMOCON remote to activate the desired function (e.g., open/close gate, arm/disarm alarm).

Front view of a single REMOCON RMC-600 remote control with four buttons
Figure 3: Front view of the REMOCON RMC-600 Remote Control

6. Maintenance

  • Battery Replacement: The remote uses a 12V 23A battery. If the remote's LED does not light up or is dim when a button is pressed, the battery may need replacement. To replace, carefully open the remote casing (usually by removing a small screw on the back) and swap the old battery with a new 12V 23A battery, ensuring correct polarity.
  • Cleaning: Wipe the remote control with a soft, dry cloth. Avoid using harsh chemicals or abrasive cleaners.
  • Storage: Store the remote in a dry place, away from extreme temperatures and direct sunlight.
Front and back view of the REMOCON RMC-600 remote control
Figure 4: Front and Back of the Remote Control

7. Troubleshooting

  • Remote not cloning successfully:
    • Ensure your original remote is a fixed code type. This remote cannot clone 'code hopping' or 'rolling code' remotes.
    • Verify your original remote is working correctly before attempting to clone.
    • Make sure the remotes are within the specified distance (1-3 cm) during frequency adjustment and cloning.
    • Check the battery in both remotes. A weak battery can hinder the cloning process.
    • Try adjusting the frequency again, ensuring the REMOCON LED flashes 3 times and then shows maximum brightness.
    • Ensure there is no significant electrical interference in the programming area.
  • Remote not working after cloning:
    • Re-verify the cloning steps. It's possible the code was not transferred correctly.
    • Confirm that Jumper 2 was removed after cloning.
    • Test the original remote to ensure the receiver is still functioning.
  • LED not lighting up or dim:
    • The battery may be low or depleted. Replace the 12V 23A battery.

8. User Tips

  • Always keep your original working remote in a safe place. The REMOCON RMC-600 requires a functional original remote for cloning.
  • If you have multiple fixed code remotes operating on the same frequency, you can clone them all onto different buttons of a single REMOCON RMC-600.
  • For optimal performance, avoid programming or operating the remote in areas with strong electromagnetic interference.
  • If you encounter difficulties, refer to the video demonstration provided in the Setup section or contact customer support for assistance.

9. Warranty and Support

Your satisfaction is important to us. If you experience any issues with your REMOCON RMC-600 remote control, please contact our customer support team. We are committed to providing assistance and resolving any problems you may encounter.

  • Product Malfunction: If the product cannot be used normally due to a manufacturing defect, please contact us for support.
  • Quality Issues: For any quality-related concerns, we will provide a satisfactory resolution within the agreed timeframe.
  • Missing or Incorrect Items: In the rare event of an omission or incorrect delivery, please contact us immediately for a satisfactory solution.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.